Attachment 298602 Details for Bug 438266 – 2.6.24 dmesg

2.6.24 dmesg

dmesg.2.6.24.3-34.fc8 (text/plain), 38.72 KB, created by Bas Mevissen on 2008-03-19 22:05:00 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Bas Mevissen

Created: 2008-03-19 22:05:00 UTC

Size: 38.72 KB

patch

obsolete

>Initializing cgroup subsys cpuset
>Linux version 2.6.24.3-34.fc8 (mockbuild@xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Wed Mar 12 16:51:49 EDT 2008
>Command line: ro root=LABEL=/-sda3 rhgb quiet
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007ff80000 (usable)
> BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data)
> BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS)
> BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
>Entering add_active_range(0, 0, 159) 0 entries of 3200 used
>Entering add_active_range(0, 256, 524160) 1 entries of 3200 used
>end_pfn_map = 1048576
>DMI 2.4 present.
>ACPI: RSDP 000FAF20, 0024 (r2 ACPIAM)
>ACPI: XSDT 7FF80100, 0064 (r1 NEC              1000724 MSFT       97)
>ACPI: FACP 7FF80290, 00F4 (r3 A_M_I_ OEMFACP   1000724 MSFT       97)
>ACPI: DSDT 7FF80590, 9560 (r1  A0543 A0543000        0 INTL 20060113)
>ACPI: FACS 7FF8E000, 0040
>ACPI: APIC 7FF80390, 0080 (r1 A_M_I_ OEMAPIC   1000724 MSFT       97)
>ACPI: SLIC 7FF80410, 0176 (r1 NEC              1000724 MSFT       97)
>ACPI: OEMB 7FF8E040, 0066 (r1 A_M_I_ AMI_OEM   1000724 MSFT       97)
>ACPI: HPET 7FF89AF0, 0038 (r1 A_M_I_ OEMHPET   1000724 MSFT       97)
>ACPI: MCFG 7FF89B30, 003C (r1 A_M_I_ OEMMCFG   1000724 MSFT       97)
>ACPI: SSDT 7FF8E0B0, 01C6 (r1    AMI   CPU1PM        1 INTL 20060113)
>ACPI: SSDT 7FF8E280, 013A (r1    AMI   CPU2PM        1 INTL 20060113)
>No NUMA configuration found
>Faking a node at 0000000000000000-000000007ff80000
>Entering add_active_range(0, 0, 159) 0 entries of 3200 used
>Entering add_active_range(0, 256, 524160) 1 entries of 3200 used
>Bootmem setup node 0 0000000000000000-000000007ff80000
> [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
> [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
> [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
> [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
> [ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
> [ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
> [ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
> [ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002e00000 on node 0
> [ffffe20001000000-ffffe200011fffff] PMD ->ffff810003200000 on node 0
> [ffffe20001200000-ffffe200013fffff] PMD ->ffff810003600000 on node 0
> [ffffe20001400000-ffffe200015fffff] PMD ->ffff810003a00000 on node 0
> [ffffe20001600000-ffffe200017fffff] PMD ->ffff810003e00000 on node 0
> [ffffe20001800000-ffffe200019fffff] PMD ->ffff810004200000 on node 0
> [ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810004600000 on node 0
>Zone PFN ranges:
>  DMA             0 ->     4096
>  DMA32        4096 ->  1048576
>  Normal    1048576 ->  1048576
>Movable zone start PFN for each node
>early_node_map[2] active PFN ranges
>    0:        0 ->      159
>    0:      256 ->   524160
>On node 0 totalpages: 524063
>  DMA zone: 56 pages used for memmap
>  DMA zone: 1326 pages reserved
>  DMA zone: 2617 pages, LIFO batch:0
>  DMA32 zone: 7110 pages used for memmap
>  DMA32 zone: 512954 pages, LIFO batch:31
>  Normal zone: 0 pages used for memmap
>  Movable zone: 0 pages used for memmap
>ACPI: PM-Timer IO Port: 0x808
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
>Processor #0 (Bootup-CPU)
>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
>Processor #1
>ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
>ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>ACPI: IRQ0 used by override.
>ACPI: IRQ2 used by override.
>ACPI: IRQ9 used by override.
>Setting APIC routing to flat
>ACPI: HPET id: 0x8086a201 base: 0xfed00000
>Using ACPI (MADT) for SMP configuration information
>swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
>swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
>swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
>Allocating PCI resources starting at 88000000 (gap: 80000000:7fb00000)
>SMP: Allowing 4 CPUs, 2 hotplug CPUs
>PERCPU: Allocating 42248 bytes of per cpu data
>Built 1 zonelists in Node order, mobility grouping on.  Total pages: 515571
>Policy zone: DMA32
>Kernel command line: ro root=LABEL=/-sda3 rhgb quiet
>Initializing CPU#0
>PID hash table entries: 4096 (order: 12, 32768 bytes)
>hpet clockevent registered
>TSC calibrated against HPET
>time.c: Detected 2404.112 MHz processor.
>Console: colour VGA+ 80x25
>console [tty0] enabled
>Checking aperture...
>Calgary: detecting Calgary via BIOS EBDA area
>Calgary: Unable to locate Rio Grande table in EBDA - bailing!
>Memory: 2058564k/2096640k available (2491k kernel code, 37688k reserved, 1390k data, 332k init)
>SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=4, Nodes=1
>Calibrating delay using timer specific routine.. 4810.96 BogoMIPS (lpj=2405481)
>Security Framework initialized
>SELinux:  Initializing.
>SELinux:  Starting in permissive mode
>selinux_register_security:  Registering secondary module capability
>Capability LSM initialized as secondary
>Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
>Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
>Mount-cache hash table entries: 256
>Initializing cgroup subsys ns
>Initializing cgroup subsys cpuacct
>CPU: L1 I cache: 32K, L1 D cache: 32K
>CPU: L2 cache: 4096K
>CPU 0/0 -> Node 0
>using mwait in idle threads.
>CPU: Physical Processor ID: 0
>CPU: Processor Core ID: 0
>SMP alternatives: switching to UP code
>ACPI: Core revision 20070126
>Using local APIC timer interrupts.
>APIC timer calibration result 16695222
>Detected 16.695 MHz APIC timer.
>SMP alternatives: switching to SMP code
>Booting processor 1/2 APIC 0x1
>Initializing CPU#1
>Calibrating delay using timer specific routine.. 4776.49 BogoMIPS (lpj=2388248)
>CPU: L1 I cache: 32K, L1 D cache: 32K
>CPU: L2 cache: 4096K
>CPU 1/1 -> Node 0
>CPU: Physical Processor ID: 0
>CPU: Processor Core ID: 1
>Intel(R) Core(TM)2 CPU          6600  @ 2.40GHz stepping 06
>checking TSC synchronization [CPU#0 -> CPU#1]: passed.
>Brought up 2 CPUs
>sizeof(vma)=176 bytes
>sizeof(page)=56 bytes
>sizeof(inode)=560 bytes
>sizeof(dentry)=208 bytes
>sizeof(ext3inode)=760 bytes
>sizeof(buffer_head)=104 bytes
>sizeof(skbuff)=224 bytes
>sizeof(task_struct)=2224 bytes
>CPU0 attaching sched-domain:
> domain 0: span 00000000,00000003
>  groups: 00000000,00000001 00000000,00000002
>  domain 1: span 00000000,00000003
>   groups: 00000000,00000003
>CPU1 attaching sched-domain:
> domain 0: span 00000000,00000003
>  groups: 00000000,00000002 00000000,00000001
>  domain 1: span 00000000,00000003
>   groups: 00000000,00000003
>net_namespace: 120 bytes
>Time: 21:07:00  Date: 03/19/08
>NET: Registered protocol family 16
>No dock devices found.
>ACPI: bus type pci registered
>PCI: Using configuration type 1
>ACPI: EC: Look up EC in DSDT
>ACPI: Interpreter enabled
>ACPI: (supports S0 S1 S3 S4 S5)
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
>PCI quirk: region 0480-04bf claimed by ICH6 GPIO
>PCI: Transparent bridge - 0000:00:1e.0
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
>ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15)
>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
>ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] -  C4, should be BB [20070126]
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI init
>ACPI: bus type pnp registered
>pnp: PnP ACPI: found 14 devices
>ACPI: ACPI bus type pnp unregistered
>usbcore: registered new interface driver usbfs
>usbcore: registered new interface driver hub
>usbcore: registered new device driver usb
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
>NetLabel: Initializing
>NetLabel:  domain hash size = 128
>NetLabel:  protocols = UNLABELED CIPSOv4
>NetLabel:  unlabeled traffic allowed by default
>DMAR:No DMAR devices found
>PCI-GART: No AMD northbridge found.
>hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
>hpet0: 3 64-bit timers, 14318180 Hz
>Time: tsc clocksource has been installed.
>system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
>system 00:07: ioport range 0x290-0x297 has been reserved
>system 00:08: ioport range 0x4d0-0x4d1 has been reserved
>system 00:08: ioport range 0x800-0x87f has been reserved
>system 00:08: ioport range 0x400-0x41f has been reserved
>system 00:08: ioport range 0x480-0x4bf has been reserved
>system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
>system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
>system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
>system 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved
>system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved
>system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
>system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
>system 00:0c: iomem range 0xf0000000-0xf3ffffff has been reserved
>system 00:0d: iomem range 0x0-0x9ffff could not be reserved
>system 00:0d: iomem range 0xc0000-0xdffff has been reserved
>system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
>system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
>system 00:0d: iomem range 0x0-0x0 could not be reserved
>PCI: Bridge: 0000:00:01.0
>  IO window: disabled.
>  MEM window: faa00000-feafffff
>  PREFETCH window: cff00000-efefffff
>PCI: Bridge: 0000:00:1c.0
>  IO window: disabled.
>  MEM window: disabled.
>  PREFETCH window: cfe00000-cfefffff
>PCI: Bridge: 0000:00:1c.3
>  IO window: c000-cfff
>  MEM window: fa900000-fa9fffff
>  PREFETCH window: disabled.
>PCI: Bridge: 0000:00:1c.4
>  IO window: b000-bfff
>  MEM window: fa800000-fa8fffff
>  PREFETCH window: disabled.
>PCI: Bridge: 0000:00:1e.0
>  IO window: disabled.
>  MEM window: fa700000-fa7fffff
>  PREFETCH window: disabled.
>ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
>PCI: Setting latency timer of device 0000:00:01.0 to 64
>ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
>PCI: Setting latency timer of device 0000:00:1c.0 to 64
>ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
>PCI: Setting latency timer of device 0000:00:1c.3 to 64
>ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
>PCI: Setting latency timer of device 0000:00:1c.4 to 64
>PCI: Setting latency timer of device 0000:00:1e.0 to 64
>NET: Registered protocol family 2
>IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
>TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
>TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
>TCP: Hash tables configured (established 262144 bind 65536)
>TCP reno registered
>checking if image is initramfs... it is
>Freeing initrd memory: 3275k freed
>audit: initializing netlink socket (disabled)
>audit(1205960819.435:1): initialized
>Total HugeTLB memory allocated, 0
>VFS: Disk quotas dquot_6.5.1
>Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
>SELinux:  Registering netfilter hooks
>ksign: Installing public key data
>Loading keyring
>- Added public key 4376F1951734BEB6
>- User ID: Red Hat, Inc. (Kernel Module GPG key)
>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>Boot video device is 0000:05:00.0
>PCI: Setting latency timer of device 0000:00:01.0 to 64
>assign_interrupt_mode Found MSI capability
>Allocate Port Service[0000:00:01.0:pcie00]
>PCI: Setting latency timer of device 0000:00:1c.0 to 64
>assign_interrupt_mode Found MSI capability
>Allocate Port Service[0000:00:1c.0:pcie00]
>Allocate Port Service[0000:00:1c.0:pcie02]
>PCI: Setting latency timer of device 0000:00:1c.3 to 64
>assign_interrupt_mode Found MSI capability
>Allocate Port Service[0000:00:1c.3:pcie00]
>PCI: Setting latency timer of device 0000:00:1c.4 to 64
>assign_interrupt_mode Found MSI capability
>Allocate Port Service[0000:00:1c.4:pcie00]
>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._OSC] (Node ffff81007f806540), AE_ALREADY_EXISTS
>ACPI: Marking method _OSC as Serialized
>ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._PDC] (Node ffff81007f806520), AE_ALREADY_EXISTS
>ACPI: Marking method _PDC as Serialized
>ACPI: Processor [CPU1] (supports 8 throttling states)
>ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._OSC] (Node ffff81007f806660), AE_ALREADY_EXISTS
>ACPI: Marking method _OSC as Serialized
>ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._PDC] (Node ffff81007f806640), AE_ALREADY_EXISTS
>ACPI: Marking method _PDC as Serialized
>ACPI: Processor [CPU2] (supports 8 throttling states)
>ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
>ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
>Real Time Clock Driver v1.12ac
>hpet_resources: 0xfed00000 is busy
>Non-volatile memory driver v1.2
>Linux agpgart interface v0.102
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>Switched to high resolution mode on CPU 1
>Switched to high resolution mode on CPU 0
>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
>input: Macintosh mouse button emulation as /devices/virtual/input/input0
>PNP: No PS/2 controller found. Probing ports directly.
>serio: i8042 KBD port at 0x60,0x64 irq 1
>serio: i8042 AUX port at 0x60,0x64 irq 12
>mice: PS/2 mouse device common for all mice
>cpuidle: using governor ladder
>cpuidle: using governor menu
>usbcore: registered new interface driver hiddev
>usbcore: registered new interface driver usbhid
>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
>TCP cubic registered
>Initializing XFRM netlink socket
>NET: Registered protocol family 1
>NET: Registered protocol family 17
>registered taskstats version 1
>  Magic number: 0:701:146
>  hash matches device device:17
>Freeing unused kernel memory: 332k freed
>Write protecting the kernel read-only data: 1080k
>ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
>PCI: Setting latency timer of device 0000:00:1d.7 to 64
>ehci_hcd 0000:00:1d.7: EHCI Host Controller
>ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
>ehci_hcd 0000:00:1d.7: debug port 1
>PCI: cache line size of 32 is not supported by device 0000:00:1d.7
>ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfebfbc00
>ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>usb usb1: configuration #1 chosen from 1 choice
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 8 ports detected
>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
>USB Universal Host Controller Interface driver v3.0
>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
>PCI: Setting latency timer of device 0000:00:1d.0 to 64
>uhci_hcd 0000:00:1d.0: UHCI Host Controller
>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
>uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000e480
>usb usb2: configuration #1 chosen from 1 choice
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
>PCI: Setting latency timer of device 0000:00:1d.1 to 64
>uhci_hcd 0000:00:1d.1: UHCI Host Controller
>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
>uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800
>usb usb3: configuration #1 chosen from 1 choice
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
>PCI: Setting latency timer of device 0000:00:1d.2 to 64
>uhci_hcd 0000:00:1d.2: UHCI Host Controller
>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
>uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e880
>usb usb4: configuration #1 chosen from 1 choice
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
>PCI: Setting latency timer of device 0000:00:1d.3 to 64
>uhci_hcd 0000:00:1d.3: UHCI Host Controller
>uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
>uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000ec00
>usb usb5: configuration #1 chosen from 1 choice
>hub 5-0:1.0: USB hub found
>hub 5-0:1.0: 2 ports detected
>SCSI subsystem initialized
>Driver 'sd' needs updating - please use bus_type methods
>libata version 3.00 loaded.
>ata_piix 0000:00:1f.1: version 2.12
>ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
>PCI: Setting latency timer of device 0000:00:1f.1 to 64
>scsi0 : ata_piix
>scsi1 : ata_piix
>ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
>ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
>usb 1-6: new high speed USB device using ehci_hcd and address 4
>usb 1-6: configuration #1 chosen from 1 choice
>usb 1-7: new high speed USB device using ehci_hcd and address 5
>ata1.00: ATAPI: HL-DT-STDVD-ROM GDR8164B, 0L06, max UDMA/33
>ata1.01: ATAPI: Optiarc DVD RW AD-7173A, 1-01, max UDMA/66
>usb 1-7: configuration #1 chosen from 1 choice
>hub 1-7:1.0: USB hub found
>hub 1-7:1.0: 4 ports detected
>ata1.00: configured for UDMA/33
>ata1.01: configured for UDMA/66
>usb 2-1: new full speed USB device using uhci_hcd and address 2
>scsi 0:0:0:0: CD-ROM            HL-DT-ST DVD-ROM GDR8164B 0L06 PQ: 0 ANSI: 5
>scsi 0:0:1:0: CD-ROM            Optiarc  DVD RW AD-7173A  1-01 PQ: 0 ANSI: 5
>ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
>usb 2-1: configuration #1 chosen from 1 choice
>ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23
>PCI: Setting latency timer of device 0000:00:1f.2 to 64
>scsi2 : ata_piix
>scsi3 : ata_piix
>ata3: SATA max UDMA/133 cmd 0xe400 ctl 0xe080 bmdma 0xd880 irq 23
>ata4: SATA max UDMA/133 cmd 0xe000 ctl 0xdc00 bmdma 0xd888 irq 23
>ata3.00: ATA-7: WDC WD3200KS-00PFB0, 21.00M21, max UDMA/133
>ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/1)
>usb 2-2: new low speed USB device using uhci_hcd and address 3
>ata3.00: configured for UDMA/133
>usb 2-2: configuration #1 chosen from 1 choice
>input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input1
>input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.0-2
>Fixing up Logitech keyboard report descriptor
>input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input2
>input,hiddev96,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-2
>usb 1-7.3: new high speed USB device using ehci_hcd and address 6
>ata4.00: ATA-6: Config  Disk, RGL10364, max UDMA/133
>ata4.00: 640 sectors, multi 1: LBA 
>ata4.00: Drive reports diagnostics failure. This may indicate a drive
>ata4.00: fault or invalid emulation. Contact drive vendor for information.
>ata4.00: device is on DMA blacklist, disabling DMA
>ata4.00: configured for PIO4
>scsi 2:0:0:0: Direct-Access     ATA      WDC WD3200KS-00P 21.0 PQ: 0 ANSI: 5
>sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
>sd 2:0:0:0: [sda] Write Protect is off
>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
>sd 2:0:0:0: [sda] Write Protect is off
>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: sda1 sda2 sda3 sda4 < sda5<6>usb 1-7.3: configuration #1 chosen from 1 choice
> sda6 >
>sd 2:0:0:0: [sda] Attached SCSI disk
>scsi 3:0:0:0: Direct-Access     ATA      Config  Disk     RGL1 PQ: 0 ANSI: 5
>sd 3:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
>sd 3:0:0:0: [sdb] Write Protect is off
>sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
>sd 3:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
>sd 3:0:0:0: [sdb] Write Protect is off
>sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
> sdb:<3>ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
>ata4.00: cmd c4/00:08:00:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
>         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
>ata4.00: status: { DRDY }
>ata4: soft resetting link
>ata4.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)
>ata4.00: revalidation failed (errno=-5)
>ata4: failed to recover some devices, retrying in 5 secs
>ata4: soft resetting link
>ata4: port is slow to respond, please be patient (Status 0xd0)
>ata4: SRST failed (errno=-16)
>ata4: soft resetting link
>ata4: port is slow to respond, please be patient (Status 0xd0)
>ata4: SRST failed (errno=-16)
>ata4: soft resetting link
>ata4: port is slow to respond, please be patient (Status 0xd0)
>ata4: SRST failed (errno=-16)
>ata4: soft resetting link
>ata4: SRST failed (errno=-16)
>ata4: reset failed, giving up
>ata4.00: disabled
>ata4: EH complete
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>Dev sdb: unable to read RDB block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
> unable to read partition table
>sd 3:0:0:0: [sdb] Attached SCSI disk
>Initializing USB Mass Storage driver...
>scsi4 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 4
>usb-storage: waiting for device to settle before scanning
>usbcore: registered new interface driver usb-storage
>USB Mass Storage support registered.
>usb-storage: device scan complete
>scsi 4:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
>scsi 4:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
>scsi 4:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
>scsi 4:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
>sd 4:0:0:0: [sdc] Attached SCSI removable disk
>sd 4:0:0:1: [sdd] Attached SCSI removable disk
>sd 4:0:0:2: [sde] Attached SCSI removable disk
>sd 4:0:0:3: [sdf] Attached SCSI removable disk
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 512
>Buffer I/O error on device sdb, logical block 64
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 512
>Buffer I/O error on device sdb, logical block 64
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>Buffer I/O error on device sdb, logical block 0
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 8
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 16
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 24
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 32
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 40
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 48
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 56
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 64
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 72
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 80
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 88
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 96
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 104
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 112
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 120
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs: mounted filesystem with ordered data mode.
>SELinux:8192 avtab hash slots allocated.Num of rules:217677
>SELinux:8192 avtab hash slots allocated.Num of rules:217677
>security:  8 users, 12 roles, 2372 types, 114 bools, 1 sens, 1024 cats
>security:  67 classes, 217677 rules
>SELinux:  Completing initialization.
>SELinux:  Setting up existing superblocks.
>SELinux: initialized (dev sda3, type ext3), uses xattr
>SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
>SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
>SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
>SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
>SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
>SELinux: initialized (dev devpts, type devpts), uses transition SIDs
>SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
>SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
>SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
>SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
>SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
>SELinux: initialized (dev proc, type proc), uses genfs_contexts
>SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
>SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
>SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
>SELinux: policy loaded with handle_unknown=allow
>audit(1205960931.292:2): policy loaded auid=4294967295
>Driver 'sr' needs updating - please use bus_type methods
>sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
>Uniform CD-ROM driver Revision: 3.20
>sr 0:0:0:0: Attached scsi CD-ROM sr0
>sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
>sr 0:0:1:0: Attached scsi CD-ROM sr1
>Floppy drive(s): fd0 is 1.44M
>FDC 0 is a post-1991 82077
>sr 0:0:0:0: Attached scsi generic sg0 type 5
>sr 0:0:1:0: Attached scsi generic sg1 type 5
>sd 2:0:0:0: Attached scsi generic sg2 type 0
>sd 3:0:0:0: Attached scsi generic sg3 type 0
>sd 4:0:0:0: Attached scsi generic sg4 type 0
>sd 4:0:0:1: Attached scsi generic sg5 type 0
>sd 4:0:0:2: Attached scsi generic sg6 type 0
>sd 4:0:0:3: Attached scsi generic sg7 type 0
>intel_rng: FWH not detected
>input: PC Speaker as /devices/platform/pcspkr/input/input3
>usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x03F0 pid 0x2D11
>usbcore: registered new interface driver usblp
>ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 23
>EDAC MC: Ver: 2.1.0 Mar 12 2008
>input: Power Button (FF) as /devices/virtual/input/input4
>ACPI: Power Button (FF) [PWRF]
>input: Power Button (CM) as /devices/virtual/input/input5
>iTCO_vendor_support: vendor-support=0
>ACPI: Power Button (CM) [PWRB]
>EDAC i82975x: ECC disabled on both channels.
>iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
>iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
>iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
>ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 21
>firewire_ohci: Added fw-ohci device 0000:01:03.0, OHCI version 1.10
>ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 19
>PCI: Setting latency timer of device 0000:03:00.0 to 64
>sky2 0000:03:00.0: v1.20 addr 0xfa9fc000 irq 19 Yukon-EC (0xb6) rev 2
>sky2 eth0: addr 00:18:f3:98:87:88
>ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
>PCI: Setting latency timer of device 0000:02:00.0 to 64
>sky2 0000:02:00.0: v1.20 addr 0xfa8fc000 irq 16 Yukon-EC (0xb6) rev 2
>sky2 eth1: addr 00:18:f3:98:85:c6
>nvidia: module license 'NVIDIA' taints kernel.
>firewire_core: created device fw0: GUID 0011d80000eeec09, S400
>ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16
>PCI: Setting latency timer of device 0000:05:00.0 to 64
>NVRM: loading NVIDIA UNIX x86_64 Kernel Module  169.12  Thu Feb 14 17:51:09 PST 2008
>ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 19
>PCI: Setting latency timer of device 0000:00:1b.0 to 64
>ALSA sound/pci/hda/hda_intel.c:732: codec_mask = 0x1
>ALSA sound/pci/hda/hda_codec.c:2162: hda_codec: model '6stack-dig' is selected for config 1043:81d8 (Asus P5WD)
>phy0: Selected rate control algorithm 'pid'
>phy0: hwaddr 00:15:af:08:a4:dc, rtl8187 V1 + rtl8225z2
>usbcore: registered new interface driver rtl8187
>SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
>NET: Registered protocol family 10
>lo: Disabled Privacy Extensions
>device-mapper: uevent: version 1.0.3
>device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
>device-mapper: multipath: version 1.0.5 loaded
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>printk: 16 messages suppressed.
>Buffer I/O error on device sdb, logical block 79
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>Buffer I/O error on device sdb, logical block 79
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 376
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 376
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 8
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 8
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 624
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 624
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 576
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 576
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 384
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 384
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 384
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 384
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 624
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 624
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 240
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 240
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 632
>EXT3 FS on sda3, internal journal
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sda5, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>SELinux: initialized (dev sda5, type ext3), uses xattr
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sda6, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>SELinux: initialized (dev sda6, type ext3), uses xattr
>SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
>Adding 10241428k swap on /dev/sda2.  Priority:-1 extents:1 across:10241428k
>SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
>IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
>warning: process `kudzu' used the deprecated sysctl system call with 1.23.
>ip6_tables: (C) 2000-2006 Netfilter Core Team
>nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
>ip_tables: (C) 2000-2006 Netfilter Core Team
>sky2 eth0: enabling interface
>ADDRCONF(NETDEV_UP): eth0: link is not ready
>sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
>ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>RPC: Registered udp transport module.
>RPC: Registered tcp transport module.
>SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
>fuse init (API version 7.9)
>SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
>w83627ehf: Found W83627EHG chip at 0x290
>coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
>coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
>audit(1205960953.727:3): audit_pid=2226 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
>SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
>SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
>SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
>Bluetooth: Core ver 2.11
>NET: Registered protocol family 31
>Bluetooth: HCI device and connection manager initialized
>Bluetooth: HCI socket layer initialized
>Bluetooth: L2CAP ver 2.9
>Bluetooth: L2CAP socket layer initialized
>Bluetooth: RFCOMM socket layer initialized
>Bluetooth: RFCOMM TTY layer initialized
>Bluetooth: RFCOMM ver 1.8
>eth0: no IPv6 routers present
>Bridge firewalling registered
>virbr0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
>virbr0: starting userspace STP failed, starting kernel STP
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>printk: 30 messages suppressed.
>Buffer I/O error on device sdb, logical block 0
>Buffer I/O error on device sdb, logical block 1
>Buffer I/O error on device sdb, logical block 2
>Buffer I/O error on device sdb, logical block 3
>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
>end_request: I/O error, dev sdb, sector 0
>virbr0: no IPv6 routers present
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sda1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>SELinux: initialized (dev sda1, type ext3), uses xattr
>usb 1-6: reset high speed USB device using ehci_hcd and address 4
>usb 1-6: reset high speed USB device using ehci_hcd and address 4

Actions: View

Attachments on bug 438266: 298601 | 298602