Attachment 154449 Details for Bug 227281 – dmesg of a successful boot with usb stick plugged in

dmesg of a successful boot with usb stick plugged in

pass-dmesg.txt (text/plain), 30.36 KB, created by Allan Duncan on 2007-05-10 02:14:34 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Allan Duncan

Created: 2007-05-10 02:14:34 UTC

Size: 30.36 KB

patch

obsolete

>Linux version 2.6.20-1.3104.fc7 (brewbuilder@hs20-bc1-6.build.redhat.com) (gcc version 4.1.2 20070418 (Red Hat 4.1.2-10)) #1 SMP Sat Apr 21 22:20:43 EDT 2007
>BIOS-provided physical RAM map:
>sanitize start
>sanitize end
>copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
>copy_e820_map() type is E820_RAM
>copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
>copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
>copy_e820_map() start: 0000000000100000 size: 000000007fef0000 end: 000000007fff0000 type: 1
>copy_e820_map() type is E820_RAM
>copy_e820_map() start: 000000007fff0000 size: 0000000000003000 end: 000000007fff3000 type: 4
>copy_e820_map() start: 000000007fff3000 size: 000000000000d000 end: 0000000080000000 type: 3
>copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
>copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
>copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2
> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
> BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
> BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
>1151MB HIGHMEM available.
>896MB LOWMEM available.
>found SMP MP-table at 000f5790
>Using x86 segment limits to approximate NX protection
>Entering add_active_range(0, 0, 524272) 0 entries of 256 used
>Zone PFN ranges:
>  DMA             0 ->     4096
>  Normal       4096 ->   229376
>  HighMem    229376 ->   524272
>early_node_map[1] active PFN ranges
>    0:        0 ->   524272
>On node 0 totalpages: 524272
>  DMA zone: 52 pages used for memmap
>  DMA zone: 0 pages reserved
>  DMA zone: 4044 pages, LIFO batch:0
>  Normal zone: 2860 pages used for memmap
>  Normal zone: 222420 pages, LIFO batch:31
>  HighMem zone: 3743 pages used for memmap
>  HighMem zone: 291153 pages, LIFO batch:31
>DMI 2.3 present.
>Using APIC driver default
>ACPI: RSDP 000F70F0, 0014 (r0 Nvidia)
>ACPI: RSDT 7FFF3000, 002C (r1 Nvidia AWRDACPI 42302E31 AWRD  1010101)
>ACPI: FACP 7FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD  1010101)
>ACPI: DSDT 7FFF30C0, 4E35 (r1 NVIDIA AWRDACPI     1000 MSFT  100000C)
>ACPI: FACS 7FFF0000, 0040
>ACPI: APIC 7FFF7F00, 005A (r1 Nvidia AWRDACPI 42302E31 AWRD  1010101)
>Nvidia board detected. Ignoring ACPI timer override.
>If you got timer trouble try acpi_use_timer_override
>Nvidia board detected. Ignoring ACPI timer override.
>If you got timer trouble try acpi_use_timer_override
>ACPI: PM-Timer IO Port: 0x4008
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>Processor #0 6:10 APIC version 16
>ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>ACPI: BIOS IRQ0 pin2 override ignored.
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>ACPI: IRQ9 used by override.
>Enabling APIC mode:  Flat.  Using 1 I/O APICs
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
>Built 1 zonelists.  Total pages: 517617
>Kernel command line: initrd=initrd.img  ro quiet root=CDLABEL=Fedora-7-Test4-i386-Live rootfstype=iso9660 liveimg  BOOT_IMAGE=vmlinuz 
>mapped APIC to ffffd000 (fee00000)
>mapped IOAPIC to ffffc000 (fec00000)
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Initializing CPU#0
>CPU 0 irqstacks, hard=c079f000 soft=c077f000
>PID hash table entries: 4096 (order: 12, 16384 bytes)
>Detected 2083.382 MHz processor.
>Console: colour VGA+ 80x25
>Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
>... MAX_LOCKDEP_SUBCLASSES:    8
>... MAX_LOCK_DEPTH:          30
>... MAX_LOCKDEP_KEYS:        2048
>... CLASSHASH_SIZE:           1024
>... MAX_LOCKDEP_ENTRIES:     8192
>... MAX_LOCKDEP_CHAINS:      16384
>... CHAINHASH_SIZE:          8192
> memory used by lock dependency info: 1096 kB
> per task-struct memory footprint: 1200 bytes
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 2057500k/2097088k available (2150k kernel code, 38356k reserved, 1140k data, 248k init, 1179584k highmem)
>virtual kernel memory layout:
>    fixmap  : 0xffc56000 - 0xfffff000   (3748 kB)
>    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
>    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
>    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
>      .init : 0xc073c000 - 0xc077a000   ( 248 kB)
>      .data : 0xc06199fd - 0xc0736cb4   (1140 kB)
>      .text : 0xc0400000 - 0xc06199fd   (2150 kB)
>Checking if this processor honours the WP bit even in supervisor mode... Ok.
>Calibrating delay using timer specific routine.. 4169.05 BogoMIPS (lpj=2084526)
>Security Framework v1.0.0 initialized
>SELinux:  Initializing.
>SELinux:  Starting in permissive mode
>selinux_register_security:  Registering secondary module capability
>Capability LSM initialized as secondary
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>CPU: L2 Cache: 512K (64 bytes/line)
>CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000420 00000000 00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>Checking 'hlt' instruction... OK.
>SMP alternatives: switching to UP code
>Freeing SMP alternatives: 12k freed
>ACPI: Core revision 20070126
>CPU0: AMD Athlon(tm) XP 2800+ stepping 00
>Total of 1 processors activated (4169.05 BogoMIPS).
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
>Brought up 1 CPUs
>sizeof(vma)=84 bytes
>sizeof(page)=52 bytes
>sizeof(inode)=564 bytes
>sizeof(dentry)=156 bytes
>sizeof(ext3inode)=800 bytes
>sizeof(buffer_head)=56 bytes
>sizeof(skbuff)=176 bytes
>sizeof(task_struct)=2704 bytes
>Time:  1:37:05  Date: 04/10/107
>NET: Registered protocol family 16
>ACPI: bus type pci registered
>PCI: PCI BIOS revision 2.10 entry at 0xfb6f0, last bus=2
>PCI: Using configuration type 1
>Setting up standard PCI resources
>ACPI: Interpreter enabled
>ACPI: (supports S0 S1 S4 S5)
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>PCI: nForce2 C1 Halt Disconnect fixup
>0000:00:09.0: cannot adjust BAR0 (not I/O)
>0000:00:09.0: cannot adjust BAR1 (not I/O)
>0000:00:09.0: cannot adjust BAR2 (not I/O)
>0000:00:09.0: cannot adjust BAR3 (not I/O)
>Boot video device is 0000:02:00.0
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
>ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
>ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
>ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
>ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
>ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
>ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
>ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
>ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
>ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [APC1] (IRQs *16)
>ACPI: PCI Interrupt Link [APC2] (IRQs *17)
>ACPI: PCI Interrupt Link [APC3] (IRQs *18)
>ACPI: PCI Interrupt Link [APC4] (IRQs *19)
>ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
>ACPI: PCI Interrupt Link [APCF] (IRQs 20 21) *0
>ACPI: PCI Interrupt Link [APCG] (IRQs 20 21) *0
>ACPI: PCI Interrupt Link [APCH] (IRQs 20 21) *0, disabled.
>ACPI: PCI Interrupt Link [APCI] (IRQs 20 21) *0, disabled.
>ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21) *0, disabled.
>ACPI: PCI Interrupt Link [APCK] (IRQs 20 21) *0, disabled.
>ACPI: PCI Interrupt Link [APCS] (IRQs *23)
>ACPI: PCI Interrupt Link [APCL] (IRQs 20 21) *0
>ACPI: PCI Interrupt Link [APCM] (IRQs 20 21) *0, disabled.
>ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21) *0, disabled.
>ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21) *0, disabled.
>ACPI: PCI Interrupt Link [APSI] (IRQs 22) *0, disabled.
>ACPI: Power Resource [ISAV] (on)
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI init
>pnp: PnP ACPI: found 15 devices
>usbcore: registered new interface driver usbfs
>usbcore: registered new interface driver hub
>usbcore: registered new device driver usb
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
>NetLabel: Initializing
>NetLabel:  domain hash size = 128
>NetLabel:  protocols = UNLABELED CIPSOv4
>NetLabel:  unlabeled traffic allowed by default
>pnp: 00:00: ioport range 0x4000-0x407f has been reserved
>pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
>pnp: 00:00: ioport range 0x4400-0x447f has been reserved
>pnp: 00:00: ioport range 0x4480-0x44ff has been reserved
>pnp: 00:00: ioport range 0x4200-0x427f has been reserved
>pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
>Time: tsc clocksource has been installed.
>pnp: 00:01: ioport range 0x5000-0x503f has been reserved
>pnp: 00:01: ioport range 0x5100-0x513f has been reserved
>pnp: 00:02: iomem range 0xdc600-0xdffff has been reserved
>pnp: 00:02: iomem range 0xf0000-0xf7fff could not be reserved
>pnp: 00:02: iomem range 0xf8000-0xfbfff could not be reserved
>pnp: 00:02: iomem range 0xfc000-0xfffff could not be reserved
>PCI: Bridge: 0000:00:08.0
>  IO window: 8000-afff
>  MEM window: e7000000-e8ffffff
>  PREFETCH window: 88000000-880fffff
>PCI: Bridge: 0000:00:1e.0
>  IO window: disabled.
>  MEM window: e4000000-e6ffffff
>  PREFETCH window: d0000000-dfffffff
>PCI: Setting latency timer of device 0000:00:08.0 to 64
>NET: Registered protocol family 2
>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
>TCP established hash table entries: 65536 (order: 9, 2359296 bytes)
>TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
>TCP: Hash tables configured (established 65536 bind 65536)
>TCP reno registered
>checking if image is initramfs... it is
>Freeing initrd memory: 4241k freed
>apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
>apm: overridden by ACPI.
>audit: initializing netlink socket (disabled)
>audit(1178761024.324:1): initialized
>highmem bounce pool size: 64 pages
>Total HugeTLB memory allocated, 0
>VFS: Disk quotas dquot_6.5.1
>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>SELinux:  Registering netfilter hooks
>ksign: Installing public key data
>Loading keyring
>- Added public key 6581DC39491C512
>- User ID: Red Hat, Inc. (Kernel Module GPG key)
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>isapnp: Scanning for PnP cards...
>Switched to high resolution mode on CPU 0
>isapnp: No Plug & Play device found
>Real Time Clock Driver v1.12ac
>Non-volatile memory driver v1.2
>Linux agpgart interface v0.102 (c) Dave Jones
>agpgart: Detected NVIDIA nForce2 chipset
>agpgart: AGP aperture is 64M @ 0xe0000000
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
>input: Macintosh mouse button emulation as /class/input/input0
>usbcore: registered new interface driver libusual
>usbcore: registered new interface driver hiddev
>usbcore: registered new interface driver usbhid
>drivers/usb/input/hid-core.c: v2.6:USB HID core driver
>PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>serio: i8042 AUX port at 0x60,0x64 irq 12
>mice: PS/2 mouse device common for all mice
>input: AT Translated Set 2 keyboard as /class/input/input1
>TCP bic registered
>Initializing XFRM netlink socket
>NET: Registered protocol family 1
>NET: Registered protocol family 17
>powernow-k8: Processor cpuid 6a0 not supported
>Using IPI No-Shortcut mode
>  Magic number: 7:427:609
>Freeing unused kernel memory: 248k freed
>Write protecting the kernel read-only data: 846k
>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
>ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
>ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 16
>PCI: Setting latency timer of device 0000:00:02.0 to 64
>ohci_hcd 0000:00:02.0: OHCI Host Controller
>ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
>ohci_hcd 0000:00:02.0: irq 16, io mem 0xe9002000
>SCSI subsystem initialized
>libata version 2.20 loaded.
>usb usb1: configuration #1 chosen from 1 choice
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 4 ports detected
>ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
>ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IRQ 17
>PCI: Setting latency timer of device 0000:00:02.1 to 64
>ohci_hcd 0000:00:02.1: OHCI Host Controller
>ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
>ohci_hcd 0000:00:02.1: irq 17, io mem 0xe9003000
>usb usb2: configuration #1 chosen from 1 choice
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 4 ports detected
>input: ImPS/2 Generic Wheel Mouse as /class/input/input2
>pata_amd 0000:00:09.0: version 0.2.8
>PCI: Setting latency timer of device 0000:00:09.0 to 64
>ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
>ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
>scsi0 : pata_amd
>usb 2-2: new full speed USB device using ohci_hcd and address 2
>ATA: abnormal status 0x7F on port 0x000101f7
>ATA: abnormal status 0x7F on port 0x000101f7
>usb 2-2: configuration #1 chosen from 1 choice
>Initializing USB Mass Storage driver...
>scsi2 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 2
>usb-storage: waiting for device to settle before scanning
>usbcore: registered new interface driver usb-storage
>USB Mass Storage support registered.
>ata1.01: ATAPI, max UDMA/33
>ata1.01: configured for UDMA/33
>scsi1 : pata_amd
>ata2.00: ATAPI, max UDMA/66
>ata2.00: configured for UDMA/66
>scsi 0:0:1:0: CD-ROM            SONY     CD-ROM CDU5211   YYS7 PQ: 0 ANSI: 5
>scsi 1:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-111D 1.19 PQ: 0 ANSI: 5
>ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
>ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 16
>PCI: Setting latency timer of device 0000:00:02.2 to 64
>ehci_hcd 0000:00:02.2: EHCI Host Controller
>ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
>ehci_hcd 0000:00:02.2: debug port 1
>PCI: cache line size of 64 is not supported by device 0000:00:02.2
>ehci_hcd 0000:00:02.2: irq 16, io mem 0xe9004000
>ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>usb 2-2: USB disconnect, address 2
>usb usb3: configuration #1 chosen from 1 choice
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 8 ports detected
>sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
>Uniform CD-ROM driver Revision: 3.20
>sr 0:0:1:0: Attached scsi CD-ROM sr0
>sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
>sr 1:0:0:0: Attached scsi CD-ROM sr1
>pata_sil680 0000:01:07.0: version 0.4.5
>sil680: BA5_EN = 1 clock = 00
>sil680: BA5_EN = 1 clock = 10
>sil680: 133MHz clock.
>ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
>ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 18
>ata3: PATA max UDMA/133 cmd 0x00018000 ctl 0x00018402 bmdma 0x00019000 irq 18
>ata4: PATA max UDMA/133 cmd 0x00018800 ctl 0x00018c02 bmdma 0x00019008 irq 18
>scsi3 : pata_sil680
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 177415
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 177415
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 177415
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 177415
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 177415
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 177415
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 177415
>ata3.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
>ata3.00: ATA-7: ST3802110A, 3.AAJ, max UDMA/100
>ata3.00: 156301488 sectors, multi 16: LBA48 
>usb 3-4: new high speed USB device using ehci_hcd and address 2
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 177415
>ata3.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
>ata3.00: configured for UDMA/100
>scsi4 : pata_sil680
>usb 3-4: configuration #1 chosen from 1 choice
>scsi5 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 2
>usb-storage: waiting for device to settle before scanning
>ata4.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
>ata4.00: ATA-6: WDC WD800JB-00DUA3, 75.13B75, max UDMA/100
>ata4.00: 156301488 sectors, multi 16: LBA48 
>ata4.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
>ata4.00: configured for UDMA/100
>scsi 3:0:0:0: Direct-Access     ATA      ST3802110A       3.AA PQ: 0 ANSI: 5
>scsi 4:0:0:0: Direct-Access     ATA      WDC WD800JB-00DU 75.1 PQ: 0 ANSI: 5
>SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
>sda: Write Protect is off
>sda: Mode Sense: 00 3a 00 00
>SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
>sda: Write Protect is off
>sda: Mode Sense: 00 3a 00 00
>SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: sda1 sda2 sda3 sda4
>sd 3:0:0:0: Attached scsi disk sda
>SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
>sdb: Write Protect is off
>sdb: Mode Sense: 00 3a 00 00
>SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
>sdb: Write Protect is off
>sdb: Mode Sense: 00 3a 00 00
>SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdb: sdb1 < sdb5 >
>sd 4:0:0:0: Attached scsi disk sdb
>ISO 9660 Extensions: Microsoft Joliet Level 3
>Unable to load NLS charset utf8
>Unable to load NLS charset utf8
>ISO 9660 Extensions: RRIP_1991A
>loop: loaded (max 128 devices)
>device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
>squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on dm-0, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>audit(1178761031.323:2): enforcing=1 old_enforcing=0 auid=4294967295
>security:  3 users, 6 roles, 1801 types, 76 bools, 1 sens, 1024 cats
>security:  60 classes, 65047 rules
>SELinux:  Completing initialization.
>SELinux:  Setting up existing superblocks.
>SELinux: initialized (dev dm-0, type ext3), uses xattr
>inode_doinit_with_dentry:  no dentry for dev=dm-0 ino=360883
>inode_doinit_with_dentry:  no dentry for dev=dm-0 ino=360881
>inode_doinit_with_dentry:  no dentry for dev=dm-0 ino=360878
>SELinux: initialized (dev loop120, type squashfs), not configured for labeling
>SELinux: initialized (dev sr0, type iso9660), uses genfs_contexts
>SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
>SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
>SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
>SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
>SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
>SELinux: initialized (dev devpts, type devpts), uses transition SIDs
>SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
>SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
>SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
>SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
>SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
>SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
>SELinux: initialized (dev proc, type proc), uses genfs_contexts
>SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
>SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
>SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
>audit(1178761032.323:3): policy loaded auid=4294967295
>usb-storage: device scan complete
>scsi 5:0:0:0: Direct-Access     Generic  USB Flash Disk   0.00 PQ: 0 ANSI: 2
>SCSI device sdc: 2048000 512-byte hdwr sectors (1049 MB)
>sdc: Write Protect is off
>sdc: Mode Sense: 00 00 00 00
>sdc: assuming drive cache: write through
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>SCSI device sdc: 2048000 512-byte hdwr sectors (1049 MB)
>sdc: Write Protect is off
>sdc: Mode Sense: 00 00 00 00
>sdc: assuming drive cache: write through
> sdc: sdc1
>sd 5:0:0:0: Attached scsi removable disk sdc
>sr 0:0:1:0: Attached scsi generic sg0 type 5
>sr 1:0:0:0: Attached scsi generic sg1 type 5
>sd 3:0:0:0: Attached scsi generic sg2 type 0
>sd 4:0:0:0: Attached scsi generic sg3 type 0
>sd 5:0:0:0: Attached scsi generic sg4 type 0
>Floppy drive(s): fd0 is 1.44M, fd1 is 1.44M
>FDC 0 is a post-1991 82077
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 354830
>Buffer I/O error on device sr0, logical block 354831
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 354830
>end_request: I/O error, dev sr0, sector 1419324
>Buffer I/O error on device sr0, logical block 354831
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 354830
>Buffer I/O error on device sr0, logical block 354831
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>Buffer I/O error on device sr0, logical block 354830
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
>ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 19
>scsi6 : AdvanSys SCSI 3.3K: PCI Ultra: IO 0x9C00-0x9C0F, IRQ 0x13
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>printk: 3 messages suppressed.
>Buffer I/O error on device sr0, logical block 354830
>i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
>i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100
>input: PC Speaker as /class/input/input3
>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
>8139cp 0000:01:0b.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
>8139cp 0000:01:0b.0: Try the "8139too" driver instead.
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
>ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 20
>8139too Fast Ethernet driver 0.9.28
>fw_ohci: Added fw-ohci device 0000:01:08.0, OHCI version 1.0
>ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 20
>eth0: RealTek RTL8139 at 0xf8b1c000, 00:0f:ea:0e:c9:48, IRQ 20
>eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
>parport: PnPBIOS parport detected.
>parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
>rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
>rtc_cmos: probe of 00:06 failed with error -16
>sr 0:0:1:0: SCSI error: return code = 0x08000002
>sr0: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error
>end_request: I/O error, dev sr0, sector 1419320
>fw_core: created new fw device fw0 (0 config rom retries)
>ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
>ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 21
>lp0: using parport0 (interrupt-driven).
>lp0: console ready
>sonypi: Sony Programmable I/O Controller Driver v1.26.
>No dock devices found.
>input: Power Button (FF) as /class/input/input4
>ACPI: Power Button (FF) [PWRF]
>input: Power Button (CM) as /class/input/input5
>ACPI: Power Button (CM) [PWRB]
>ibm_acpi: ec object not found
>device-mapper: multipath: version 1.0.5 loaded
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>EXT3 FS on dm-0, internal journal
>SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
>audit(1178775497.372:4): audit_pid=2864 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
>NET: Registered protocol family 10
>lo: Disabled Privacy Extensions
>Mobile IPv6
>SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
>Bluetooth: Core ver 2.11
>NET: Registered protocol family 31
>Bluetooth: HCI device and connection manager initialized
>Bluetooth: HCI socket layer initialized
>Bluetooth: L2CAP ver 2.8
>Bluetooth: L2CAP socket layer initialized
>Bluetooth: RFCOMM socket layer initialized
>Bluetooth: RFCOMM TTY layer initialized
>Bluetooth: RFCOMM ver 1.8
>Bluetooth: HIDP (Human Interface Emulation) ver 1.2
>SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
>SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
>SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
>ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 18
>eth0: no IPv6 routers present
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>sd 5:0:0:0: ioctl_internal_command return code = 8000002
>   : Current: sense key: No Sense
>    Additional sense: No additional sense information
>SELinux: initialized (dev sdc1, type vfat), uses genfs_contexts

Actions: View

Attachments on bug 227281: 149602 | 150007 | 154448 | 154449