Attachment 157221 Details for Bug 244563 – dmesg output when attaching usb2 device with "noapic irqpoll"

dmesg output when attaching usb2 device with "noapic irqpoll"

usb2.txt (text/plain), 2.88 KB, created by Jesus Salvo on 2007-06-17 12:32:36 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Jesus Salvo

Created: 2007-06-17 12:32:36 UTC

Size: 2.88 KB

patch

obsolete

>usb 2-2: new high speed USB device using ehci_hcd and address 5
>usb 2-2: device not accepting address 5, error -71
>usb 2-2: new high speed USB device using ehci_hcd and address 6
>usb 2-2: configuration #1 chosen from 1 choice
>usb 2-2: can't set config #1, error -71
>usb 2-2: USB disconnect, address 6
>usb 2-2: new high speed USB device using ehci_hcd and address 7
>usb 2-2: configuration #1 chosen from 1 choice
>Initializing USB Mass Storage driver...
>scsi4 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 7
>usb-storage: waiting for device to settle before scanning
>usbcore: registered new interface driver usb-storage
>USB Mass Storage support registered.
>usb 2-2: USB disconnect, address 7
>usb 2-2: new high speed USB device using ehci_hcd and address 8
>usb 2-2: configuration #1 chosen from 1 choice
>scsi5 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 8
>usb-storage: waiting for device to settle before scanning
>usb-storage: device scan complete
>scsi 5:0:0:0: Direct-Access              WDC WD800JB-00ET 77.0 PQ: 0 ANSI: 0 CCS
>SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
>sdb: test WP failed, assume Write Enabled
>sdb: assuming drive cache: write through
>SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
>sdb: test WP failed, assume Write Enabled
>sdb: assuming drive cache: write through
> sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 >
>sd 5:0:0:0: Attached scsi disk sdb
>sd 5:0:0:0: Attached scsi generic sg2 type 0
>usb 2-2: reset high speed USB device using ehci_hcd and address 8
>hub 2-0:1.0: Cannot enable port 2.  Maybe the USB cable is bad?
>usb 2-2: reset high speed USB device using ehci_hcd and address 8
>ip6_tables: (C) 2000-2006 Netfilter Core Team
>ACPI: PCI Interrupt Link [LK3E] enabled at IRQ 11
>ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LK3E] -> GSI 11 (level, low) -> IRQ 11
>usb 2-2: USB disconnect, address 8
>usb 1-2: new full speed USB device using ohci_hcd and address 5
>usb 1-2: not running at top speed; connect to a high speed hub
>usb 1-2: configuration #1 chosen from 1 choice
>scsi6 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 5
>usb-storage: waiting for device to settle before scanning
>usb-storage: device scan complete
>scsi 6:0:0:0: Direct-Access              WDC WD800JB-00ET 77.0 PQ: 0 ANSI: 0 CCS
>SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
>sdb: test WP failed, assume Write Enabled
>sdb: assuming drive cache: write through
>SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
>sdb: test WP failed, assume Write Enabled
>sdb: assuming drive cache: write through
> sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 >
>sd 6:0:0:0: Attached scsi disk sdb
>sd 6:0:0:0: Attached scsi generic sg2 type 0
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sdb7, internal journal
>EXT3-fs: recovery complete.
>EXT3-fs: mounted filesystem with ordered data mode.

Actions: View

Attachments on bug 244563: 157217 | 157218 | 157221