Attachment 147626 Details for Bug 220470 – Kai's working fc7 boot log w/ mkinitrd --preload=sym53c8xx --preload=pata_via

Kai's working fc7 boot log w/ mkinitrd --preload=sym53c8xx --preload=pata_via

surprise1.txt (text/plain), 16.34 KB, created by Kai Engert (:kaie) (inactive account) on 2007-02-08 01:56:55 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Kai Engert (:kaie) (inactive account)

Created: 2007-02-08 01:56:55 UTC

Size: 16.34 KB

patch

obsolete

>Linux version 2.6.20-1.2922.fc7 (brewbuilder@hs20-bc2-2.build.redhat.com) (gcc version 4.1.1 20070123 (Red Hat 4.1.1-54)) #1 SMP Sun Feb 4 18:53:10 EST 2007
>BIOS-provided physical RAM map:
>sanitize start
>sanitize end
>copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
>copy_e820_map() type is E820_RAM
>copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
>copy_e820_map() start: 00000000000d0000 size: 0000000000008000 end: 00000000000d8000 type: 2
>copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
>copy_e820_map() start: 0000000000100000 size: 000000003fef0000 end: 000000003fff0000 type: 1
>copy_e820_map() type is E820_RAM
>copy_e820_map() start: 000000003fff0000 size: 0000000000008000 end: 000000003fff8000 type: 3
>copy_e820_map() start: 000000003fff8000 size: 0000000000008000 end: 0000000040000000 type: 4
>copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
>copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
>copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
> BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
> BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
>127MB HIGHMEM available.
>896MB LOWMEM available.
>found SMP MP-table at 000fb930
>Using x86 segment limits to approximate NX protection
>Zone PFN ranges:
>  DMA             0 ->     4096
>  Normal       4096 ->   229376
>  HighMem    229376 ->   262128
>early_node_map[1] active PFN ranges
>    0:        0 ->   262128
>DMI 2.3 present.
>Using APIC driver default
>ACPI: PM-Timer IO Port: 0x808
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
>Processor #0 6:6 APIC version 16
>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
>Enabling APIC mode:  Flat.  Using 1 I/O APICs
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
>Detected 1100.159 MHz processor.
>Built 1 zonelists.  Total pages: 258801
>Kernel command line: ro root=/dev/sdb3 console=ttyS0,9600n8 console=tty0 1
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Initializing CPU#0
>CPU 0 irqstacks, hard=c0784000 soft=c0764000
>PID hash table entries: 4096 (order: 12, 16384 bytes)
>Console: colour VGA+ 80x25
>Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
>... MAX_LOCKDEP_SUBCLASSES:    8
>... MAX_LOCK_DEPTH:          30
>... MAX_LOCKDEP_KEYS:        2048
>... CLASSHASH_SIZE:           1024
>... MAX_LOCKDEP_ENTRIES:     8192
>... MAX_LOCKDEP_CHAINS:      16384
>... CHAINHASH_SIZE:          8192
> memory used by lock dependency info: 1064 kB
> per task-struct memory footprint: 1200 bytes
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 1024468k/1048512k available (2081k kernel code, 23308k reserved, 1111k data, 240k init, 131008k highmem)
>virtual kernel memory layout:
>    fixmap  : 0xffc56000 - 0xfffff000   (3748 kB)
>    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
>    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
>    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
>      .init : 0xc0723000 - 0xc075f000   ( 240 kB)
>      .data : 0xc060851f - 0xc071e414   (1111 kB)
>      .text : 0xc0400000 - 0xc060851f   (2081 kB)
>Checking if this processor honours the WP bit even in supervisor mode... Ok.
>Calibrating delay using timer specific routine.. 2202.15 BogoMIPS (lpj=1101077)
>Security Framework v1.0.0 initialized
>SELinux:  Initializing.
>SELinux:  Starting in permissive mode
>selinux_register_security:  Registering secondary module capability
>Capability LSM initialized as secondary
>Mount-cache hash table entries: 512
>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>CPU: L2 Cache: 256K (64 bytes/line)
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>Checking 'hlt' instruction... OK.
>SMP alternatives: switching to UP code
>Freeing SMP alternatives: 11k freed
>ACPI: Core revision 20060707
>CPU0: AMD Athlon(tm)  stepping 02
>Total of 1 processors activated (2202.15 BogoMIPS).
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
>Brought up 1 CPUs
>NET: Registered protocol family 16
>ACPI: bus type pci registered
>PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
>PCI: Using configuration type 1
>Setting up standard PCI resources
>ACPI: Interpreter enabled
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI quirk: region 0800-087f claimed by vt8235 PM
>PCI quirk: region 0400-040f claimed by vt8235 SMB
>ACPI: Power Resource [URP1] (off)
>ACPI: Power Resource [URP2] (off)
>ACPI: Power Resource [FDDP] (off)
>ACPI: Power Resource [LPTP] (off)
>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI init
>pnp: PnP ACPI: found 10 devices
>usbcore: registered new interface driver usbfs
>usbcore: registered new interface driver hub
>usbcore: registered new device driver usb
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
>NetLabel: Initializing
>NetLabel:  domain hash size = 128
>NetLabel:  protocols = UNLABELED CIPSOv4
>NetLabel:  unlabeled traffic allowed by default
>PCI: Bridge: 0000:00:01.0
>  IO window: disabled.
>  MEM window: cde00000-cfefffff
>  PREFETCH window: add00000-bdcfffff
>NET: Registered protocol family 2
>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
>TCP established hash table entries: 131072 (order: 10, 4194304 bytes)
>TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>TCP reno registered
>checking if image is initramfs... it is
>Freeing initrd memory: 2844k freed
>apm: BIOS not found.
>audit: initializing netlink socket (disabled)
>audit(1170906830.264:1): initialized
>highmem bounce pool size: 64 pages
>Total HugeTLB memory allocated, 0
>VFS: Disk quotas dquot_6.5.1
>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>SELinux:  Registering netfilter hooks
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>ACPI: Processor [CPU1] (supports 16 throttling states)
>isapnp: Scanning for PnP cards...
>isapnp: No Plug & Play device found
>Real Time Clock Driver v1.12ac
>Non-volatile memory driver v1.2
>Linux agpgart interface v0.101 (c) Dave Jones
>agpgart: Detected VIA KT400/KT400A/KT600 chipset
>agpgart: AGP aperture is 128M @ 0xe0000000
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
>usbcore: registered new interface driver libusual
>usbcore: registered new interface driver hiddev
>usbcore: registered new interface driver usbhid
>drivers/usb/input/hid-core.c: v2.6:USB HID core driver
>PNP: No PS/2 controller found. Probing ports directly.
>serio: i8042 KBD port at 0x60,0x64 irq 1
>serio: i8042 AUX port at 0x60,0x64 irq 12
>mice: PS/2 mouse device common for all mice
>TCP bic registered
>Initializing XFRM netlink socket
>NET: Registered protocol family 1
>NET: Registered protocol family 17
>powernow-k8: Processor cpuid 662 not supported
>Using IPI No-Shortcut mode
>Time: tsc clocksource has been installed.
>ACPI: (supports S0 S1 S4 S5)
>Freeing unused kernel memory: 240k freed
>Write protecting the kernel read-only data: 806k
>SCSI subsystem initialized
>ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 16
>sym0: <896> rev 0x7 at pci 0000:00:06.0 irq 16
>sym0: Symbios NVRAM, ID 7, Fast-40, SE, parity checking
>sym0: open drain IRQ line driver, using on-chip SRAM
>sym0: using LOAD/STORE-based firmware.
>sym0: handling phase mismatch from SCRIPTS.
>sym0: SCSI BUS has been reset.
>scsi0 : sym-2.2.3
> target0:0:0: Multiple LUNs disabled in NVRAM
>ACPI: PCI Interrupt 0000:00:06.1[B] -> GSI 18 (level, low) -> IRQ 17
>sym1: <896> rev 0x7 at pci 0000:00:06.1 irq 17
>sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
>sym1: open drain IRQ line driver, using on-chip SRAM
>sym1: using LOAD/STORE-based firmware.
>sym1: handling phase mismatch from SCRIPTS.
>sym1: SCSI BUS has been reset.
>scsi1 : sym-2.2.3
>ACPI: Unable to derive IRQ for device 0000:00:11.1
>ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
>ata1: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFC00 irq 14
>ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xFC08 irq 15
>scsi2 : pata_via
>ata1.00: ATAPI, max UDMA/33
>ata1.01: ATAPI, max UDMA/33
>ata1.00: device is on DMA blacklist, disabling DMA
>ata1.00: configured for PIO4
>ata1.01: configured for UDMA/33
>scsi3 : pata_via
>ata2.00: ATA-7, max UDMA/100, 156368016 sectors: LBA48 
>ata2.00: ata2: dev 0 multi count 16
>ata2.00: configured for UDMA/33
>scsi: waiting for bus probes to complete ...
>scsi 1:0:0:0: Direct-Access     IBM      DPSS-336950N     S96H PQ: 0 ANSI: 3
> target1:0:0: tagged command queuing enabled, command queue depth 16.
> target0:0:1: Multiple LUNs disabled in NVRAM
> target1:0:0: Beginning Domain Validation
> target1:0:0: asynchronous
>scsi 0:0:1:0: Optical Device    FUJITSU  MCF3064SS        0020 PQ: 0 ANSI: 2
> target0:0:1: Beginning Domain Validation
> target0:0:1: asynchronous
> target1:0:0: wide asynchronous
> target1:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
> target1:0:0: Domain Validation skipping write tests
> target0:0:1: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
> target1:0:0: Ending Domain Validation
> target0:0:1: Domain Validation skipping write tests
> target0:0:1: Ending Domain Validation
> target0:0:2: Multiple LUNs disabled in NVRAM
> target0:0:3: Multiple LUNs disabled in NVRAM
> target0:0:4: Multiple LUNs disabled in NVRAM
> target0:0:5: Multiple LUNs disabled in NVRAM
> target0:0:6: Multiple LUNs disabled in NVRAM
> target0:0:8: Multiple LUNs disabled in NVRAM
> target0:0:9: Multiple LUNs disabled in NVRAM
> target0:0:10: Multiple LUNs disabled in NVRAM
> target0:0:11: Multiple LUNs disabled in NVRAM
> target0:0:12: Multiple LUNs disabled in NVRAM
> target0:0:13: Multiple LUNs disabled in NVRAM
> target0:0:14: Multiple LUNs disabled in NVRAM
> target0:0:15: Multiple LUNs disabled in NVRAM
>sd 0:0:1:0: Attached scsi removable disk sda
>SCSI device sdb: 72170880 512-byte hdwr sectors (36951 MB)
>sdb: Write Protect is off
>SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>SCSI device sdb: 72170880 512-byte hdwr sectors (36951 MB)
>sdb: Write Protect is off
>SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdb: sdb1 sdb2 sdb3
>sd 1:0:0:0: Attached scsi disk sdb
>scsi 2:0:0:0: CD-ROM            ATAPI    CD-ROM DRIVE-40X N0BP PQ: 0 ANSI: 5
>scsi 2:0:1:0: CD-ROM            SONY     DVD RW DRU-510A  1.1a PQ: 0 ANSI: 5
>scsi 3:0:0:0: Direct-Access     ATA      SAMSUNG SP0822N  WA10 PQ: 0 ANSI: 5
>SCSI device sdc: 156368016 512-byte hdwr sectors (80060 MB)
>sdc: Write Protect is off
>SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>SCSI device sdc: 156368016 512-byte hdwr sectors (80060 MB)
>sdc: Write Protect is off
>SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 >
>sd 3:0:0:0: Attached scsi disk sdc
>USB Universal Host Controller Interface driver v3.0
>ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 18
>uhci_hcd 0000:00:10.0: UHCI Host Controller
>uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
>uhci_hcd 0000:00:10.0: irq 18, io base 0x0000d400
>usb usb1: configuration #1 chosen from 1 choice
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 18
>uhci_hcd 0000:00:10.1: UHCI Host Controller
>uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
>uhci_hcd 0000:00:10.1: irq 18, io base 0x0000d800
>usb usb2: configuration #1 chosen from 1 choice
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 18
>uhci_hcd 0000:00:10.2: UHCI Host Controller
>uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
>uhci_hcd 0000:00:10.2: irq 18, io base 0x0000dc00
>usb usb3: configuration #1 chosen from 1 choice
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 2 ports detected
>usb 1-1: new low speed USB device using uhci_hcd and address 2
>ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 18
>ehci_hcd 0000:00:10.3: EHCI Host Controller
>ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
>ehci_hcd 0000:00:10.3: irq 18, io mem 0xdbfdfe00
>ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>usb usb4: configuration #1 chosen from 1 choice
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 6 ports detected
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs: mounted filesystem with ordered data mode.
>usb 1-1: new low speed USB device using uhci_hcd and address 3
>usb 1-1: configuration #1 chosen from 1 choice
>input: HID 2101:020f as /class/input/input0
>input: USB HID v1.01 Keyboard [HID 2101:020f] on usb-0000:00:10.0-1
>input: HID 2101:020f as /class/input/input1
>input: USB HID v1.01 Mouse [HID 2101:020f] on usb-0000:00:10.0-1
>audit(1170906852.296:2): enforcing=1 old_enforcing=0 auid=4294967295
>security:  3 users, 6 roles, 1604 types, 204 bools, 1 sens, 1024 cats
>security:  59 classes, 50374 rules
>security:  class dccp_socket not defined in policy
>security:  permission dccp_recv in class node not defined in policy
>security:  permission dccp_send in class node not defined in policy
>security:  permission dccp_recv in class netif not defined in policy
>security:  permission dccp_send in class netif not defined in policy
>SELinux:  Completing initialization.
>SELinux:  Setting up existing superblocks.
>SELinux: initialized (dev sdb3, type ext3), uses xattr
>SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
>SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
>SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
>SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
>SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
>SELinux: initialized (dev devpts, type devpts), uses transition SIDs
>SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
>SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
>SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
>SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
>SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
>SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
>SELinux: initialized (dev proc, type proc), uses genfs_contexts
>SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
>SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
>SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
>audit(1170906854.819:3): policy loaded auid=4294967295

Actions: View

Attachments on bug 220470: 144195 | 147108 | 147122 | 147123 | 147502 | 147560 | 147613 | 147614 | 147615 | 147622 | 147623 | 147625 | 147626 | 147661 | 148114 | 148115 | 149620