| Summary: | s390x device has ipv6 setup even if profile has ipv6.ignore | ||
|---|---|---|---|
| Product: | Red Hat Enterprise Linux 7 | Reporter: | Vladimir Benes <vbenes> |
| Component: | NetworkManager | Assignee: | Thomas Haller <thaller> |
| Status: | CLOSED NOTABUG | QA Contact: | Desktop QE <desktop-qa-list> |
| Severity: | medium | Docs Contact: | |
| Priority: | medium | ||
| Version: | 7.3 | CC: | aloughla, atragler, bgalvani, lrintel, mleitner, rkhan, sukulkar, thaller |
| Target Milestone: | rc | ||
| Target Release: | --- | ||
| Hardware: | Unspecified | ||
| OS: | Unspecified | ||
| Whiteboard: | |||
| Fixed In Version: | Doc Type: | Bug Fix | |
| Doc Text: | Story Points: | --- | |
| Clone Of: | Environment: | ||
| Last Closed: | 2016-11-25 13:48:18 UTC | Type: | Bug |
| Regression: | --- | Mount Type: | --- |
| Documentation: | --- | CRM: | |
| Verified Versions: | Category: | --- | |
| oVirt Team: | --- | RHEL 7.3 requirements from Atomic Host: | |
| Cloudforms Team: | --- | Target Upstream Version: | |
There is currently no ipv6.method=disabled. There is "ignore", but ignore means just, don't touch, leave it to the kernel. As such, I think this is expected behavior. NM just didn't reset the ipv6 sysctl values from whatever was set before NetworkManager starts. |
Description of problem: I have a clean install profile (generated by dracut) that has no ipv6 section. [root@ibm-z10-29 ~]# cat /etc/sysconfig/network-scripts/ifcfg-enccw0.0.8000 # Generated by dracut initrd NAME="enccw0.0.8000" SUBCHANNELS="0.0.8000,0.0.8001,0.0.8002" NETTYPE="qeth" OPTIONS="layer2=1 portname=z10-29 portno=0" DEVICE="enccw0.0.8000" ONBOOT=yes NETBOOT=yes UUID="f4d76d82-cfbe-4290-a04a-9a6caf111308" BOOTPROTO=none IPADDR="10.16.66.220" PREFIX="21" GATEWAY="10.16.71.254" TYPE=Ethernet DNS1="10.11.5.19" but I have ipv6 correctly set 2: enccw0.0.8000: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000 link/ether 02:de:ad:be:ef:1d brd ff:ff:ff:ff:ff:ff inet 10.16.66.220/21 brd 10.16.71.255 scope global enccw0.0.8000 valid_lft forever preferred_lft forever inet6 2620:52:0:1040:de:adff:febe:ef1d/64 scope global mngtmpaddr dynamic valid_lft 2591957sec preferred_lft 604757sec inet6 fe80::de:adff:febe:ef1d/64 scope link valid_lft forever preferred_lft forever NM up and running: [root@ibm-z10-29 ~]# systemctl status NetworkManager ● NetworkManager.service - Network Manager Loaded: loaded (/usr/lib/systemd/system/NetworkManager.service; enabled; vendor preset: enabled) Active: active (running) since Fri 2016-02-19 02:59:06 EST; 16min ago Main PID: 13600 (NetworkManager) CGroup: /system.slice/NetworkManager.service └─13600 /usr/sbin/NetworkManager --no-daemon shouldn't be ipv6 disabled? this is because this is set, right? [root@ibm-z10-29 ~]# sysctl -a |grep ipv6|grep encc net.ipv6.conf.enccw0/0/8000.accept_dad = 1 net.ipv6.conf.enccw0/0/8000.accept_ra = 1 net.ipv6.conf.enccw0/0/8000.accept_ra_defrtr = 1 net.ipv6.conf.enccw0/0/8000.accept_ra_pinfo = 1 net.ipv6.conf.enccw0/0/8000.accept_ra_rt_info_max_plen = 0 net.ipv6.conf.enccw0/0/8000.accept_ra_rtr_pref = 1 Is this a bug or not? I suppose these values are set differently on x86_64. [root@wlan-r2s22 ~]# sysctl -a |grep eth0|grep ipv6 net.ipv6.conf.eth0.accept_dad = 1 net.ipv6.conf.eth0.accept_ra = 1 net.ipv6.conf.eth0.accept_ra_defrtr = 0 net.ipv6.conf.eth0.accept_ra_pinfo = 0 net.ipv6.conf.eth0.accept_ra_rt_info_max_plen = 0 net.ipv6.conf.eth0.accept_ra_rtr_pref = 0 no matter if method is ignore or auto. But this makes a difference as when ra is enabled s390x obtains ipv6 addresses but x86_64 not. Shouldn't this be consistent? Version-Release number of selected component (if applicable): NetworkManager-1.0.6-27.el7.x86_64