Attachment 158037 Details for Bug 245864 – requested apcupsd.conf

requested apcupsd.conf

apcupsd.conf (text/plain), 11.51 KB, created by Jay Goodman on 2007-06-27 18:36:04 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Jay Goodman

Created: 2007-06-27 18:36:04 UTC

Size: 11.51 KB

patch

obsolete

>## apcupsd.conf v1.1 ##
># 
>#  for apcupsd release 3.14.1 (04 May 2007) - redhat
>#
># "apcupsd" POSIX config file
>
>#
># ========= General configuration parameters ============
>#
>
># UPSNAME xxx
>#   Use this to give your UPS a name in log files and such. This
>#   is particulary useful if you have multiple UPSes. This does not
>#   set the EEPROM. It should be 8 characters or less.
>#UPSNAME
>
># UPSCABLE <cable>
>#   Defines the type of cable connecting the UPS to your computer.
>#
>#   Possible generic choices for <cable> are:
>#     simple, smart, ether, usb
>#
>#   Or a specific cable model number may be used:
>#     940-0119A, 940-0127A, 940-0128A, 940-0020B,
>#     940-0020C, 940-0023A, 940-0024B, 940-0024C,
>#     940-1524C, 940-0024G, 940-0095A, 940-0095B,
>#     940-0095C, M-04-02-2000
>#
>UPSCABLE usb
>
># To get apcupsd to work, in addition to defining the cable
># above, you must also define a UPSTYPE, which corresponds to
># the type of UPS you have (see the Description for more details).
># You must also specify a DEVICE, sometimes referred to as a port.
># For USB UPSes, please leave the DEVICE directive blank. For
># other UPS types, you must specify an appropriate port or address.
>#
># UPSTYPE   DEVICE           Description
># apcsmart  /dev/tty**       Newer serial character device,
>#                            appropriate for SmartUPS models using
>#                            a serial cable (not USB).
>#
># usb       <BLANK>          Most new UPSes are USB. A blank DEVICE
>#                            setting enables autodetection, which is
>#                            the best choice for most installations.
>#
># net       hostname:port    Network link to a master apcupsd
>#                            through apcupsd's Network Information
>#                            Server. This is used if you don't have
>#                            a UPS directly connected to your computer.
>#
># snmp      hostname:port:vendor:community
>#                            SNMP Network link to an SNMP-enabled
>#                            UPS device. Vendor is the MIB used by
>#                            the UPS device: can be "APC", "APC_NOTRAP"
>#                            or "RFC" where APC is the powernet MIB,
>#                            "APC_NOTRAP" is powernet with SNMP trap
>#                            catching disabled, and RFC is the IETF's 
>#                            rfc1628 UPS-MIB. You usually want "APC".
>#                            Port is usually 161. Community is usually
>#                            "private".
>#
># dumb      /dev/tty**       Old serial character device for use 
>#                            with simple-signaling UPSes.
>#
># pcnet    ipaddr:username:passphrase
>#                            PowerChute Network Shutdown protocol
>#                            which can be used as an alternative to SNMP
>#                            with AP9617 family of smart slot cards.
>#                            ipaddr is the IP address of the UPS mgmt
>#                            card. username and passphrase are the
>#                            credentials for which the card has been
>#                            configured.
>#
>UPSTYPE usb
>DEVICE 
>
>
># LOCKFILE <path to lockfile>
>#   Path for device lock file. Not used on Win32.
>LOCKFILE /var/lock
>
># SCRIPTDIR <path to script directory>
>#   Directory in which apccontrol and event scripts are located.
>SCRIPTDIR /etc/apcupsd
>
># PWRFAILDIR <path to powerfail directory>
>#   Directory in which to write the powerfail flag file. This file
>#   is created when apcupsd initiates a system shutdown and is
>#   checked in the OS halt scripts to determine if a killpower
>#   (turning off UPS output power) is required.
>PWRFAILDIR /etc/apcupsd
>
># NOLOGINDIR <path to nologin directory>
>#   Directory in which to write the nologin file. The existence
>#   of this flag file tells the OS to disallow new logins.
>NOLOGINDIR /etc
>
>
>#
># ======== Configuration parameters used during power failures ==========
>#
>
># The ONBATTERYDELAY is the time in seconds from when a power failure
>#   is detected until we react to it with an onbattery event.
>#
>#   This means that, apccontrol will be called with the powerout argument
>#   immediately when a power failure is detected.  However, the
>#   onbattery argument is passed to apccontrol only after the 
>#   ONBATTERYDELAY time.  If you don't want to be annoyed by short
>#   powerfailures, make sure that apccontrol powerout does nothing
>#   i.e. comment out the wall.
>ONBATTERYDELAY 6
>
># 
># Note: BATTERYLEVEL, MINUTES, and TIMEOUT work in conjunction, so
># the first that occurs will cause the initation of a shutdown.
>#
>
># If during a power failure, the remaining battery percentage
># (as reported by the UPS) is below or equal to BATTERYLEVEL, 
># apcupsd will initiate a system shutdown.
>BATTERYLEVEL 4
>
># If during a power failure, the remaining runtime in minutes 
># (as calculated internally by the UPS) is below or equal to MINUTES,
># apcupsd, will initiate a system shutdown.
>MINUTES 2
>
># If during a power failure, the UPS has run on batteries for TIMEOUT
># many seconds or longer, apcupsd will initiate a system shutdown.
># A value of 0 disables this timer.
>#
>#  Note, if you have a Smart UPS, you will most likely want to disable
>#    this timer by setting it to zero. That way, you UPS will continue
>#    on batteries until either the % charge remaing drops to or below BATTERYLEVEL,
>#    or the remaining battery runtime drops to or below MINUTES.  Of course,
>#    if you are testing, setting this to 60 causes a quick system shutdown
>#    if you pull the power plug.   
>#  If you have an older dumb UPS, you will want to set this to less than
>#    the time you know you can run on batteries.
>TIMEOUT 0
>
>#  Time in seconds between annoying users to signoff prior to
>#  system shutdown. 0 disables.
>ANNOY 120
>
># Initial delay after power failure before warning users to get
># off the system.
>ANNOYDELAY 60
>
># The condition which determines when users are prevented from
># logging in during a power failure.
># NOLOGON <string> [ disable | timeout | percent | minutes | always ]
>NOLOGON disable
>
># If KILLDELAY is non-zero, apcupsd will continue running after a
># shutdown has been requested, and after the specified time in
># seconds attempt to kill the power. This is for use on systems
># where apcupsd cannot regain control after a shutdown.
># KILLDELAY <seconds>  0 disables
>KILLDELAY 0
>
>#
># ==== Configuration statements for Network Information Server ====
>#
>
># NETSERVER [ on | off ] on enables, off disables the network
>#  information server. If netstatus is on, a network information
>#  server process will be started for serving the STATUS and
>#  EVENT data over the network (used by CGI programs).
>NETSERVER on
>
># NISIP <dotted notation ip address>
>#  IP address on which NIS server will listen for incoming connections.
>#  This is useful if your server is multi-homed (has more than one
>#  network interface and IP address). Default value is 0.0.0.0 which
>#  means any incoming request will be serviced. Alternatively, you can
>#  configure this setting to any specific IP address of your server and 
>#  NIS will listen for connections only on that interface. Use the
>#  loopback address (127.0.0.1) to accept connections only from the
>#  local machine.
>NISIP 0.0.0.0
>
># NISPORT <port> default is 3551 as registered with the IANA
>#  port to use for sending STATUS and EVENTS data over the network.
>#  It is not used unless NETSERVER is on. If you change this port,
>#  you will need to change the corresponding value in the cgi directory
>#  and rebuild the cgi programs.
>NISPORT 3551
>
># If you want the last few EVENTS to be available over the network
># by the network information server, you must define an EVENTSFILE.
>EVENTSFILE /var/log/apcupsd.events
>
># EVENTSFILEMAX <kilobytes>
>#  By default, the size of the EVENTSFILE will be not be allowed to exceed
>#  10 kilobytes.  When the file grows beyond this limit, older EVENTS will
>#  be removed from the beginning of the file (first in first out).  The
>#  parameter EVENTSFILEMAX can be set to a different kilobyte value, or set
>#  to zero to allow the EVENTSFILE to grow without limit.
>EVENTSFILEMAX 10
>
>#
># ========== Configuration statements used if sharing =============
>#            a UPS with more than one machine
>
># NETTIME <int>
>#   Interval (in seconds) at which the NIS client polls the server.
>#   Used only when this apcupsd is a network client (UPSTYPE net).
>#NETTIME 60
>
>#
># Remaining items are for ShareUPS (APC expansion card) ONLY
>#
>
># UPSCLASS [ standalone | shareslave | sharemaster ]
>#   Normally standalone unless you share an UPS using an APC ShareUPS
>#   card.
>UPSCLASS standalone
>
># UPSMODE [ disable | share ]
>#   Normally disable unless you share an UPS using an APC ShareUPS card.
>UPSMODE disable
>
>#
># ===== Configuration statements to control apcupsd system logging ========
>#
>
># Time interval in seconds between writing the STATUS file; 0 disables
>STATTIME 0
>
># Location of STATUS file (written to only if STATTIME is non-zero)
>STATFILE /var/log/apcupsd.status
>
># LOGSTATS [ on | off ] on enables, off disables
># Note! This generates a lot of output, so if         
>#       you turn this on, be sure that the
>#       file defined in syslog.conf for LOG_NOTICE is a named pipe.
>#  You probably do not want this on.
>LOGSTATS off
>
># Time interval in seconds between writing the DATA records to
>#   the log file. 0 disables.
>DATATIME 0
>
># FACILITY defines the logging facility (class) for logging to syslog. 
>#          If not specified, it defaults to "daemon". This is useful 
>#          if you want to separate the data logged by apcupsd from other
>#          programs.
>#FACILITY DAEMON
>
>#
># ========== Configuration statements used in updating the UPS EPROM =========
>#
>
>#
># These statements are used only by apctest when choosing "Set EEPROM with conf
># file values" from the EEPROM menu. THESE STATEMENTS HAVE NO EFFECT ON APCUPSD.
>#
>
># UPS name, max 8 characters 
>#UPSNAME UPS_IDEN
>
># Battery date - 8 characters
>#BATTDATE mm/dd/yy
>
># Sensitivity to line voltage quality (H cause faster transfer to batteries)  
># SENSITIVITY H M L        (default = H)
>#SENSITIVITY H
>
># UPS delay after power return (seconds)
># WAKEUP 000 060 180 300   (default = 0)
>#WAKEUP 60
>
># UPS Grace period after request to power off (seconds)
># SLEEP 020 180 300 600    (default = 20)
>#SLEEP 180
>
># Low line voltage causing transfer to batteries
># The permitted values depend on your model as defined by last letter 
>#  of FIRMWARE or APCMODEL. Some representative values are:
>#    D 106 103 100 097
>#    M 177 172 168 182
>#    A 092 090 088 086
>#    I 208 204 200 196     (default = 0 => not valid)
>#LOTRANSFER  208
>
># High line voltage causing transfer to batteries
># The permitted values depend on your model as defined by last letter 
>#  of FIRMWARE or APCMODEL. Some representative values are:
>#    D 127 130 133 136
>#    M 229 234 239 224
>#    A 108 110 112 114
>#    I 253 257 261 265     (default = 0 => not valid)
>#HITRANSFER 253
>
># Battery charge needed to restore power
># RETURNCHARGE 00 15 50 90 (default = 15)
>RETURNCHARGE 5
>
># Alarm delay 
># 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low battery, N = never
># BEEPSTATE 0 T L N        (default = 0)
>#BEEPSTATE T
>
># Low battery warning delay in minutes
># LOWBATT 02 05 07 10      (default = 02)
>#LOWBATT 2
>
># UPS Output voltage when running on batteries
># The permitted values depend on your model as defined by last letter 
>#  of FIRMWARE or APCMODEL. Some representative values are:
>#    D 115
>#    M 208
>#    A 100
>#    I 230 240 220 225     (default = 0 => not valid)
>#OUTPUTVOLTS 230
>
># Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on
># SELFTEST 336 168 ON OFF  (default = 336)
>#SELFTEST 336

Actions: View

Attachments on bug 245864: 158037 | 158041 | 158060