Attachment 267841 Details for Bug 397521 – dmesg and lspci -vvv output

dmesg and lspci -vvv output

dmesg+lspci-vvv.txt (text/plain), 51.05 KB, created by Daniel C Weeks on 2007-11-24 00:42:58 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Daniel C Weeks

Created: 2007-11-24 00:42:58 UTC

Size: 51.05 KB

patch

obsolete

>Linux version 2.6.23.1-49.fc8 (kojibuilder@xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Thu Nov 8 21:41:26 EST 2007
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
> BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
> BIOS-e820: 000000003fef0000 - 000000003fef3000 (ACPI NVS)
> BIOS-e820: 000000003fef3000 - 000000003ff00000 (ACPI data)
> BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
>126MB HIGHMEM available.
>896MB LOWMEM available.
>found SMP MP-table at 000f36a0
>Using x86 segment limits to approximate NX protection
>Entering add_active_range(0, 0, 261872) 0 entries of 256 used
>Zone PFN ranges:
>  DMA             0 ->     4096
>  Normal       4096 ->   229376
>  HighMem    229376 ->   261872
>Movable zone start PFN for each node
>early_node_map[1] active PFN ranges
>    0:        0 ->   261872
>On node 0 totalpages: 261872
>  DMA zone: 32 pages used for memmap
>  DMA zone: 0 pages reserved
>  DMA zone: 4064 pages, LIFO batch:0
>  Normal zone: 1760 pages used for memmap
>  Normal zone: 223520 pages, LIFO batch:31
>  HighMem zone: 253 pages used for memmap
>  HighMem zone: 32243 pages, LIFO batch:7
>  Movable zone: 0 pages used for memmap
>DMI 2.3 present.
>Using APIC driver default
>ACPI: RSDP 000F77D0, 0014 (r0 VIAK8T)
>ACPI: RSDT 3FEF3040, 0034 (r1 VIAK8T AWRDACPI 42302E31 AWRD        0)
>ACPI: FACP 3FEF30C0, 0074 (r1 VIAK8T AWRDACPI 42302E31 AWRD        0)
>ACPI: DSDT 3FEF3180, 4F8A (r1 VIAK8T AWRDACPI     1000 MSFT  100000E)
>ACPI: FACS 3FEF0000, 0040
>ACPI: BOOT 3FEF8180, 0028 (r1 VIAK8T AWRDACPI 42302E31 AWRD        0)
>ACPI: SSDT 3FEF82C0, 0188 (r1 PTLTD  POWERNOW        1  LTP        1)
>ACPI: APIC 3FEF8200, 0068 (r1 VIAK8T AWRDACPI 42302E31 AWRD        0)
>ACPI: PM-Timer IO Port: 0x4008
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>Processor #0 15:3 APIC version 16
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
>Processor #1 15:3 APIC version 16
>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
>ACPI: IRQ0 used by override.
>ACPI: IRQ2 used by override.
>ACPI: IRQ9 used by override.
>Enabling APIC mode:  Flat.  Using 1 I/O APICs
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 40000000 (gap: 3ff00000:bed00000)
>swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
>swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
>swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
>Built 1 zonelists in Zone order.  Total pages: 259827
>Kernel command line: ro root=LABEL=/ 
>mapped APIC to ffffb000 (fee00000)
>mapped IOAPIC to ffffa000 (fec00000)
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Initializing CPU#0
>CPU 0 irqstacks, hard=c07a8000 soft=c0788000
>PID hash table entries: 4096 (order: 12, 16384 bytes)
>Detected 2043.271 MHz processor.
>Console: colour VGA+ 80x25
>console [tty0] enabled
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 1030300k/1047488k available (2184k kernel code, 16436k reserved, 1116k data, 280k init, 129984k highmem)
>virtual kernel memory layout:
>    fixmap  : 0xffc53000 - 0xfffff000   (3760 kB)
>    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
>    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
>    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
>      .init : 0xc073f000 - 0xc0785000   ( 280 kB)
>      .data : 0xc0622165 - 0xc0739544   (1116 kB)
>      .text : 0xc0400000 - 0xc0622165   (2184 kB)
>Checking if this processor honours the WP bit even in supervisor mode... Ok.
>SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
>Calibrating delay using timer specific routine.. 4089.28 BogoMIPS (lpj=2044640)
>Security Framework v1.0.0 initialized
>SELinux:  Initializing.
>SELinux:  Starting in permissive mode
>selinux_register_security:  Registering secondary module capability
>Capability LSM initialized as secondary
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 00000000
>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>CPU: L2 Cache: 512K (64 bytes/line)
>CPU 0(2) -> Core 0
>CPU: After all inits, caps: 178bf3ff e3d3fbff 00000000 00000410 00000001 00000000 00000003 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>Compat vDSO mapped to ffffe000.
>Checking 'hlt' instruction... OK.
>SMP alternatives: switching to UP code
>ACPI: Core revision 20070126
>CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
>SMP alternatives: switching to SMP code
>Booting processor 1/1 eip 3000
>CPU 1 irqstacks, hard=c07a9000 soft=c0789000
>Initializing CPU#1
>Calibrating delay using timer specific routine.. 4085.62 BogoMIPS (lpj=2042811)
>CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 00000000
>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>CPU: L2 Cache: 512K (64 bytes/line)
>CPU 1(2) -> Core 1
>CPU: After all inits, caps: 178bf3ff e3d3fbff 00000000 00000410 00000001 00000000 00000003 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#1.
>CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
>Total of 2 processors activated (8174.90 BogoMIPS).
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
>Brought up 2 CPUs
>sizeof(vma)=84 bytes
>sizeof(page)=32 bytes
>sizeof(inode)=336 bytes
>sizeof(dentry)=132 bytes
>sizeof(ext3inode)=488 bytes
>sizeof(buffer_head)=56 bytes
>sizeof(skbuff)=180 bytes
>sizeof(task_struct)=1552 bytes
>Booting paravirtualized kernel on bare hardware
>Time: 15:56:29  Date: 11/23/07
>NET: Registered protocol family 16
>No dock devices found.
>ACPI: bus type pci registered
>PCI: PCI BIOS revision 2.10 entry at 0xfa090, last bus=1
>PCI: Using configuration type 1
>Setting up standard PCI resources
>ACPI: EC: Look up EC in DSDT
>ACPI: Interpreter enabled
>ACPI: (supports S0 S3 S4 S5)
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>Force enabled HPET at base address 0xfed00000
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12)
>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12)
>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 *10 11 12)
>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
>ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *5
>ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
>ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
>ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
>ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
>ACPI: PCI Interrupt Link [ALKD] (IRQs *23), disabled.
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI init
>ACPI: bus type pnp registered
>pnp: PnP ACPI: found 11 devices
>ACPI: ACPI bus type pnp unregistered
>usbcore: registered new interface driver usbfs
>usbcore: registered new interface driver hub
>usbcore: registered new device driver usb
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
>NetLabel: Initializing
>NetLabel:  domain hash size = 128
>NetLabel:  protocols = UNLABELED CIPSOv4
>NetLabel:  unlabeled traffic allowed by default
>hpet clockevent registered
>hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
>hpet0: 3 32-bit timers, 14318180 Hz
>Time: hpet clocksource has been installed.
>Switched to high resolution mode on CPU 0
>Switched to high resolution mode on CPU 1
>pnp: 00:00: iomem range 0xd0000-0xd3fff has been reserved
>pnp: 00:00: iomem range 0xdc800-0xdffff has been reserved
>pnp: 00:00: iomem range 0xf0000-0xfbfff could not be reserved
>pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
>pnp: 00:02: ioport range 0x4000-0x407f has been reserved
>pnp: 00:02: ioport range 0x5000-0x500f has been reserved
>PCI: Bridge: 0000:00:01.0
>  IO window: disabled.
>  MEM window: f0000000-f2ffffff
>  PREFETCH window: e0000000-efffffff
>PCI: Setting latency timer of device 0000:00:01.0 to 64
>NET: Registered protocol family 2
>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
>TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>TCP reno registered
>checking if image is initramfs... it is
>Freeing initrd memory: 2930k freed
>Simple Boot Flag at 0x37 set to 0x1
>apm: BIOS not found.
>audit: initializing netlink socket (disabled)
>audit(1195833388.538:1): initialized
>highmem bounce pool size: 64 pages
>Total HugeTLB memory allocated, 0
>VFS: Disk quotas dquot_6.5.1
>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>SELinux:  Registering netfilter hooks
>ksign: Installing public key data
>Loading keyring
>- Added public key D5E5FC8EDCF186B6
>- User ID: Red Hat, Inc. (Kernel Module GPG key)
>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>PCI: VIA PCI bridge detected. Disabling DAC.
>Boot video device is 0000:01:00.0
>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>isapnp: Scanning for PnP cards...
>isapnp: No Plug & Play device found
>Real Time Clock Driver v1.12ac
>Non-volatile memory driver v1.2
>Linux agpgart interface v0.102
>agpgart: Detected AGP bridge 0
>agpgart: AGP aperture is 256M @ 0xd0000000
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
>input: Macintosh mouse button emulation as /class/input/input0
>PNP: No PS/2 controller found. Probing ports directly.
>serio: i8042 KBD port at 0x60,0x64 irq 1
>serio: i8042 AUX port at 0x60,0x64 irq 12
>mice: PS/2 mouse device common for all mice
>cpuidle: using governor menu
>usbcore: registered new interface driver hiddev
>usbcore: registered new interface driver usbhid
>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
>TCP cubic registered
>Initializing XFRM netlink socket
>NET: Registered protocol family 1
>NET: Registered protocol family 17
>powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ processors (2 cpu cores) (version 2.00.00)
>powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x8
>powernow-k8:    1 : fid 0xa (1800 MHz), vid 0xa
>powernow-k8:    2 : fid 0x2 (1000 MHz), vid 0x12
>Using IPI No-Shortcut mode
>  Magic number: 15:241:943
>  hash matches device tty0
>  hash matches device console
>Freeing unused kernel memory: 280k freed
>Write protecting the kernel read-only data: 845k
>ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 16
>ehci_hcd 0000:00:10.4: EHCI Host Controller
>ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
>ehci_hcd 0000:00:10.4: irq 16, io mem 0xf3085000
>ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>usb usb1: configuration #1 chosen from 1 choice
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 8 ports detected
>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
>USB Universal Host Controller Interface driver v3.0
>ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 16
>uhci_hcd 0000:00:10.0: UHCI Host Controller
>uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
>uhci_hcd 0000:00:10.0: irq 16, io base 0x0000e900
>usb usb2: configuration #1 chosen from 1 choice
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 16
>uhci_hcd 0000:00:10.1: UHCI Host Controller
>uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
>uhci_hcd 0000:00:10.1: irq 16, io base 0x0000ea00
>usb usb3: configuration #1 chosen from 1 choice
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 16
>uhci_hcd 0000:00:10.2: UHCI Host Controller
>uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
>uhci_hcd 0000:00:10.2: irq 16, io base 0x0000eb00
>usb usb4: configuration #1 chosen from 1 choice
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 16
>uhci_hcd 0000:00:10.3: UHCI Host Controller
>uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
>uhci_hcd 0000:00:10.3: irq 16, io base 0x0000ec00
>usb usb5: configuration #1 chosen from 1 choice
>hub 5-0:1.0: USB hub found
>hub 5-0:1.0: 2 ports detected
>SCSI subsystem initialized
>libata version 2.21 loaded.
>sata_via 0000:00:0f.0: version 2.3
>ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
>ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 17
>sata_via 0000:00:0f.0: routed to hard irq line 11
>scsi0 : sata_via
>scsi1 : sata_via
>ata1: SATA max UDMA/133 cmd 0x0001e200 ctl 0x0001e302 bmdma 0x0001e600 irq 17
>ata2: SATA max UDMA/133 cmd 0x0001e400 ctl 0x0001e502 bmdma 0x0001e608 irq 17
>usb 1-3: new high speed USB device using ehci_hcd and address 4
>usb 1-3: configuration #1 chosen from 1 choice
>hub 1-3:1.0: USB hub found
>hub 1-3:1.0: 4 ports detected
>ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
>ata1.00: ATA-7: HDT722525DLA380, V44OA80A, max UDMA/133
>ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
>ata1.00: configured for UDMA/133
>ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
>usb 2-1: new low speed USB device using uhci_hcd and address 2
>ata2.00: ATA-6: HDS722525VLSA80, V36OA63A, max UDMA/100
>ata2.00: 488397168 sectors, multi 16: LBA48 
>ata2.00: configured for UDMA/100
>scsi 0:0:0:0: Direct-Access     ATA      HDT722525DLA380  V44O PQ: 0 ANSI: 5
>sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
>sd 0:0:0:0: [sda] Write Protect is off
>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
>sd 0:0:0:0: [sda] Write Protect is off
>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: sda1
>sd 0:0:0:0: [sda] Attached SCSI disk
>scsi 1:0:0:0: Direct-Access     ATA      HDS722525VLSA80  V36O PQ: 0 ANSI: 5
>sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
>sd 1:0:0:0: [sdb] Write Protect is off
>sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
>sd 1:0:0:0: [sdb] Write Protect is off
>sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdb: sdb1 sdb2 sdb3 <<6>usb 2-1: configuration #1 chosen from 1 choice
> sdb5 > sdb4
>sd 1:0:0:0: [sdb] Attached SCSI disk
>input: Logitech USB Receiver as /class/input/input1
>input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:10.0-1
>usb 2-2: new low speed USB device using uhci_hcd and address 3
>usb 2-2: configuration #1 chosen from 1 choice
>input: Chicony USB Gaming Keyboard Pro as /class/input/input2
>input: USB HID v1.11 Keyboard [Chicony USB Gaming Keyboard Pro] on usb-0000:00:10.0-2
>input: Chicony USB Gaming Keyboard Pro as /class/input/input3
>input,hiddev96: USB HID v1.11 Device [Chicony USB Gaming Keyboard Pro] on usb-0000:00:10.0-2
>input: Chicony USB Gaming Keyboard Pro as /class/input/input4
>input: USB HID v1.11 Gamepad [Chicony USB Gaming Keyboard Pro] on usb-0000:00:10.0-2
>sata_sil 0000:00:0b.0: version 2.3
>ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 18
>sata_sil 0000:00:0b.0: cache line size not set.  Driver may not function
>scsi2 : sata_sil
>scsi3 : sata_sil
>ata3: SATA max UDMA/100 cmd 0xf8840080 ctl 0xf884008a bmdma 0xf8840000 irq 18
>ata4: SATA max UDMA/100 cmd 0xf88400c0 ctl 0xf88400ca bmdma 0xf8840008 irq 18
>ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>ata3.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133
>ata3.00: 488397168 sectors, multi 16: LBA48 
>ata3.00: configured for UDMA/100
>ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>ata4.00: ATA-6: HDS722525VLSA80, V36OA63A, max UDMA/100
>ata4.00: 488397168 sectors, multi 16: LBA48 
>ata4.00: configured for UDMA/100
>scsi 2:0:0:0: Direct-Access     ATA      WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
>sd 2:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB)
>sd 2:0:0:0: [sdc] Write Protect is off
>sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
>sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 2:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB)
>sd 2:0:0:0: [sdc] Write Protect is off
>sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
>sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdc: sdc1
>sd 2:0:0:0: [sdc] Attached SCSI disk
>scsi 3:0:0:0: Direct-Access     ATA      HDS722525VLSA80  V36O PQ: 0 ANSI: 5
>sd 3:0:0:0: [sdd] 488397168 512-byte hardware sectors (250059 MB)
>sd 3:0:0:0: [sdd] Write Protect is off
>sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
>sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 3:0:0:0: [sdd] 488397168 512-byte hardware sectors (250059 MB)
>sd 3:0:0:0: [sdd] Write Protect is off
>sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
>sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdd: sdd1
>sd 3:0:0:0: [sdd] Attached SCSI disk
>pata_via 0000:00:0f.1: version 0.3.2
>ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 17
>scsi4 : pata_via
>scsi5 : pata_via
>ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001e800 irq 14
>ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001e808 irq 15
>ata5.00: ATAPI: ASUS    DRW-1814BL, 1.10, max UDMA/66
>ata5.01: ATA-5: WDC WD600BB-00CAA1, 17.07W17, max UDMA/100
>ata5.01: 117231408 sectors, multi 16: LBA 
>ata5.00: configured for UDMA/66
>ata5.01: configured for UDMA/100
>ata6: port disabled. ignoring.
>scsi 4:0:0:0: CD-ROM            ASUS     DRW-1814BL       1.10 PQ: 0 ANSI: 5
>scsi 4:0:1:0: Direct-Access     ATA      WDC WD600BB-00CA 17.0 PQ: 0 ANSI: 5
>sd 4:0:1:0: [sde] 117231408 512-byte hardware sectors (60022 MB)
>sd 4:0:1:0: [sde] Write Protect is off
>sd 4:0:1:0: [sde] Mode Sense: 00 3a 00 00
>sd 4:0:1:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 4:0:1:0: [sde] 117231408 512-byte hardware sectors (60022 MB)
>sd 4:0:1:0: [sde] Write Protect is off
>sd 4:0:1:0: [sde] Mode Sense: 00 3a 00 00
>sd 4:0:1:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sde: sde1 sde2
>sd 4:0:1:0: [sde] Attached SCSI disk
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs: mounted filesystem with ordered data mode.
>SELinux:  Disabled at runtime.
>SELinux:  Unregistering netfilter hooks
>audit(1195833400.839:2): selinux=0 auid=4294967295
>FDC 0 is a post-1991 82077
>sd 0:0:0:0: Attached scsi generic sg0 type 0
>sd 1:0:0:0: Attached scsi generic sg1 type 0
>sd 2:0:0:0: Attached scsi generic sg2 type 0
>sd 3:0:0:0: Attached scsi generic sg3 type 0
>scsi 4:0:0:0: Attached scsi generic sg4 type 5
>sd 4:0:1:0: Attached scsi generic sg5 type 0
>sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
>Uniform CD-ROM driver Revision: 3.20
>sr 4:0:0:0: Attached scsi CD-ROM sr0
>input: PC Speaker as /class/input/input5
>parport_pc 00:0a: reported by Plug and Play ACPI
>parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
>Linux video capture interface: v2.00
>input: Power Button (FF) as /class/input/input6
>ACPI: Power Button (FF) [PWRF]
>input: Power Button (CM) as /class/input/input7
>ACPI: Power Button (CM) [PWRB]
>parport0: Printer, HEWLETT-PACKARD DESKJET 810C
>nvidia: module license 'NVIDIA' taints kernel.
>VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.14
>Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
>Copyright (c) 2004 Red Hat Inc.
>ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 22 (level, low) -> IRQ 19
>eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
>eth0: Ethernet Address: 00:50:8D:E9:38:46
>ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
>NVRM: loading NVIDIA UNIX x86 Kernel Module  100.14.19  Wed Sep 12 14:12:24 PDT 2007
>ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 21
>phy0: Selected rate control algorithm 'simple'
>bttv: driver version 0.9.17 loaded
>bttv: using 8 buffers with 2080k (520 pages) each for capture
>bttv: Bt8xx card found (0).
>ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 20 (level, low) -> IRQ 17
>bttv0: Bt878 (rev 2) at 0000:00:0c.0, irq: 17, latency: 32, mmio: 0xf3082000
>bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
>bttv0: using: Hauppauge (bt878) [card=10,autodetected]
>bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
>bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
>tveeprom 1-0050: Hauppauge model 61381, rev D123, serial# 1411033
>tveeprom 1-0050: tuner model is Philips FM1236 (idx 23, type 2)
>tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
>tveeprom 1-0050: audio processor is MSP3430 (idx 7)
>tveeprom 1-0050: has radio
>bttv0: Hauppauge eeprom indicates model#61381
>bttv0: tuner type=2
>bttv0: i2c: checking for MSP34xx @ 0x80... found
>msp3400 1-0040: MSP3430G-A1 found @ 0x80 (bt878 #0 [sw])
>msp3400 1-0040: MSP3430G-A1 supports radio, mode is autodetect and autoselect
>bttv0: i2c: checking for TDA9875 @ 0xb0... not found
>bttv0: i2c: checking for TDA7432 @ 0x8a... not found
>tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
>tuner 1-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
>tuner 1-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
>bttv0: registered device video0
>bttv0: registered device vbi0
>bttv0: registered device radio0
>bttv0: PLL: 28636363 => 35468950 .. ok
>ACPI: PCI Interrupt 0000:00:0c.1[A] -> GSI 20 (level, low) -> IRQ 17
>bt87x0: Using board 1, analog, digital (rate 32000 Hz)
>ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 19
>PCI: Setting latency timer of device 0000:00:11.5 to 64
>bt878: AUDIO driver version 0.0.0 loaded
>device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
>device-mapper: multipath: version 1.0.5 loaded
>EXT3 FS on sdb2, internal journal
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sdb1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
>EXT3 FS on sda1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
>EXT3 FS on sdb4, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
>EXT3 FS on sdd1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sdc1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>Adding 1052216k swap on /dev/sdb5.  Priority:-1 extents:1 across:1052216k
>Clocksource tsc unstable (delta = -64977116 ns)
>NET: Registered protocol family 10
>lo: Disabled Privacy Extensions
>Velocity is AUTO mode
>ADDRCONF(NETDEV_UP): eth0: link is not ready
>eth0: Link auto-negotiation speed 100M bps full duplex
>ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>audit(1195862214.017:3): audit_pid=2060 old=0 by auid=4294967295
>Bridge firewalling registered
>virbr0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
>ip_tables: (C) 2000-2006 Netfilter Core Team
>Netfilter messages via NETLINK v0.30.
>nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
>eth0: no IPv6 routers present
>agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
>agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
>agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
>virbr0: no IPv6 routers present
>ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
>ata5.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x1e data 0 
>         res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
>ata5: soft resetting port
>ata5.01: qc timeout (cmd 0xf8)
>ata5.01: ata_hpa_resize 1: hpa sectors (0) is smaller than sectors (117231408)
>ata5.00: failed to IDENTIFY (I/O error, err_mask=0x40)
>ata5.00: revalidation failed (errno=-5)
>ata5: failed to recover some devices, retrying in 5 secs
>ata5: soft resetting port
>ata5.01: qc timeout (cmd 0xf8)
>ata5.01: ata_hpa_resize 1: hpa sectors (0) is smaller than sectors (117231408)
>ata5.00: failed to IDENTIFY (I/O error, err_mask=0x40)
>ata5.00: revalidation failed (errno=-5)
>ata5.00: limiting speed to UDMA/66:PIO3
>ata5: failed to recover some devices, retrying in 5 secs
>ata5: soft resetting port
>ata5.01: qc timeout (cmd 0xf8)
>ata5.01: ata_hpa_resize 1: hpa sectors (0) is smaller than sectors (117231408)
>ata5.00: failed to IDENTIFY (I/O error, err_mask=0x40)
>ata5.00: revalidation failed (errno=-5)
>ata5.00: disabled
>ata5: failed to recover some devices, retrying in 5 secs
>ata5.01: failed to set xfermode (err_mask=0x40)
>ata5: failed to recover some devices, retrying in 5 secs
>ata5: soft resetting port
>ata5.01: qc timeout (cmd 0xf8)
>ata5.01: ata_hpa_resize 1: hpa sectors (0) is smaller than sectors (117231408)
>ata5.01: failed to set xfermode (err_mask=0x40)
>ata5.01: limiting speed to UDMA/100:PIO3
>ata5: failed to recover some devices, retrying in 5 secs
>ata5: soft resetting port
>ata5.01: qc timeout (cmd 0xf8)
>ata5.01: ata_hpa_resize 1: hpa sectors (0) is smaller than sectors (117231408)
>ata5.01: failed to set xfermode (err_mask=0x40)
>ata5.01: disabled
>ata5: EH pending after completion, repeating EH (cnt=4)
>ata5: soft resetting port
>ata5: EH complete
>sd 4:0:1:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sde, sector 295
>FAT: FAT read failed (blocknr 232)
>sd 4:0:1:0: [sde] READ CAPACITY failed
>sd 4:0:1:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>sd 4:0:1:0: [sde] Sense not available.
>sd 4:0:1:0: [sde] Write Protect is off
>sd 4:0:1:0: [sde] Mode Sense: 00 00 00 00
>sd 4:0:1:0: [sde] Asking for cache data failed
>sd 4:0:1:0: [sde] Assuming drive cache: write through
>FAT: Directory bread(block 111936) failed
>FAT: Directory bread(block 111937) failed
>FAT: Directory bread(block 111938) failed
>FAT: Directory bread(block 111939) failed
>FAT: Directory bread(block 111940) failed
>FAT: Directory bread(block 111941) failed
>FAT: Directory bread(block 111942) failed
>FAT: Directory bread(block 111943) failed
>FAT: Directory bread(block 111944) failed
>FAT: Directory bread(block 111945) failed
>FAT: Directory bread(block 111946) failed
>FAT: Directory bread(block 111947) failed
>FAT: Directory bread(block 111948) failed
>FAT: Directory bread(block 111949) failed
>FAT: Directory bread(block 111950) failed
>FAT: Directory bread(block 111951) failed
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 298)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 493)
>FAT: FAT read failed (blocknr 495)
>FAT: FAT read failed (blocknr 686)
>FAT: FAT read failed (blocknr 2656)
>FAT: Directory bread(block 113776) failed
>FAT: Directory bread(block 113777) failed
>FAT: Directory bread(block 113778) failed
>FAT: Directory bread(block 113779) failed
>FAT: Directory bread(block 113780) failed
>FAT: Directory bread(block 113781) failed
>FAT: Directory bread(block 113782) failed
>FAT: Directory bread(block 113783) failed
>FAT: Directory bread(block 113784) failed
>FAT: Directory bread(block 113785) failed
>FAT: Directory bread(block 113786) failed
>FAT: Directory bread(block 113787) failed
>FAT: Directory bread(block 113788) failed
>FAT: Directory bread(block 113789) failed
>FAT: Directory bread(block 113790) failed
>FAT: Directory bread(block 113791) failed
>FAT: FAT read failed (blocknr 2682)
>FAT: FAT read failed (blocknr 5745)
>FAT: FAT read failed (blocknr 5431)
>FAT: FAT read failed (blocknr 7873)
>FAT: FAT read failed (blocknr 6192)
>FAT: Directory bread(block 143904) failed
>FAT: Directory bread(block 143905) failed
>FAT: Directory bread(block 143906) failed
>FAT: Directory bread(block 143907) failed
>FAT: Directory bread(block 143908) failed
>FAT: Directory bread(block 143909) failed
>FAT: Directory bread(block 143910) failed
>FAT: Directory bread(block 143911) failed
>FAT: Directory bread(block 143912) failed
>FAT: Directory bread(block 143913) failed
>FAT: Directory bread(block 143914) failed
>FAT: Directory bread(block 143915) failed
>FAT: Directory bread(block 143916) failed
>FAT: Directory bread(block 143917) failed
>FAT: Directory bread(block 143918) failed
>FAT: Directory bread(block 143919) failed
>FAT: Directory bread(block 111936) failed
>FAT: Directory bread(block 111937) failed
>FAT: Directory bread(block 111938) failed
>FAT: Directory bread(block 111939) failed
>FAT: Directory bread(block 111940) failed
>FAT: Directory bread(block 111941) failed
>FAT: Directory bread(block 111942) failed
>FAT: Directory bread(block 111943) failed
>FAT: Directory bread(block 111944) failed
>FAT: Directory bread(block 111945) failed
>FAT: Directory bread(block 111946) failed
>FAT: Directory bread(block 111947) failed
>FAT: Directory bread(block 111948) failed
>FAT: Directory bread(block 111949) failed
>FAT: Directory bread(block 111950) failed
>FAT: Directory bread(block 111951) failed
>FAT: Directory bread(block 113776) failed
>FAT: Directory bread(block 113777) failed
>FAT: Directory bread(block 113778) failed
>FAT: Directory bread(block 113779) failed
>FAT: Directory bread(block 113780) failed
>FAT: Directory bread(block 113781) failed
>FAT: Directory bread(block 113782) failed
>FAT: Directory bread(block 113783) failed
>FAT: Directory bread(block 113784) failed
>FAT: Directory bread(block 113785) failed
>FAT: Directory bread(block 113786) failed
>FAT: Directory bread(block 113787) failed
>FAT: Directory bread(block 113788) failed
>FAT: Directory bread(block 113789) failed
>FAT: Directory bread(block 113790) failed
>FAT: Directory bread(block 113791) failed
>FAT: Directory bread(block 143904) failed
>FAT: Directory bread(block 143905) failed
>FAT: Directory bread(block 143906) failed
>FAT: Directory bread(block 143907) failed
>FAT: Directory bread(block 143908) failed
>FAT: Directory bread(block 143909) failed
>FAT: Directory bread(block 143910) failed
>FAT: Directory bread(block 143911) failed
>FAT: Directory bread(block 143912) failed
>FAT: Directory bread(block 143913) failed
>FAT: Directory bread(block 143914) failed
>FAT: Directory bread(block 143915) failed
>FAT: Directory bread(block 143916) failed
>FAT: Directory bread(block 143917) failed
>FAT: Directory bread(block 143918) failed
>FAT: Directory bread(block 143919) failed
>FAT: FAT read failed (blocknr 232)
>FAT: FAT read failed (blocknr 232)
>FAT: Directory bread(block 111936) failed
>FAT: Directory bread(block 111937) failed
>FAT: Directory bread(block 111938) failed
>FAT: Directory bread(block 111939) failed
>FAT: Directory bread(block 111940) failed
>FAT: Directory bread(block 111941) failed
>FAT: Directory bread(block 111942) failed
>FAT: Directory bread(block 111943) failed
>FAT: Directory bread(block 111944) failed
>FAT: Directory bread(block 111945) failed
>FAT: Directory bread(block 111946) failed
>FAT: Directory bread(block 111947) failed
>FAT: Directory bread(block 111948) failed
>FAT: Directory bread(block 111949) failed
>FAT: Directory bread(block 111950) failed
>FAT: Directory bread(block 111951) failed
>FAT: Directory bread(block 111936) failed
>FAT: Directory bread(block 111937) failed
>FAT: Directory bread(block 111938) failed
>FAT: Directory bread(block 111939) failed
>FAT: Directory bread(block 111940) failed
>FAT: Directory bread(block 111941) failed
>FAT: Directory bread(block 111942) failed
>FAT: Directory bread(block 111943) failed
>FAT: Directory bread(block 111944) failed
>FAT: Directory bread(block 111945) failed
>FAT: Directory bread(block 111946) failed
>FAT: Directory bread(block 111947) failed
>FAT: Directory bread(block 111948) failed
>FAT: Directory bread(block 111949) failed
>FAT: Directory bread(block 111950) failed
>FAT: Directory bread(block 111951) failed
>FAT: FAT read failed (blocknr 232)
>FAT: FAT read failed (blocknr 232)
>FAT: Directory bread(block 113776) failed
>FAT: Directory bread(block 113777) failed
>FAT: Directory bread(block 113778) failed
>FAT: Directory bread(block 113779) failed
>FAT: Directory bread(block 113780) failed
>FAT: Directory bread(block 113781) failed
>FAT: Directory bread(block 113782) failed
>FAT: Directory bread(block 113783) failed
>FAT: Directory bread(block 113784) failed
>FAT: Directory bread(block 113785) failed
>FAT: Directory bread(block 113786) failed
>FAT: Directory bread(block 113787) failed
>FAT: Directory bread(block 113788) failed
>FAT: Directory bread(block 113789) failed
>FAT: Directory bread(block 113790) failed
>FAT: Directory bread(block 113791) failed
>FAT: Directory bread(block 113776) failed
>FAT: Directory bread(block 113777) failed
>FAT: Directory bread(block 113778) failed
>FAT: Directory bread(block 113779) failed
>FAT: Directory bread(block 113780) failed
>FAT: Directory bread(block 113781) failed
>FAT: Directory bread(block 113782) failed
>FAT: Directory bread(block 113783) failed
>FAT: Directory bread(block 113784) failed
>FAT: Directory bread(block 113785) failed
>FAT: Directory bread(block 113786) failed
>FAT: Directory bread(block 113787) failed
>FAT: Directory bread(block 113788) failed
>FAT: Directory bread(block 113789) failed
>FAT: Directory bread(block 113790) failed
>FAT: Directory bread(block 113791) failed
>FAT: FAT read failed (blocknr 232)
>FAT: FAT read failed (blocknr 232)
>FAT: Directory bread(block 143904) failed
>FAT: Directory bread(block 143905) failed
>FAT: Directory bread(block 143906) failed
>FAT: Directory bread(block 143907) failed
>FAT: Directory bread(block 143908) failed
>FAT: Directory bread(block 143909) failed
>FAT: Directory bread(block 143910) failed
>FAT: Directory bread(block 143911) failed
>FAT: Directory bread(block 143912) failed
>FAT: Directory bread(block 143913) failed
>FAT: Directory bread(block 143914) failed
>FAT: Directory bread(block 143915) failed
>FAT: Directory bread(block 143916) failed
>FAT: Directory bread(block 143917) failed
>FAT: Directory bread(block 143918) failed
>FAT: Directory bread(block 143919) failed
>FAT: Directory bread(block 143904) failed
>FAT: Directory bread(block 143905) failed
>FAT: Directory bread(block 143906) failed
>FAT: Directory bread(block 143907) failed
>FAT: Directory bread(block 143908) failed
>FAT: Directory bread(block 143909) failed
>FAT: Directory bread(block 143910) failed
>FAT: Directory bread(block 143911) failed
>FAT: Directory bread(block 143912) failed
>FAT: Directory bread(block 143913) failed
>FAT: Directory bread(block 143914) failed
>FAT: Directory bread(block 143915) failed
>FAT: Directory bread(block 143916) failed
>FAT: Directory bread(block 143917) failed
>FAT: Directory bread(block 143918) failed
>FAT: Directory bread(block 143919) failed
>FAT: FAT read failed (blocknr 232)
>FAT: FAT read failed (blocknr 232)
>Buffer I/O error on device sde1, logical block 30000
>lost page write due to I/O error on sde1
>
>lspci -vvv output: 
>
>00:00.0 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
>	Latency: 8
>	Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
>	Capabilities: [80] AGP version 3.0
>		Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
>		Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
>	Capabilities: [50] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>	Capabilities: [60] HyperTransport: Slave or Primary Interface
>		!!! Possibly incomplete decoding
>		Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir-
>		Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
>		Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
>		Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
>		Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
>		Revision ID: 1.02
>	Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration
>
>00:00.1 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>
>00:00.2 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>
>00:00.3 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>
>00:00.4 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>
>00:00.7 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>
>00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] (prog-if 00 [Normal decode])
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
>	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>	I/O behind bridge: 0000f000-00000fff
>	Memory behind bridge: f0000000-f2ffffff
>	Prefetchable memory behind bridge: e0000000-efffffff
>	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
>	BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
>	Capabilities: [80] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:09.0 Network controller: RaLink RT2500 802.11g Cardbus/mini-PCI (rev 01)
>	Subsystem: Linksys WMP54G 2.0 PCI Adapter
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32, Cache Line Size: 64 bytes
>	Interrupt: pin A routed to IRQ 21
>	Region 0: Memory at f3080000 (32-bit, non-prefetchable) [size=8K]
>	Capabilities: [40] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02)
>	Subsystem: Silicon Image, Inc. SiI 3112 SATARaid Controller
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32
>	Interrupt: pin A routed to IRQ 18
>	Region 0: I/O ports at e100 [size=8]
>	Region 1: I/O ports at e700 [size=4]
>	Region 2: I/O ports at ed00 [size=8]
>	Region 3: I/O ports at ee00 [size=4]
>	Region 4: I/O ports at e000 [size=16]
>	Region 5: Memory at f3086000 (32-bit, non-prefetchable) [size=512]
>	[virtual] Expansion ROM at 40000000 [disabled] [size=512K]
>	Capabilities: [60] Power Management version 2
>		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
>00:0c.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 02)
>	Subsystem: Hauppauge computer works Inc. WinTV Series
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32 (4000ns min, 10000ns max)
>	Interrupt: pin A routed to IRQ 17
>	Region 0: Memory at f3082000 (32-bit, prefetchable) [size=4K]
>
>00:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 02)
>	Subsystem: Hauppauge computer works Inc. WinTV Series
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32 (1000ns min, 63750ns max)
>	Interrupt: pin A routed to IRQ 17
>	Region 0: Memory at f3083000 (32-bit, prefetchable) [size=4K]
>
>00:0e.0 Ethernet controller: VIA Technologies, Inc. VT6120/VT6121/VT6122 Gigabit Ethernet Adapter (rev 11)
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32 (750ns min, 2000ns max)
>	Interrupt: pin A routed to IRQ 19
>	Region 0: I/O ports at d000 [size=256]
>	Region 1: Memory at f3084000 (32-bit, non-prefetchable) [size=256]
>	[virtual] Expansion ROM at 40080000 [disabled] [size=128K]
>	Capabilities: [50] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32
>	Interrupt: pin B routed to IRQ 17
>	Region 0: I/O ports at e200 [size=8]
>	Region 1: I/O ports at e300 [size=4]
>	Region 2: I/O ports at e400 [size=8]
>	Region 3: I/O ports at e500 [size=4]
>	Region 4: I/O ports at e600 [size=16]
>	Region 5: I/O ports at d400 [size=256]
>	Capabilities: [c0] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32
>	Interrupt: pin A routed to IRQ 17
>	Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
>	Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
>	Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
>	Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
>	Region 4: I/O ports at e800 [size=16]
>	Capabilities: [c0] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32
>	Interrupt: pin A routed to IRQ 16
>	Region 4: I/O ports at e900 [size=32]
>	Capabilities: [80] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32
>	Interrupt: pin A routed to IRQ 16
>	Region 4: I/O ports at ea00 [size=32]
>	Capabilities: [80] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32
>	Interrupt: pin B routed to IRQ 16
>	Region 4: I/O ports at eb00 [size=32]
>	Capabilities: [80] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32
>	Interrupt: pin B routed to IRQ 16
>	Region 4: I/O ports at ec00 [size=32]
>	Capabilities: [80] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI])
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32, Cache Line Size: 64 bytes
>	Interrupt: pin C routed to IRQ 16
>	Region 0: Memory at f3085000 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [80] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Capabilities: [c0] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
>	Subsystem: ABIT Computer Corp. Unknown device 1415
>	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Interrupt: pin C routed to IRQ 19
>	Region 0: I/O ports at d800 [size=256]
>	Capabilities: [c0] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
>	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Capabilities: [80] HyperTransport: Host or Secondary Interface
>		!!! Possibly incomplete decoding
>		Command: WarmRst+ DblEnd-
>		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
>		Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
>		Revision ID: 1.02
>
>00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
>	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>
>00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
>	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>
>00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
>	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>
>01:00.0 VGA compatible controller: nVidia Corporation NV40 [GeForce 6800 GT] (rev a1) (prog-if 00 [VGA])
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 248 (1250ns min, 250ns max)
>	Interrupt: pin A routed to IRQ 20
>	Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=16M]
>	Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
>	Region 2: Memory at f1000000 (32-bit, non-prefetchable) [size=16M]
>	[virtual] Expansion ROM at f2000000 [disabled] [size=128K]
>	Capabilities: [60] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>	Capabilities: [44] AGP version 3.0
>		Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
>		Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
>

Actions: View

Attachments on bug 397521: 267841 | 274401