Bug 2517101 (CVE-2026-74555)
| Summary: | CVE-2026-74555 kernel: scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake race | ||
|---|---|---|---|
| Product: | [Other] Security Response | Reporter: | OSIDB Bzimport <bzimport> |
| Component: | vulnerability | Assignee: | Product Security DevOps Team <prodsec-dev> |
| Status: | NEW --- | QA Contact: | |
| Severity: | medium | Docs Contact: | |
| Priority: | medium | ||
| Version: | unspecified | CC: | rhel-process-autobot, watson-tool-maintainers |
| Target Milestone: | --- | Keywords: | Security |
| Target Release: | --- | ||
| Hardware: | All | ||
| OS: | Linux | ||
| Whiteboard: | |||
| Fixed In Version: | Doc Type: | --- | |
| Doc Text: |
A flaw was found in the `scsi: libsas` component of the Linux kernel. A deadlock can occur during the system resume process, preventing the host from becoming fully operational. Additionally, a race condition can cause the controller to suspend prematurely while disks are still waking up. This can lead to disk input/output (I/O) operations failing and the affected disks becoming disabled, resulting in a denial of service (DoS).
|
Story Points: | --- |
| Clone Of: | Environment: | ||
| Last Closed: | Type: | --- | |
| Regression: | --- | Mount Type: | --- |
| Documentation: | --- | CRM: | |
| Verified Versions: | Category: | --- | |
| oVirt Team: | --- | RHEL 7.3 requirements from Atomic Host: | |
| Cloudforms Team: | --- | Target Upstream Version: | |
| Embargoed: | |||
In the Linux kernel, the following vulnerability has been resolved: scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake race Commit fbefe22811c3 ("scsi: libsas: Don't always drain event workqueue for HA resume") introduced sas_resume_ha_no_sync() to avoid a deadlock: the PHYE_RESUME_TIMEOUT handler, running on the HA event workqueue, calls sas_deform_port() -> sas_destruct_devices(), which removes SCSI devices and waits for the host to become runtime-active. But the host cannot resume until sas_resume_ha() -> sas_drain_work() returns, and the drain is blocked on that very handler. However skipping the drain reintroduces a race: hisi_sas returns from resume before all PHY UP work and libsas discovery work finish. The controller may then autosuspend while disks are still waking up. The disks issue IO to a suspended controller, the IO fails, and the disks get disabled. Fix the deadlock at its source by moving the PHYE_RESUME_TIMEOUT notification to after sas_drain_work(). By then the host resume is about to complete, so device removal through device_link no longer blocks on the resume and the cycle is broken. With the deadlock gone, restore sas_resume_ha() (the draining variant) in hisi_sas and remove sas_resume_ha_no_sync(). The reorder is safe for the other libsas consumers (isci, pm8001, aic94xx, mvsas). During suspend, sas_suspend_devices() calls sas_notify_lldd_dev_gone() for each device, which sets dev->lldd_dev to NULL. When scsi_unblock_requests re-enables I/O in resume, any I/O to a timed-out phy's disk is immediately rejected by the LLDD before reaching hardware: isci returns SAS_DEVICE_UNKNOWN (mapped to DID_BAD_TARGET), and pm8001 returns SAS_PHY_DOWN (mapped to DID_NO_CONNECT). Both complete directly via scsi_done() without entering SCSI EH. This is identical in both the old and new ordering since lldd_dev_gone runs during suspend, before resume. The reorder only affects when the PHYE_RESUME_TIMEOUT handler runs (synchronized by sas_drain_work() vs. asynchronous after resume returns), not whether I/O can reach the device. aic94xx and mvsas do not register any PM ops and never reach this code path.