Attachment 1456320 Details for Bug 1595319 – iw phy0 info

iw phy0 info

iw-phy0-info.txt (text/plain), 3.93 KB, created by Juhani Jaakola on 2018-07-03 19:12:01 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Juhani Jaakola

Created: 2018-07-03 19:12:01 UTC

Size: 3.93 KB

patch

obsolete

># iw phy0 info
>Wiphy phy0
>	max # scan SSIDs: 4
>	max scan IEs length: 2257 bytes
>	max # sched scan SSIDs: 0
>	max # match sets: 0
>	max # scan plans: 1
>	max scan plan interval: -1
>	max scan plan iterations: 0
>	Retry short limit: 7
>	Retry long limit: 4
>	Coverage class: 0 (up to 0m)
>	Device supports RSN-IBSS.
>	Supported Ciphers:
>		* WEP40 (00-0f-ac:1)
>		* WEP104 (00-0f-ac:5)
>		* TKIP (00-0f-ac:2)
>		* CCMP-128 (00-0f-ac:4)
>		* CCMP-256 (00-0f-ac:10)
>		* GCMP-128 (00-0f-ac:8)
>		* GCMP-256 (00-0f-ac:9)
>	Available Antennas: TX 0 RX 0
>	Supported interface modes:
>		 * IBSS
>		 * managed
>		 * AP
>		 * AP/VLAN
>		 * monitor
>	Band 1:
>		Capabilities: 0x7c
>			HT20
>			SM Power Save disabled
>			RX Greenfield
>			RX HT20 SGI
>			RX HT40 SGI
>			No RX STBC
>			Max AMSDU length: 3839 bytes
>			No DSSS/CCK HT40
>		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
>		Minimum RX AMPDU time spacing: 8 usec (0x06)
>		HT Max RX data rate: 72 Mbps
>		HT TX/RX MCS rate indexes supported: 0-7
>		Bitrates (non-HT):
>			* 1.0 Mbps
>			* 2.0 Mbps (short preamble supported)
>			* 5.5 Mbps (short preamble supported)
>			* 11.0 Mbps (short preamble supported)
>			* 6.0 Mbps
>			* 9.0 Mbps
>			* 12.0 Mbps
>			* 18.0 Mbps
>			* 24.0 Mbps
>			* 36.0 Mbps
>			* 48.0 Mbps
>			* 54.0 Mbps
>		Frequencies:
>			* 2412 MHz [1] (30.0 dBm)
>			* 2417 MHz [2] (30.0 dBm)
>			* 2422 MHz [3] (30.0 dBm)
>			* 2427 MHz [4] (30.0 dBm)
>			* 2432 MHz [5] (30.0 dBm)
>			* 2437 MHz [6] (30.0 dBm)
>			* 2442 MHz [7] (30.0 dBm)
>			* 2447 MHz [8] (30.0 dBm)
>			* 2452 MHz [9] (30.0 dBm)
>			* 2457 MHz [10] (30.0 dBm)
>			* 2462 MHz [11] (30.0 dBm)
>			* 2467 MHz [12] (disabled)
>			* 2472 MHz [13] (disabled)
>			* 2484 MHz [14] (disabled)
>	Supported commands:
>		 * new_interface
>		 * set_interface
>		 * new_key
>		 * start_ap
>		 * new_station
>		 * new_mpath
>		 * set_mesh_config
>		 * set_bss
>		 * authenticate
>		 * associate
>		 * deauthenticate
>		 * disassociate
>		 * join_ibss
>		 * join_mesh
>		 * set_tx_bitrate_mask
>		 * frame
>		 * frame_wait_cancel
>		 * set_wiphy_netns
>		 * set_channel
>		 * set_wds_peer
>		 * probe_client
>		 * set_noack_map
>		 * register_beacons
>		 * start_p2p_device
>		 * set_mcast_rate
>		 * connect
>		 * disconnect
>		 * set_qos_map
>		 * set_multicast_to_unicast
>	Supported TX frame types:
>		 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>		 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>		 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>		 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>		 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>		 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>		 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>		 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>	Supported RX frame types:
>		 * IBSS: 0x40 0xb0 0xc0 0xd0
>		 * managed: 0x40 0xd0
>		 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>		 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>		 * mesh point: 0xb0 0xc0 0xd0
>		 * P2P-client: 0x40 0xd0
>		 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>		 * P2P-device: 0x40 0xd0
>	software interface modes (can always be added):
>		 * AP/VLAN
>		 * monitor
>	interface combinations are not supported
>	HT Capability overrides:
>		 * MCS: ff ff ff ff ff ff ff ff ff ff
>		 * maximum A-MSDU length
>		 * supported channel width
>		 * short GI for 40 MHz
>		 * max A-MPDU length exponent
>		 * min MPDU start spacing
>	Device supports TX status socket option.
>	Device supports HT-IBSS.
>	Device supports SAE with AUTHENTICATE command
>	Device supports low priority scan.
>	Device supports scan flush.
>	Device supports AP scan.
>	Device supports per-vif TX power setting
>	Driver supports full state transitions for AP/GO clients
>	Driver supports a userspace MPM
>	Device supports configuring vdev MAC-addr on create.

Actions: View

Attachments on bug 1595319: 1454696 | 1454700 | 1454884 | 1456320