Attachment 151337 Details for Bug 234106 – Output from dmesg for the kernel that write access works.

Output from dmesg for the kernel that write access works.

Fc5dmesg.txt (text/plain), 12.76 KB, created by Kelly-Rand on 2007-03-30 23:46:55 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Kelly-Rand

Created: 2007-03-30 23:46:55 UTC

Size: 12.76 KB

patch

obsolete

>Bootdata ok (command line is ro root=LABEL=/ rhgb quiet iommu=noaperture)
>Linux version 2.6.17-2174.bag.v2 (dad@bagend) (gcc version 4.1.1 20060525 (Red Hat 4.1.1-1)) #1 Mon Aug 21 07:15:15 EDT 2006
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable)
> BIOS-e820: 000000001ffc0000 - 000000001ffd0000 (ACPI data)
> BIOS-e820: 000000001ffd0000 - 0000000020000000 (ACPI NVS)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
>DMI 2.3 present.
>ACPI: RSDP (v002 ACPIAM                                ) @ 0x00000000000f9ed0
>ACPI: XSDT (v001 A M I  OEMXSDT  0x09000506 MSFT 0x00000097) @ 0x000000001ffc0100
>ACPI: FADT (v003 A M I  OEMFACP  0x09000506 MSFT 0x00000097) @ 0x000000001ffc0290
>ACPI: MADT (v001 A M I  OEMAPIC  0x09000506 MSFT 0x00000097) @ 0x000000001ffc0390
>ACPI: OEMB (v001 A M I  OEMBIOS  0x09000506 MSFT 0x00000097) @ 0x000000001ffd0040
>ACPI: DSDT (v001  A0128 A0128003 0x00000003 INTL 0x02002026) @ 0x0000000000000000
>On node 0 totalpages: 127831
>  DMA zone: 2654 pages, LIFO batch:0
>  DMA32 zone: 125177 pages, LIFO batch:31
>Nvidia board detected. Ignoring ACPI timer override.
>ACPI: PM-Timer IO Port: 0x4008
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
>Processor #0 15:12 APIC version 16
>ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>ACPI: BIOS IRQ0 pin2 override ignored.
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
>ACPI: IRQ9 used by override.
>ACPI: IRQ14 used by override.
>ACPI: IRQ15 used by override.
>Setting APIC routing to flat
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
>Built 1 zonelists
>Kernel command line: ro root=LABEL=/ rhgb quiet iommu=noaperture
>Initializing CPU#0
>PID hash table entries: 2048 (order: 11, 16384 bytes)
>time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
>time.c: Detected 1607.837 MHz processor.
>Console: colour VGA+ 80x25
>Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
>Memory: 509276k/524032k available (2449k kernel code, 14104k reserved, 973k data, 196k init)
>Calibrating delay using timer specific routine.. 3216.63 BogoMIPS (lpj=1608318)
>Security Framework v1.0.0 initialized
>SELinux:  Initializing.
>SELinux:  Starting in permissive mode
>selinux_register_security:  Registering secondary module capability
>Capability LSM initialized as secondary
>Mount-cache hash table entries: 256
>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>CPU: L2 Cache: 256K (64 bytes/line)
>CPU: AMD Sempron(tm) Processor 2800+ stepping 02
>Using local APIC timer interrupts.
>result 12561239
>Detected 12.561 MHz APIC timer.
>testing NMI watchdog ... OK.
>checking if image is initramfs... it is
>Freeing initrd memory: 956k freed
>NET: Registered protocol family 16
>ACPI: bus type pci registered
>PCI: Using configuration type 1
>ACPI: Subsystem revision 20060127
>ACPI: Interpreter enabled
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>Boot video device is 0000:01:00.0
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
>ACPI: Power Resource [ISAV] (on)
>ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
>ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
>ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
>ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
>ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *11
>ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *3
>ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *9
>ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *10
>ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *11
>ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *9
>ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
>ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
>ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled.
>ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *0, disabled.
>ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI init
>pnp: PnP ACPI: found 15 devices
>usbcore: registered new driver usbfs
>usbcore: registered new driver hub
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
>agpgart: Detected AGP bridge 0
>agpgart: Setting up Nforce3 AGP.
>agpgart: aperture base > 4G
>PCI-DMA: Disabling IOMMU.
>pnp: 00:0b: ioport range 0x480-0x487 has been reserved
>pnp: 00:0b: ioport range 0xd00-0xd07 has been reserved
>PCI: Bridge: 0000:00:0b.0
>  IO window: disabled.
>  MEM window: fca00000-feafffff
>  PREFETCH window: e4900000-f48fffff
>PCI: Bridge: 0000:00:0e.0
>  IO window: disabled.
>  MEM window: disabled.
>  PREFETCH window: disabled.
>PCI: Setting latency timer of device 0000:00:0e.0 to 64
>NET: Registered protocol family 2
>IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
>TCP established hash table entries: 16384 (order: 6, 393216 bytes)
>TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
>TCP: Hash tables configured (established 16384 bind 8192)
>TCP reno registered
>IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
>audit: initializing netlink socket (disabled)
>audit(1174739669.284:1): initialized
>Total HugeTLB memory allocated, 0
>VFS: Disk quotas dquot_6.5.1
>Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
>SELinux:  Registering netfilter hooks
>Initializing Cryptographic API
>ksign: Installing public key data
>Loading keyring
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>Real Time Clock Driver v1.12ac
>Linux agpgart interface v0.101 (c) Dave Jones
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
>NFORCE3-250: chipset revision 162
>NFORCE3-250: not 100% native mode: will probe irqs later
>NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
>NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
>NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
>    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
>    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
>Probing IDE interface ide0...
>hda: ST3802110A, ATA DISK drive
>hdb: WDC WD800JB-00JJA0, ATA DISK drive
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>Probing IDE interface ide1...
>hdc: SONY DVD RW AW-Q170A, ATAPI CD/DVD-ROM drive
>hdd: Seagate STT8000A, ATAPI TAPE drive
>ide1 at 0x170-0x177,0x376 on irq 15
>hda: max request size: 512KiB
>hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
>hda: cache flushes supported
> hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
>hdb: max request size: 128KiB
>hdb: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
>hdb: cache flushes supported
> hdb: hdb1 hdb2 hdb3
>hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66)
>Uniform CD-ROM driver Revision: 3.20
>ide-floppy driver 0.99.newide
>usbcore: registered new driver libusual
>usbcore: registered new driver hiddev
>usbcore: registered new driver usbhid
>drivers/usb/input/hid-core.c: v2.6:USB HID core driver
>PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
>PNP: PS/2 controller doesn't have AUX irq; using default 12
>serio: i8042 AUX port at 0x60,0x64 irq 12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>mice: PS/2 mouse device common for all mice
>TCP bic registered
>Initializing IPsec netlink socket
>NET: Registered protocol family 1
>NET: Registered protocol family 17
>powernow-k8: Power state transitions not supported
>ACPI wakeup devices: 
>PS2K UAR1 USB0  MAC USB1 USB2 P0P1 
>ACPI: (supports S0 S1 S3 S4 S5)
>Freeing unused kernel memory: 196k freed
>Write protecting the kernel read-only data: 433k
>input: AT Translated Set 2 keyboard as /class/input/input0
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs: mounted filesystem with ordered data mode.
>SELinux:  Disabled at runtime.
>SELinux:  Unregistering netfilter hooks
>audit(1174739673.411:2): selinux=0 auid=4294967295
>forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54.
>ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 22
>GSI 16 sharing vector 0xB1 and IRQ 16
>ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LKLN] -> GSI 22 (level, low) -> IRQ 16
>PCI: Setting latency timer of device 0000:00:05.0 to 64
>ide-tape: hdd <-> ht0: Seagate STT8000A rev 5.51
>ide-tape: hdd <-> ht0: 600KBps, 14*26kB buffer, 5850kB pipeline, 88ms tDSC, DMA
>ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
>eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:05.0
>ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
>GSI 17 sharing vector 0xB9 and IRQ 17
>ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 21 (level, low) -> IRQ 17
>PCI: Setting latency timer of device 0000:00:02.0 to 64
>ohci_hcd 0000:00:02.0: OHCI Host Controller
>ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
>ohci_hcd 0000:00:02.0: irq 17, io mem 0xfebfd000
>usb usb1: configuration #1 chosen from 1 choice
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 4 ports detected
>ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20
>GSI 18 sharing vector 0xC1 and IRQ 18
>ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 20 (level, low) -> IRQ 18
>PCI: Setting latency timer of device 0000:00:02.1 to 64
>ohci_hcd 0000:00:02.1: OHCI Host Controller
>ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
>ohci_hcd 0000:00:02.1: irq 18, io mem 0xfebfe000
>usb usb2: configuration #1 chosen from 1 choice
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 4 ports detected
>ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
>ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 22 (level, low) -> IRQ 16
>PCI: Setting latency timer of device 0000:00:02.2 to 64
>ehci_hcd 0000:00:02.2: EHCI Host Controller
>ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
>ehci_hcd 0000:00:02.2: debug port 1
>PCI: cache line size of 64 is not supported by device 0000:00:02.2
>ehci_hcd 0000:00:02.2: irq 16, io mem 0xfebffc00
>ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>usb usb3: configuration #1 chosen from 1 choice
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 8 ports detected
>i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
>i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5040
>ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 21
>ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 21 (level, low) -> IRQ 17
>PCI: Setting latency timer of device 0000:00:06.0 to 64
>usb 1-1: new low speed USB device using ohci_hcd and address 3
>usb 1-1: configuration #1 chosen from 1 choice
>input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
>input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-1
>intel8x0_measure_ac97_clock: measured 50594 usecs
>intel8x0: clocking to 46853
>Non-volatile memory driver v1.2
>Floppy drive(s): fd0 is 1.44M
>FDC 0 is a post-1991 82077
>parport: PnPBIOS parport detected.
>parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
>lp0: using parport0 (interrupt-driven).
>lp0: console ready
>NET: Registered protocol family 10
>lo: Disabled Privacy Extensions
>IPv6 over IPv4 tunneling driver
>ACPI: Power Button (FF) [PWRF]
>ACPI: Power Button (CM) [PWRB]
>EXT3 FS on hda7, internal journal
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on hda5, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on hdb1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on hda8, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on hdb3, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on hdb2, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>Adding 2096440k swap on /dev/hda6.  Priority:-1 extents:1 across:2096440k

Actions: View

Attachments on bug 234106: 151337 | 151338