Bug 74714
| Summary: | traceback WirelessInterface:on_hw_config_page_next:204 | ||
|---|---|---|---|
| Product: | [Retired] Red Hat Linux | Reporter: | R P Herrold <herrold> |
| Component: | redhat-config-network | Assignee: | Harald Hoyer <harald> |
| Status: | CLOSED RAWHIDE | QA Contact: | |
| Severity: | medium | Docs Contact: | |
| Priority: | medium | ||
| Version: | 8.0 | CC: | wtogami |
| Target Milestone: | --- | ||
| Target Release: | --- | ||
| Hardware: | i386 | ||
| OS: | Linux | ||
| Whiteboard: | |||
| Fixed In Version: | Doc Type: | Bug Fix | |
| Doc Text: | Story Points: | --- | |
| Clone Of: | Environment: | ||
| Last Closed: | 2003-01-30 16:16:35 UTC | Type: | --- |
| Regression: | --- | Mount Type: | --- |
| Documentation: | --- | CRM: | |
| Verified Versions: | Category: | --- | |
| oVirt Team: | --- | RHEL 7.3 requirements from Atomic Host: | |
| Cloudforms Team: | --- | Target Upstream Version: | |
| Embargoed: | |||
| Bug Depends On: | |||
| Bug Blocks: | 81720 | ||
The PCI card is an older carrier, well made (Dell marque), for the Aironet pc-card I then manually modprobed in airo, and re-ran the tool. The wireless card appeared (improperly) at eth0 the first time shown -- but going past the incorrect setting to the next screen, and then using Back, caused it to re-appear at the proper interface (eth1). Finally, it is throwing (hamless<?>) errors into the console thus: Warning : Device eth1 has been compiled with version 13 of Wireless Extension, while we are using version 12. Some things may be broken... airo: Probing for PCI adapters airo: Doing fast bap_reads divert: allocating divert_blk for eth1 airo: MAC enabled eth1 0:40:96:31:6c:69 airo: Finished probing for PCI adapters bash-2.05b$
bash-2.05b$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:00:21:40:0B:E7
inet addr:172.16.33.101 Bcast:172.16.33.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:604 errors:0 dropped:0 overruns:0 frame:0
TX packets:466 errors:0 dropped:0 overruns:0 carrier:0
collisions:2 txqueuelen:100
RX bytes:469243 (458.2 Kb) TX bytes:57741 (56.3 Kb)
Interrupt:10 Base address:0x10e0
eth1 Link encap:Ethernet HWaddr 00:40:96:31:6C:69
inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:8 dropped:0 overruns:0 carrier:8
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:2504 (2.4 Kb)
Interrupt:5 Base address:0x1080
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:78008 errors:0 dropped:0 overruns:0 frame:0
TX packets:78008 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:15072642 (14.3 Mb) TX bytes:15072642 (14.3 Mb)
bash-2.05b$ iwconfig eth1
eth1 IEEE 802.11-DS ESSID:"" Nickname:"couch"
Mode:Managed Frequency:2.412GHz Access Point: FF:FF:FF:FF:FF:FF
Bit Rate=11Mb/s Tx-Power=15 dBm Sensitivity=0/65535
Retry limit:16 RTS thr:off Fragment thr:off
Power Management:off
Link Quality:0/10 Signal level:-96 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
bash-2.05b$
|
Traceback (most recent call last): File "/usr/sbin/../share/redhat-config-network/netconfpkg/gui/WirelessInterface.py", line 204, in on_hw_config_page_next self.hw_sel = clist.selection[0] IndexError: list index out of range =========================== 00:0e.0 Network controller: AIRONET Wireless Communications PC4800 (rev 01) Flags: medium devsel, IRQ 5 Memory at e0008000 (32-bit, non-prefetchable) [size=128] I/O ports at 1000 [size=128] I/O ports at 1080 [size=64]