Bug 2276664

+++ This bug was initially created as a clone of Bug #2273533 +++

Description of problem (please be detailed as possible and provide log
snippests):
Created RDR test environment with 5 OCP clusters. Cluster hyper2 is the hub with ACM and 2 sets of managed clusters; hyper3<->hyper4 and hyper5<->hyper6. All 4 clusters had ODF 4.15 installed. 

After getting clusters imported into ACM and configuring Submariner between the peer clusters MCO was installed and the first DRPolicy created between hyper3<->hyper4. I validated that mirroring was enabled, object buckets created, DR cluster operators installed, and secrets exchanged. 

I then attempted to create a 2nd DRPolicy for hyper5<->hyper6. This fails with a webhook error (graphic attached). The only resource created was the new DRPolicy on the hub (hyper2) cluster.

Version of all relevant components (if applicable):
OCP 4.15.3
ODF 4.15.0
ACM 2.10.0
Submariner 0.17

Does this issue impact your ability to continue to work with the product
(please explain in detail what is the user impact)?
Yes, DR is not configured for 2nd set of Peer clusters

Is there any workaround available to the best of your knowledge?
No

Rate from 1 - 5 the complexity of the scenario you performed that caused this
bug (1 - very simple, 5 - very complex)?
4

Can this issue reproducible?
Only tested one time

Can this issue reproduce from the UI?
Yes

Steps to Reproduce:
1. Create RDR config with hub + 4 managed clusters (2 Peer clusters)
2. Create DRPolicy for first Peer Cluster and validate
3. Create DRPolicy for second Peer Cluster


Actual results:
There is UI error in Create DRPolicy and only drpolicy is created

Expected results:
There is no UI error and DR configuration is created exactly the same as first Peer Cluster for second set of cluster (2nd Peer Cluster).

--- Additional comment from RHEL Program Management on 2024-04-04 21:08:18 UTC ---

This bug having no release flag set previously, is now set with release flag 'odf‑4.16.0' to '?', and so is being proposed to be fixed at the ODF 4.16.0 release. Note that the 3 Acks (pm_ack, devel_ack, qa_ack), if any previously set while release flag was missing, have now been reset since the Acks are to be set against a release flag.

--- Additional comment from RHEL Program Management on 2024-04-04 21:08:18 UTC ---

The 'Target Release' is not to be set manually at the Red Hat OpenShift Data Foundation product.

The 'Target Release' will be auto set appropriately, after the 3 Acks (pm,devel,qa) are set to "+" for a specific release flag and that release flag gets auto set to "+".

--- Additional comment from Annette Clewett on 2024-04-04 21:09:49 UTC ---



--- Additional comment from Vineet on 2024-04-17 08:35:30 UTC ---

@aclewett I am unable to replicate it on my cluster. It seems to be an intermittent network issue. Can you retry after giving the operator pod a restart ?

--- Additional comment from Annette Clewett on 2024-04-17 21:42:20 UTC ---

@vbadrina I completely started over with ODF 4.15.1 and reinstalled MCO and updated ODF on the managed clusters. This time the first DRPolicy was between hyper5 and hyper6 which had failed before with UI issue. The DRPolicy went to Validated in ~5 mins. 

The 2nd DRPolicy was for hyper2 and hyper3 which failed immediately as the 2nd DRPolicy with the UI error (attached to BZ). It seems that this is not a network issue. Are you reproducing using ACM 2.10.1 and the odf-multicluster plugin via Data policies UI?