Attachment 313003 Details for Bug 457250 – Output of the dmesg

Output of the dmesg

dmesg (text/plain), 35.40 KB, created by Fehér János on 2008-07-30 14:58:19 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Fehér János

Created: 2008-07-30 14:58:19 UTC

Size: 35.40 KB

patch

obsolete

>Initializing cgroup subsys cpuset
>Initializing cgroup subsys cpu
>Linux version 2.6.26-0.115.rc9.git2.fc10.i686 (mockbuild@x86-3) (gcc version 4.3.1 20080624 (Red Hat 4.3.1-3) (GCC) ) #1 SMP Mon Jul 7 22:35:42 EDT 2008
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000078000000 (usable)
> BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
>x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
>1024MB HIGHMEM available.
>896MB LOWMEM available.
>found SMP MP-table at [c00ff780] 000ff780
>Using x86 segment limits to approximate NX protection
>Entering add_active_range(0, 0, 491520) 0 entries of 256 used
>Zone PFN ranges:
>  DMA             0 ->     4096
>  Normal       4096 ->   229376
>  HighMem    229376 ->   491520
>Movable zone start PFN for each node
>early_node_map[1] active PFN ranges
>    0:        0 ->   491520
>On node 0 totalpages: 491520
>  DMA zone: 56 pages used for memmap
>  DMA zone: 0 pages reserved
>  DMA zone: 4040 pages, LIFO batch:0
>  Normal zone: 3080 pages used for memmap
>  Normal zone: 222200 pages, LIFO batch:31
>  HighMem zone: 3584 pages used for memmap
>  HighMem zone: 258560 pages, LIFO batch:31
>  Movable zone: 0 pages used for memmap
>DMI present.
>Using APIC driver default
>ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080321]
>ATI board detected. Disabling timer routing over 8254.
>Detected use of extended apic ids on hypertransport bus
>Intel MultiProcessor Specification v1.4
>    Virtual Wire compatibility mode.
>MPTABLE: OEM ID: ATI      Product ID: RS690        <6>MPTABLE: Product ID: RS690        <6>MPTABLE: APIC at: 0xFEE00000
>Processor #0 (Bootup-CPU)
>Processor #1
>I/O APIC #2 Version 33 at 0xFEC00000.
>Enabling APIC mode:  Flat.  Using 1 I/O APICs
>Processors: 2
>Allocating PCI resources starting at 80000000 (gap: 78000000:87780000)
>PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
>PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
>PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
>SMP: Allowing 2 CPUs, 0 hotplug CPUs
>PERCPU: Allocating 336168 bytes of per cpu data
>NR_CPUS: 32, nr_cpu_ids: 2
>Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 484800
>Kernel command line: ro root=LABEL=/1 rhgb quiet
>mapped APIC to ffffb000 (fee00000)
>mapped IOAPIC to ffffa000 (fec00000)
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Initializing CPU#0
>CPU 0 irqstacks, hard=c0870000 soft=c0850000
>PID hash table entries: 4096 (order: 12, 16384 bytes)
>Detected 2394.445 MHz processor.
>Console: colour VGA+ 80x25
>console [tty0] enabled
>Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
>... MAX_LOCKDEP_SUBCLASSES:    8
>... MAX_LOCK_DEPTH:          48
>... MAX_LOCKDEP_KEYS:        2048
>... CLASSHASH_SIZE:           1024
>... MAX_LOCKDEP_ENTRIES:     8192
>... MAX_LOCKDEP_CHAINS:      16384
>... CHAINHASH_SIZE:          8192
> memory used by lock dependency info: 1024 kB
> per task-struct memory footprint: 2688 bytes
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 1925836k/1966080k available (2483k kernel code, 39000k reserved, 1319k data, 584k init, 1048576k highmem)
>virtual kernel memory layout:
>    fixmap  : 0xffc53000 - 0xfffff000   (3760 kB)
>    pkmap   : 0xff400000 - 0xff800000   (4096 kB)
>    vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
>    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
>      .init : 0xc07bb000 - 0xc084d000   ( 584 kB)
>      .data : 0xc066ce0e - 0xc07b6b80   (1319 kB)
>      .text : 0xc0400000 - 0xc066ce0e   (2483 kB)
>Checking if this processor honours the WP bit even in supervisor mode...Ok.
>CPA: page pool initialized 32 of 32 pages preallocated
>SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
>Calibrating delay using timer specific routine.. 4905.07 BogoMIPS (lpj=2452536)
>Security Framework initialized
>SELinux:  Initializing.
>SELinux:  Starting in permissive mode
>selinux_register_security:  Registering secondary module capability
>Capability LSM initialized as secondary
>Mount-cache hash table entries: 512
>Initializing cgroup subsys ns
>Initializing cgroup subsys cpuacct
>Initializing cgroup subsys devices
>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>CPU: L2 Cache: 512K (64 bytes/line)
>CPU 0(2) -> Core 0
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>Checking 'hlt' instruction... OK.
>ACPI: Core revision 20080321
>ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080321]
>ACPI: Unable to load the System Description Tables
>ExtINT not setup in hardware but reported by MP table
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
>CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 03
>lockdep: fixing up alternatives.
>CPU 1 irqstacks, hard=c0871000 soft=c0851000
>Booting processor 1/1 ip 6000
>Initializing CPU#1
>Calibrating delay using timer specific routine.. 4787.78 BogoMIPS (lpj=2393891)
>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>CPU: L2 Cache: 512K (64 bytes/line)
>CPU 1(2) -> Core 1
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#1.
>x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
>CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 03
>Brought up 2 CPUs
>Total of 2 processors activated (9692.85 BogoMIPS).
>sizeof(vma)=84 bytes
>sizeof(page)=56 bytes
>sizeof(inode)=608 bytes
>sizeof(dentry)=160 bytes
>sizeof(ext3inode)=860 bytes
>sizeof(buffer_head)=56 bytes
>sizeof(skbuff)=180 bytes
>sizeof(task_struct)=6056 bytes
>CPU0 attaching sched-domain:
> domain 0: span 0-1
>  groups: 0 1
>CPU1 attaching sched-domain:
> domain 0: span 0-1
>  groups: 1 0
>khelper used greatest stack depth: 3028 bytes left
>net_namespace: 732 bytes
>Booting paravirtualized kernel on bare hardware
>Time: 21:43:39  Date: 07/29/08
>khelper used greatest stack depth: 2640 bytes left
>NET: Registered protocol family 16
>PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
>PCI: Using configuration type 1 for base access
>Setting up standard PCI resources
>ACPI: Interpreter disabled.
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI: disabled
>SCSI subsystem initialized
>libata version 3.00 loaded.
>usbcore: registered new interface driver usbfs
>usbcore: registered new interface driver hub
>usbcore: registered new device driver usb
>PCI: Probing PCI hardware
>PCI: Probing PCI hardware (bus 00)
>pci 0000:00:12.0: set SATA to AHCI mode
>PCI: Transparent bridge - 0000:00:14.4
>PCI: Using IRQ router default [1002/438d] at 0000:00:14.3
>PCI->APIC IRQ transform: 0000:00:12.0[A] -> IRQ 22
>PCI->APIC IRQ transform: 0000:00:13.0[A] -> IRQ 16
>PCI->APIC IRQ transform: 0000:00:13.1[B] -> IRQ 17
>PCI->APIC IRQ transform: 0000:00:13.2[C] -> IRQ 18
>PCI->APIC IRQ transform: 0000:00:13.3[B] -> IRQ 17
>PCI->APIC IRQ transform: 0000:00:13.4[C] -> IRQ 18
>PCI->APIC IRQ transform: 0000:00:13.5[D] -> IRQ 19
>PCI->APIC IRQ transform: 0000:00:14.1[A] -> IRQ 16
>PCI->APIC IRQ transform: 0000:00:14.2[A] -> IRQ 16
>PCI->APIC IRQ transform: 0000:01:05.0[A] -> IRQ 18
>PCI->APIC IRQ transform: 0000:01:05.2[B] -> IRQ 19
>PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 19
>PCI->APIC IRQ transform: 0000:03:00.0[A] -> IRQ 20
>PCI->APIC IRQ transform: 0000:03:02.0[A] -> IRQ 22
>NetLabel: Initializing
>NetLabel:  domain hash size = 128
>NetLabel:  protocols = UNLABELED CIPSOv4
>NetLabel:  unlabeled traffic allowed by default
>PCI: Bridge: 0000:00:01.0
>  IO window: c000-cfff
>  MEM window: 0xfe800000-0xfe9fffff
>  PREFETCH window: 0x00000000f0000000-0x00000000f7ffffff
>PCI: Bridge: 0000:00:07.0
>  IO window: d000-dfff
>  MEM window: 0xfea00000-0xfeafffff
>  PREFETCH window: disabled.
>PCI: Bridge: 0000:00:14.4
>  IO window: e000-efff
>  MEM window: 0xfeb00000-0xfebfffff
>  PREFETCH window: disabled.
>PCI: Setting latency timer of device 0000:00:07.0 to 64
>NET: Registered protocol family 2
>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
>TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>TCP reno registered
>NET: Registered protocol family 1
>checking if image is initramfs... it is
>debug: unmapping init memory f7d75000..f7ff0000
>apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
>apm: disabled - APM is not SMP safe.
>audit: initializing netlink socket (disabled)
>type=2000 audit(1217367818.497:1): initialized
>highmem bounce pool size: 64 pages
>Total HugeTLB memory allocated, 0
>VFS: Disk quotas dquot_6.5.1
>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>msgmni has been set to 1715
>SELinux:  Registering netfilter hooks
>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>pci 0000:01:05.0: Boot video device
>PCI: Setting latency timer of device 0000:00:07.0 to 64
>assign_interrupt_mode Found MSI capability
>Allocate Port Service[0000:00:07.0:pcie00]
>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>isapnp: Scanning for PnP cards...
>isapnp: No Plug & Play device found
>Non-volatile memory driver v1.2
>Linux agpgart interface v0.103
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>brd: module loaded
>input: Macintosh mouse button emulation as /devices/virtual/input/input0
>Driver 'sd' needs updating - please use bus_type methods
>PNP: No PS/2 controller found. Probing ports directly.
>serio: i8042 KBD port at 0x60,0x64 irq 1
>serio: i8042 AUX port at 0x60,0x64 irq 12
>mice: PS/2 mouse device common for all mice
>rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
>rtc0: alarms up to one day
>cpuidle: using governor ladder
>cpuidle: using governor menu
>usbcore: registered new interface driver hiddev
>usbcore: registered new interface driver usbhid
>usbhid: v2.6:USB HID core driver
>TCP cubic registered
>Initializing XFRM netlink socket
>NET: Registered protocol family 17
>Using IPI No-Shortcut mode
>registered taskstats version 1
>  Magic number: 0:100:754
>debug: unmapping init memory c07bb000..c084d000
>Write protecting the kernel text: 2484k
>Write protecting the kernel read-only data: 1080k
>ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
>ehci_hcd 0000:00:13.5: EHCI Host Controller
>drivers/usb/core/inode.c: creating file 'devices'
>drivers/usb/core/inode.c: creating file '001'
>ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
>ehci_hcd 0000:00:13.5: reset hcs_params 0x10520a dbg=1 cc=5 pcc=2 ordered !ppc ports=10
>ehci_hcd 0000:00:13.5: reset hcc_params a072 thresh 7 uframes 256/512/1024
>ehci_hcd 0000:00:13.5: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
>ehci_hcd 0000:00:13.5: debug port 1
>ehci_hcd 0000:00:13.5: MWI active
>ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe7ff000
>ehci_hcd 0000:00:13.5: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
>ehci_hcd 0000:00:13.5: init command 010009 (park)=0 ithresh=1 period=256 RUN
>ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>usb usb1: default language 0x0409
>usb usb1: uevent
>usb usb1: usb_probe_device
>usb usb1: configuration #1 chosen from 1 choice
>usb usb1: adding 1-0:1.0 (config #1, interface 0)
>usb 1-0:1.0: uevent
>hub 1-0:1.0: usb_probe_interface
>hub 1-0:1.0: usb_probe_interface - got id
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 10 ports detected
>hub 1-0:1.0: standalone hub
>hub 1-0:1.0: no power switching (usb 1.0)
>hub 1-0:1.0: individual port over-current protection
>hub 1-0:1.0: power on to power good time: 20ms
>hub 1-0:1.0: local power source is good
>hub 1-0:1.0: trying to enable port power on non-switchable hub
>drivers/usb/core/inode.c: creating file '001'
>usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>usb usb1: Product: EHCI Host Controller
>usb usb1: Manufacturer: Linux 2.6.26-0.115.rc9.git2.fc10.i686 ehci_hcd
>usb usb1: SerialNumber: 0000:00:13.5
>modprobe used greatest stack depth: 1852 bytes left
>hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0000
>ehci_hcd 0000:00:13.5: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
>hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
>ohci_hcd: block sizes: ed 64 td 64
>ohci_hcd 0000:00:13.0: OHCI Host Controller
>drivers/usb/core/inode.c: creating file '002'
>ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
>ohci_hcd 0000:00:13.0: created debug files
>ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe7fe000
>ohci_hcd 0000:00:13.0: OHCI controller state
>ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
>ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
>ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
>ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
>ohci_hcd 0000:00:13.0: intrenable 0x8000001a MIE UE RD WDH
>ohci_hcd 0000:00:13.0: hcca frame #0005
>ohci_hcd 0000:00:13.0: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
>ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
>ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
>ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
>ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00000100 PPS
>usb usb2: default language 0x0409
>usb usb2: uevent
>usb usb2: usb_probe_device
>usb usb2: configuration #1 chosen from 1 choice
>usb usb2: adding 2-0:1.0 (config #1, interface 0)
>usb 2-0:1.0: uevent
>hub 2-0:1.0: usb_probe_interface
>hub 2-0:1.0: usb_probe_interface - got id
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 2 ports detected
>hub 2-0:1.0: standalone hub
>hub 2-0:1.0: no power switching (usb 1.0)
>hub 2-0:1.0: no over-current protection
>hub 2-0:1.0: power on to power good time: 4ms
>hub 2-0:1.0: local power source is good
>hub 2-0:1.0: trying to enable port power on non-switchable hub
>hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
>ehci_hcd 0000:00:13.5: port 1 full speed --> companion
>ehci_hcd 0000:00:13.5: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
>hub 1-0:1.0: port 1 not reset yet, waiting 50ms
>drivers/usb/core/inode.c: creating file '001'
>usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
>usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>usb usb2: Product: OHCI Host Controller
>usb usb2: Manufacturer: Linux 2.6.26-0.115.rc9.git2.fc10.i686 ohci_hcd
>usb usb2: SerialNumber: 0000:00:13.0
>ohci_hcd 0000:00:13.1: OHCI Host Controller
>drivers/usb/core/inode.c: creating file '003'
>ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
>ohci_hcd 0000:00:13.1: created debug files
>ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe7fd000
>ehci_hcd 0000:00:13.5: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
>ehci_hcd 0000:00:13.5: GetStatus port 3 status 001403 POWER sig=k CSC CONNECT
>hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
>ohci_hcd 0000:00:13.1: OHCI controller state
>ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
>ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3
>ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
>ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
>ohci_hcd 0000:00:13.1: intrenable 0x8000001a MIE UE RD WDH
>ohci_hcd 0000:00:13.1: hcca frame #0005
>ohci_hcd 0000:00:13.1: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
>ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
>ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
>ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00000100 PPS
>ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
>usb usb3: default language 0x0409
>usb usb3: uevent
>usb usb3: usb_probe_device
>usb usb3: configuration #1 chosen from 1 choice
>usb usb3: adding 3-0:1.0 (config #1, interface 0)
>usb 3-0:1.0: uevent
>hub 3-0:1.0: usb_probe_interface
>hub 3-0:1.0: usb_probe_interface - got id
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 2 ports detected
>hub 3-0:1.0: standalone hub
>hub 3-0:1.0: no power switching (usb 1.0)
>hub 3-0:1.0: no over-current protection
>hub 3-0:1.0: power on to power good time: 4ms
>hub 3-0:1.0: local power source is good
>hub 3-0:1.0: trying to enable port power on non-switchable hub
>hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
>ehci_hcd 0000:00:13.5: port 3 low speed --> companion
>drivers/usb/core/inode.c: creating file '001'
>usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
>usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>usb usb3: Product: OHCI Host Controller
>usb usb3: Manufacturer: Linux 2.6.26-0.115.rc9.git2.fc10.i686 ohci_hcd
>usb usb3: SerialNumber: 0000:00:13.1
>ohci_hcd 0000:00:13.2: OHCI Host Controller
>drivers/usb/core/inode.c: creating file '004'
>ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
>ohci_hcd 0000:00:13.2: created debug files
>ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe7fc000
>ehci_hcd 0000:00:13.5: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
>ehci_hcd 0000:00:13.5: GetStatus port 4 status 001403 POWER sig=k CSC CONNECT
>hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
>ohci_hcd 0000:00:13.2: OHCI controller state
>ohci_hcd 0000:00:13.2: OHCI 1.0, NO legacy support registers
>ohci_hcd 0000:00:13.2: control 0x083 HCFS=operational CBSR=3
>ohci_hcd 0000:00:13.2: cmdstatus 0x00000 SOC=0
>ohci_hcd 0000:00:13.2: intrstatus 0x00000004 SF
>ohci_hcd 0000:00:13.2: intrenable 0x8000001a MIE UE RD WDH
>ohci_hcd 0000:00:13.2: hcca frame #0005
>ohci_hcd 0000:00:13.2: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
>ohci_hcd 0000:00:13.2: roothub.b 00000000 PPCM=0000 DR=0000
>ohci_hcd 0000:00:13.2: roothub.status 00008000 DRWE
>ohci_hcd 0000:00:13.2: roothub.portstatus [0] 0x00000100 PPS
>ohci_hcd 0000:00:13.2: roothub.portstatus [1] 0x00000100 PPS
>usb usb4: default language 0x0409
>usb usb4: uevent
>usb usb4: usb_probe_device
>usb usb4: configuration #1 chosen from 1 choice
>usb usb4: adding 4-0:1.0 (config #1, interface 0)
>usb 4-0:1.0: uevent
>hub 4-0:1.0: usb_probe_interface
>hub 4-0:1.0: usb_probe_interface - got id
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 2 ports detected
>hub 4-0:1.0: standalone hub
>hub 4-0:1.0: no power switching (usb 1.0)
>hub 4-0:1.0: no over-current protection
>hub 4-0:1.0: power on to power good time: 4ms
>hub 4-0:1.0: local power source is good
>hub 4-0:1.0: trying to enable port power on non-switchable hub
>hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
>ehci_hcd 0000:00:13.5: port 4 low speed --> companion
>drivers/usb/core/inode.c: creating file '001'
>usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
>usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>usb usb4: Product: OHCI Host Controller
>usb usb4: Manufacturer: Linux 2.6.26-0.115.rc9.git2.fc10.i686 ohci_hcd
>usb usb4: SerialNumber: 0000:00:13.2
>ohci_hcd 0000:00:13.3: OHCI Host Controller
>drivers/usb/core/inode.c: creating file '005'
>ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
>ohci_hcd 0000:00:13.3: created debug files
>ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe7fb000
>ehci_hcd 0000:00:13.5: GetStatus port 4 status 003002 POWER OWNER sig=se0 CSC
>ehci_hcd 0000:00:13.5: GetStatus port 9 status 001803 POWER sig=j CSC CONNECT
>hub 1-0:1.0: port 9, status 0501, change 0001, 480 Mb/s
>ohci_hcd 0000:00:13.3: OHCI controller state
>ohci_hcd 0000:00:13.3: OHCI 1.0, NO legacy support registers
>ohci_hcd 0000:00:13.3: control 0x083 HCFS=operational CBSR=3
>ohci_hcd 0000:00:13.3: cmdstatus 0x00000 SOC=0
>ohci_hcd 0000:00:13.3: intrstatus 0x00000004 SF
>ohci_hcd 0000:00:13.3: intrenable 0x8000001a MIE UE RD WDH
>ohci_hcd 0000:00:13.3: hcca frame #0005
>ohci_hcd 0000:00:13.3: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
>ohci_hcd 0000:00:13.3: roothub.b 00000000 PPCM=0000 DR=0000
>ohci_hcd 0000:00:13.3: roothub.status 00008000 DRWE
>ohci_hcd 0000:00:13.3: roothub.portstatus [0] 0x00000100 PPS
>ohci_hcd 0000:00:13.3: roothub.portstatus [1] 0x00000100 PPS
>usb usb5: default language 0x0409
>usb usb5: uevent
>usb usb5: usb_probe_device
>usb usb5: configuration #1 chosen from 1 choice
>usb usb5: adding 5-0:1.0 (config #1, interface 0)
>usb 5-0:1.0: uevent
>hub 5-0:1.0: usb_probe_interface
>hub 5-0:1.0: usb_probe_interface - got id
>hub 5-0:1.0: USB hub found
>hub 5-0:1.0: 2 ports detected
>hub 5-0:1.0: standalone hub
>hub 5-0:1.0: no power switching (usb 1.0)
>hub 5-0:1.0: no over-current protection
>hub 5-0:1.0: power on to power good time: 4ms
>hub 5-0:1.0: local power source is good
>hub 5-0:1.0: trying to enable port power on non-switchable hub
>hub 1-0:1.0: debounce: port 9: total 100ms stable 100ms status 0x501
>drivers/usb/core/inode.c: creating file '001'
>usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
>usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>usb usb5: Product: OHCI Host Controller
>usb usb5: Manufacturer: Linux 2.6.26-0.115.rc9.git2.fc10.i686 ohci_hcd
>usb usb5: SerialNumber: 0000:00:13.3
>ohci_hcd 0000:00:13.4: OHCI Host Controller
>drivers/usb/core/inode.c: creating file '006'
>ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
>ohci_hcd 0000:00:13.4: created debug files
>ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe7fa000
>ehci_hcd 0000:00:13.5: port 9 high speed
>ehci_hcd 0000:00:13.5: GetStatus port 9 status 001005 POWER sig=se0 PE CONNECT
>ohci_hcd 0000:00:13.4: OHCI controller state
>ohci_hcd 0000:00:13.4: OHCI 1.0, NO legacy support registers
>ohci_hcd 0000:00:13.4: control 0x083 HCFS=operational CBSR=3
>ohci_hcd 0000:00:13.4: cmdstatus 0x00000 SOC=0
>ohci_hcd 0000:00:13.4: intrstatus 0x00000004 SF
>ohci_hcd 0000:00:13.4: intrenable 0x8000001a MIE UE RD WDH
>ohci_hcd 0000:00:13.4: hcca frame #0005
>ohci_hcd 0000:00:13.4: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
>ohci_hcd 0000:00:13.4: roothub.b 00000000 PPCM=0000 DR=0000
>ohci_hcd 0000:00:13.4: roothub.status 00008000 DRWE
>ohci_hcd 0000:00:13.4: roothub.portstatus [0] 0x00000100 PPS
>ohci_hcd 0000:00:13.4: roothub.portstatus [1] 0x00000100 PPS
>usb usb6: default language 0x0409
>usb usb6: uevent
>usb usb6: usb_probe_device
>usb usb6: configuration #1 chosen from 1 choice
>usb usb6: adding 6-0:1.0 (config #1, interface 0)
>usb 6-0:1.0: uevent
>hub 6-0:1.0: usb_probe_interface
>hub 6-0:1.0: usb_probe_interface - got id
>hub 6-0:1.0: USB hub found
>hub 6-0:1.0: 2 ports detected
>hub 6-0:1.0: standalone hub
>hub 6-0:1.0: no power switching (usb 1.0)
>hub 6-0:1.0: no over-current protection
>hub 6-0:1.0: power on to power good time: 4ms
>hub 6-0:1.0: local power source is good
>hub 6-0:1.0: trying to enable port power on non-switchable hub
>usb 1-9: new high speed USB device using ehci_hcd and address 5
>ehci_hcd 0000:00:13.5: port 9 high speed
>ehci_hcd 0000:00:13.5: GetStatus port 9 status 001005 POWER sig=se0 PE CONNECT
>drivers/usb/core/inode.c: creating file '001'
>usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
>usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>usb usb6: Product: OHCI Host Controller
>usb usb6: Manufacturer: Linux 2.6.26-0.115.rc9.git2.fc10.i686 ohci_hcd
>usb usb6: SerialNumber: 0000:00:13.4
>USB Universal Host Controller Interface driver v3.0
>usb 1-9: default language 0x0409
>usb 1-9: uevent
>usb 1-9: usb_probe_device
>usb 1-9: configuration #1 chosen from 1 choice
>usb 1-9: adding 1-9:1.0 (config #1, interface 0)
>usb 1-9:1.0: uevent
>drivers/usb/core/inode.c: creating file '005'
>usb 1-9: New USB device found, idVendor=058f, idProduct=6362
>usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3
>usb 1-9: Product: Mass Storage Device
>usb 1-9: Manufacturer: Generic
>usb 1-9: SerialNumber: 058F312D81B
>hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0010
>hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0002
>ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
>hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
>ahci 0000:00:12.0: version 3.0
>ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
>hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
>ohci_hcd 0000:00:13.0: port[0] reset timeout, stat 00000111
>ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
>usb 2-1: new full speed USB device using ohci_hcd and address 2
>ohci_hcd 0000:00:13.0: port[0] reset timeout, stat 00000113
>ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
>usb 2-1: uevent
>usb 2-1: usb_probe_device
>usb 2-1: configuration #1 chosen from 1 choice
>usb 2-1: adding 2-1:1.0 (config #1, interface 0)
>usb 2-1:1.0: uevent
>drivers/usb/core/inode.c: creating file '002'
>usb 2-1: New USB device found, idVendor=05d8, idProduct=4002
>usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
>hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0006
>ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
>hub 3-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
>hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
>ohci_hcd 0000:00:13.1: port[0] reset timeout, stat 00000311
>ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
>usb 3-1: new low speed USB device using ohci_hcd and address 2
>ohci_hcd 0000:00:13.1: port[0] reset timeout, stat 00000313
>ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
>usb 3-1: skipped 1 descriptor after interface
>usb 3-1: skipped 1 descriptor after interface
>usb 3-1: default language 0x0409
>usb 3-1: uevent
>usb 3-1: usb_probe_device
>usb 3-1: configuration #1 chosen from 1 choice
>usb 3-1: adding 3-1:1.0 (config #1, interface 0)
>usb 3-1:1.0: uevent
>usbhid 3-1:1.0: usb_probe_interface
>usbhid 3-1:1.0: usb_probe_interface - got id
>input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:13.1/usb3/3-1/3-1:1.0/input/input1
>input,hidraw0: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:13.1-1
>usb 3-1: adding 3-1:1.1 (config #1, interface 1)
>usb 3-1:1.1: uevent
>usbhid 3-1:1.1: usb_probe_interface
>usbhid 3-1:1.1: usb_probe_interface - got id
>input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:13.1/usb3/3-1/3-1:1.1/input/input2
>drivers/usb/core/file.c: looking for a minor, starting at 96
>input,hiddev96,hidraw1: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:13.1-1
>drivers/usb/core/inode.c: creating file '002'
>usb 3-1: New USB device found, idVendor=0603, idProduct=00f2
>usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
>usb 3-1: Product: USB Keyboard
>usb 3-1: Manufacturer: NOVATEK
>ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
>hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
>ohci_hcd 0000:00:13.2: auto-stop root hub
>ohci_hcd 0000:00:13.3: auto-stop root hub
>hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
>ohci_hcd 0000:00:13.1: port[1] reset timeout, stat 00000311
>ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
>usb 3-2: new low speed USB device using ohci_hcd and address 3
>ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
>ahci 0000:00:12.0: flags: ncq sntf ilck led clo pmp pio 
>scsi0 : ahci
>scsi1 : ahci
>scsi2 : ahci
>scsi3 : ahci
>ata1: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ff900 irq 22
>ata2: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ff980 irq 22
>ata3: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ffa00 irq 22
>ata4: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ffa80 irq 22
>ohci_hcd 0000:00:13.1: port[1] reset timeout, stat 00000313
>ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
>ohci_hcd 0000:00:13.4: auto-stop root hub
>usb 3-2: skipped 1 descriptor after interface
>usb 3-2: default language 0x0409
>usb 3-2: uevent
>usb 3-2: usb_probe_device
>usb 3-2: configuration #1 chosen from 1 choice
>usb 3-2: adding 3-2:1.0 (config #1, interface 0)
>usb 3-2:1.0: uevent
>usbhid 3-2:1.0: usb_probe_interface
>usbhid 3-2:1.0: usb_probe_interface - got id
>input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:13.1/usb3/3-2/3-2:1.0/input/input3
>input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:13.1-2
>drivers/usb/core/inode.c: creating file '003'
>usb 3-2: New USB device found, idVendor=046d, idProduct=c043
>usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
>usb 3-2: Product: USB-PS/2 Optical Mouse
>usb 3-2: Manufacturer: Logitech
>hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
>hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
>hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
>hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004
>ata1: softreset failed (device not ready)
>ata1: failed due to HW bug, retry pmp=0
>ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>ata1.00: ATA-8: SAMSUNG HD321KJ, CP100-10, max UDMA7
>ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
>ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
>ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
>ata1.00: configured for UDMA/133
>ata2: softreset failed (device not ready)
>ata2: failed due to HW bug, retry pmp=0
>ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
>ata2.00: ATAPI: TSSTcorp CDDVDW SH-S203P, SB00, max UDMA/100, ATAPI AN
>ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
>ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
>ata2.00: configured for UDMA/100
>ata3: softreset failed (device not ready)
>ata3: failed due to HW bug, retry pmp=0
>ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
>ata3.00: ATA-8: ST3500320AS, SD15, max UDMA/133
>ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
>ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
>ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
>ata3.00: configured for UDMA/133
>hub 4-0:1.0: hub_suspend
>usb usb4: bus auto-suspend
>ohci_hcd 0000:00:13.2: suspend root hub
>hub 5-0:1.0: hub_suspend
>usb usb5: bus auto-suspend
>ohci_hcd 0000:00:13.3: suspend root hub
>hub 6-0:1.0: hub_suspend
>usb usb6: bus auto-suspend
>ohci_hcd 0000:00:13.4: suspend root hub
>ata4: SATA link down (SStatus 0 SControl 300)
>scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD321KJ  CP10 PQ: 0 ANSI: 5
>sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
>sd 0:0:0:0: [sda] Write Protect is off
>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
>sd 0:0:0:0: [sda] Write Protect is off
>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: sda1 sda2 sda3
>sd 0:0:0:0: [sda] Attached SCSI disk
>sd 0:0:0:0: Attached scsi generic sg0 type 0
>scsi 1:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S203P  SB00 PQ: 0 ANSI: 5
>scsi 1:0:0:0: Attached scsi generic sg1 type 5
>scsi 2:0:0:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
>sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
>sd 2:0:0:0: [sdb] Write Protect is off
>sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
>sd 2:0:0:0: [sdb] Write Protect is off
>sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdb: sdb1
>sd 2:0:0:0: [sdb] Attached SCSI disk
>sd 2:0:0:0: Attached scsi generic sg2 type 0
>modprobe used greatest stack depth: 1008 bytes left
>PCI: Setting latency timer of device 0000:00:14.1 to 64
>scsi4 : pata_atiixp
>scsi5 : pata_atiixp
>ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
>ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs: mounted filesystem with ordered data mode.
>SELinux:  Disabled at runtime.
>SELinux:  Unregistering netfilter hooks
>type=1404 audit(1217367829.579:2): selinux=0 auid=4294967295 ses=4294967295
>usb usb2: uevent
>usb 2-0:1.0: uevent
>usb 2-1: uevent
>usb 2-1:1.0: uevent
>usb usb3: uevent
>usb 3-0:1.0: uevent
>usb 3-1: uevent
>usb 3-1:1.0: uevent
>usb 3-1:1.1: uevent
>usb 3-2: uevent
>usb 3-2:1.0: uevent
>usb usb4: uevent
>usb 4-0:1.0: uevent
>usb usb5: uevent
>usb 5-0:1.0: uevent
>usb usb6: uevent
>usb 6-0:1.0: uevent
>usb usb1: uevent
>usb 1-0:1.0: uevent
>usb 1-9: uevent
>usb 1-9:1.0: uevent
>input: PC Speaker as /devices/platform/pcspkr/input/input4
>piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
>r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
>PCI: Setting latency timer of device 0000:02:00.0 to 64
>r8169 0000:02:00.0: no MSI. Back to INTx.
>eth0: RTL8168b/8111b at 0xf88b2000, 00:1b:2f:bc:8a:0f, XID 38000000 IRQ 19
>udev: renamed network interface eth0 to eth1
>Driver 'sr' needs updating - please use bus_type methods
>sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
>Uniform CD-ROM driver Revision: 3.20
>sr 1:0:0:0: Attached scsi CD-ROM sr0
>firewire_ohci: Added fw-ohci device 0000:03:00.0, OHCI version 1.10
>Initializing USB Mass Storage driver...
>usb-storage 1-9:1.0: usb_probe_interface
>usb-storage 1-9:1.0: usb_probe_interface - got id
>scsi6 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 5
>usb-storage: waiting for device to settle before scanning
>usbcore: registered new interface driver usb-storage
>USB Mass Storage support registered.
>ath5k_pci 0000:03:02.0: registered as 'phy0'
>phy0: Selected rate control algorithm 'pid'
>firewire_core: created device fw0: GUID 00dc10000107e440, S400
>ath5k phy0: Atheros AR2413 chip found (MAC: 0x78, PHY: 0x45)
>ALSA sound/pci/hda/hda_intel.c:1990: chipset global capabilities = 0x4401
>ALSA sound/pci/hda/hda_intel.c:748: codec_mask = 0x1
>ALSA sound/pci/hda/hda_codec.c:2347: hda_codec: model '6stack-dig' is selected for config 1462:7327 (MSI)
>ALSA sound/pci/hda/hda_codec.c:1124: Cannot find slave Headphone Playback Volume, skipped
>ALSA sound/pci/hda/hda_codec.c:1124: Cannot find slave Speaker Playback Volume, skipped
>ALSA sound/pci/hda/hda_codec.c:1124: Cannot find slave Mono Playback Volume, skipped
>ALSA sound/pci/hda/hda_codec.c:1124: Cannot find slave Line-Out Playback Volume, skipped
>ALSA sound/pci/hda/hda_codec.c:1124: Cannot find slave Speaker Playback Switch, skipped
>ALSA sound/pci/hda/hda_codec.c:1124: Cannot find slave Mono Playback Switch, skipped
>ALSA sound/pci/hda/hda_intel.c:1990: chipset global capabilities = 0x1001
>ALSA sound/pci/hda/hda_intel.c:748: codec_mask = 0x1
>NET: Registered protocol family 10
>lo: Disabled Privacy Extensions
>[drm] Initialized drm 1.1.0 20060810
>[drm] Initialized radeon 1.29.0 20080528 on minor 0
>usb-storage: device scan complete
>scsi 6:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
>scsi 6:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
>scsi 6:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
>scsi 6:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
>sd 6:0:0:0: [sdc] Attached SCSI removable disk
>sd 6:0:0:0: Attached scsi generic sg3 type 0
>sd 6:0:0:1: [sdd] Attached SCSI removable disk
>sd 6:0:0:1: Attached scsi generic sg4 type 0
>sd 6:0:0:2: [sde] Attached SCSI removable disk
>sd 6:0:0:2: Attached scsi generic sg5 type 0
>sd 6:0:0:3: [sdf] Attached SCSI removable disk
>sd 6:0:0:3: Attached scsi generic sg6 type 0
>[drm] Setting GART location based on new memory map
>[drm] Loading RS690 Microcode
>[drm] Num pipes: 1
>[drm] writeback test succeeded in 1 usecs
>device-mapper: uevent: version 1.0.3
>device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
>device-mapper: multipath: version 1.0.5 loaded
>EXT3 FS on sda1, internal journal
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sda3, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sdb1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>Adding 2096472k swap on /dev/sda2.  Priority:-1 extents:1 across:2096472k

Actions: View

Attachments on bug 457250: 313003 | 321528 | 321530