Attachment 297386 Details for Bug 436681 – Output of lspci

Output of lspci

lspci.txt (text/plain), 14.26 KB, created by Harsha Srinath on 2008-03-10 01:15:31 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Harsha Srinath

Created: 2008-03-10 01:15:31 UTC

Size: 14.26 KB

patch

obsolete

>00:00.0 Host bridge: Intel Corporation 82G33/G31/P35 Express DRAM Controller (rev 02)
>	Subsystem: Dell Unknown device 020d
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
>	Latency: 0
>	Capabilities: [e0] Vendor Specific Information
>
>00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35 Express PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0, Cache Line Size: 64 bytes
>	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>	I/O behind bridge: 0000c000-0000cfff
>	Memory behind bridge: fa000000-fcffffff
>	Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
>	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
>	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>	Capabilities: [88] Subsystem: Dell Unknown device 020d
>	Capabilities: [80] Power Management version 3
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>	Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
>		Address: fee0300c  Data: 41b1
>	Capabilities: [a0] Express Root Port (Slot+) IRQ 0
>		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
>		Device: Latency L0s <64ns, L1 <1us
>		Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
>		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
>		Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
>		Link: Latency L0s <256ns, L1 <4us
>		Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
>		Link: Speed 2.5Gb/s, Width x16
>		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
>		Slot: Number 0, PowerLimit 0.000000
>		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
>		Slot: AttnInd Off, PwrInd On, Power-
>		Root: Correctable- Non-Fatal- Fatal- PME-
>
>00:19.0 Ethernet controller: Intel Corporation 82562V-2 10/100 Network Connection (rev 02)
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin A routed to IRQ 222
>	Region 0: Memory at fdfc0000 (32-bit, non-prefetchable) [size=128K]
>	Region 1: Memory at fdfff000 (32-bit, non-prefetchable) [size=4K]
>	Region 2: I/O ports at ff00 [size=32]
>	Capabilities: [c8] Power Management version 2
>		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
>	Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
>		Address: 00000000fee0200c  Data: 41e9
>	Capabilities: [e0] Vendor Specific Information
>
>00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin A routed to IRQ 16
>	Region 4: I/O ports at fe00 [size=32]
>	Capabilities: [50] Vendor Specific Information
>
>00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) (prog-if 00 [UHCI])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin B routed to IRQ 19
>	Region 4: I/O ports at fd00 [size=32]
>	Capabilities: [50] Vendor Specific Information
>
>00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) (prog-if 00 [UHCI])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin D routed to IRQ 20
>	Region 4: I/O ports at fc00 [size=32]
>	Capabilities: [50] Vendor Specific Information
>
>00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) (prog-if 20 [EHCI])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin C routed to IRQ 17
>	Region 0: Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
>	Capabilities: [50] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02)
>	Subsystem: Dell Unknown device 020d
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0, Cache Line Size: 64 bytes
>	Interrupt: pin A routed to IRQ 22
>	Region 0: Memory at fdff4000 (64-bit, non-prefetchable) [size=16K]
>	Capabilities: [50] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>	Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
>		Address: 0000000000000000  Data: 0000
>	Capabilities: [70] Express Unknown type IRQ 0
>		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
>		Device: Latency L0s <64ns, L1 <1us
>		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
>		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
>		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
>		Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
>		Link: Latency L0s <64ns, L1 <1us
>		Link: ASPM Disabled CommClk- ExtSynch-
>		Link: Speed unknown, Width x0
>
>00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin A routed to IRQ 18
>	Region 4: I/O ports at fb00 [size=32]
>	Capabilities: [50] Vendor Specific Information
>
>00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin B routed to IRQ 20
>	Region 4: I/O ports at fa00 [size=32]
>	Capabilities: [50] Vendor Specific Information
>
>00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin C routed to IRQ 17
>	Region 4: I/O ports at f900 [size=32]
>	Capabilities: [50] Vendor Specific Information
>
>00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) (prog-if 20 [EHCI])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin A routed to IRQ 18
>	Region 0: Memory at fdffd000 (32-bit, non-prefetchable) [size=1K]
>	Capabilities: [50] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME+
>
>00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01 [Subtractive decode])
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
>	I/O behind bridge: 0000d000-0000dfff
>	Memory behind bridge: fde00000-fdefffff
>	Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff
>	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
>	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>	Capabilities: [50] Subsystem: Dell Unknown device 020d
>
>00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02)
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Capabilities: [e0] Vendor Specific Information
>
>00:1f.2 IDE interface: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 4 port SATA IDE Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin A routed to IRQ 20
>	Region 0: I/O ports at f800 [size=8]
>	Region 1: I/O ports at f700 [size=4]
>	Region 2: I/O ports at f600 [size=8]
>	Region 3: I/O ports at f500 [size=4]
>	Region 4: I/O ports at f400 [size=16]
>	Region 5: I/O ports at f300 [size=16]
>	Capabilities: [70] Power Management version 3
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>	Capabilities: [b0] Vendor Specific Information
>
>00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Interrupt: pin B routed to IRQ 17
>	Region 0: Memory at fdffc000 (64-bit, non-prefetchable) [size=256]
>	Region 4: I/O ports at 0500 [size=32]
>
>00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller (rev 02) (prog-if 85 [Master SecO PriO])
>	Subsystem: Dell Unknown device 020d
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0
>	Interrupt: pin A routed to IRQ 20
>	Region 0: I/O ports at f100 [size=8]
>	Region 1: I/O ports at f000 [size=4]
>	Region 2: I/O ports at ef00 [size=8]
>	Region 3: I/O ports at ee00 [size=4]
>	Region 4: I/O ports at ed00 [size=16]
>	Region 5: I/O ports at ec00 [size=16]
>	Capabilities: [70] Power Management version 3
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>	Capabilities: [b0] Vendor Specific Information
>
>01:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 LE] (rev a1) (prog-if 00 [VGA])
>	Subsystem: Dell Unknown device 0405
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 0, Cache Line Size: 64 bytes
>	Interrupt: pin A routed to IRQ 16
>	Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
>	Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
>	Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M]
>	[virtual] Expansion ROM at fc000000 [disabled] [size=128K]
>	Capabilities: [60] Power Management version 2
>		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>	Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
>		Address: 0000000000000000  Data: 0000
>	Capabilities: [78] Express Endpoint IRQ 0
>		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
>		Device: Latency L0s <256ns, L1 <4us
>		Device: AtnBtn- AtnInd- PwrInd-
>		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
>		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>		Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
>		Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
>		Link: Latency L0s <256ns, L1 <4us
>		Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
>		Link: Speed 2.5Gb/s, Width x16
>
>02:00.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
>	Subsystem: D-Link System Inc DFE-530TX+ 10/100 Ethernet Adapter
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32 (8000ns min, 16000ns max)
>	Interrupt: pin A routed to IRQ 19
>	Region 0: I/O ports at de00 [size=256]
>	Region 1: Memory at fdeff000 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [50] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>02:01.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
>	Subsystem: D-Link System Inc DFE-530TX+ 10/100 Ethernet Adapter
>	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>	Latency: 32 (8000ns min, 16000ns max)
>	Interrupt: pin A routed to IRQ 16
>	Region 0: I/O ports at dc00 [size=256]
>	Region 1: Memory at fdefe000 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [50] Power Management version 2
>		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
>		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>

Actions: View

Attachments on bug 436681: 297349 | 297350 | 297384 | 297385 | 297386 | 297387 | 297388 | 297389 | 297391 | 297392 | 297393 | 297394 | 297395