Hide Forgot
Description of problem: Update of 03-Nov-2013 (was 'current' until this date) installed abrt updates + firmware (?). Post installation, "ath: phy0:" error messages streaming into system message log (viewable with 'dmesg') continuously. Disabling wifi does not quiet error reporting. 2Ghz is connectable but with error streaming. 5Ghz is not connectable. Version-Release number of selected component (if applicable): How reproducible: install current version, enable wifi and attempt to connect to wifi (2 or 5 Ghz). Steps to Reproduce: 1. install current updates as of 03-Nov-2013 and boot existing config using 5 Ghz network. 2. open back side tty (tty2, etc) 3. log in. 4. Errors start streaming as soon as logged in. Actual results: (sample cut/paste from message log) [17770.855258] ath: phy0: Failed to wakeup in 500us [17770.966496] ath: phy0: RX failed to go idle in 10 ms RXSM=0xffffffff [17770.977603] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7= 0xffffffff streamed nearly continuously down every active tty login session. System is 'jumpy' post installation of updates (keyboard input at gnome desktop and other ttys noticably delayed before echoing. Expected results: No such errors reported prior to this update. Additional info: Submitter will be happy to provide whatever is needed (including full package install list). Submitter uncertain what to include at time of bug report.
Submitter uncertain if actual cause is 9170 firmware. attempt to comb through for exact package name. assistance assisted. full cut/past of repeated text from /var/log/messages below -- begin -- Nov 3 22:38:57 lizum kernel: [14778.006915] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up Nov 3 22:38:58 lizum kernel: [14778.117972] ath: phy0: Chip reset failed Nov 3 22:38:58 lizum kernel: [14778.117973] ath: phy0: Unable to reset channel, reset status -22 Nov 3 22:38:58 lizum kernel: [14778.117980] ath: phy0: Unable to set channel Nov 3 22:38:58 lizum kernel: [14778.178737] ath: phy0: Failed to stop TX DMA, queues=0x18f! Nov 3 22:38:58 lizum kernel: [14778.189837] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff -- end --
Corrected improper reference to 9170_firmware. aic94xx firmware (?) Current installed 'firmware' files are: ql23xx-firmware-3.03.28-5.fc19.noarch iwl5000-firmware-8.83.5.1_1-29.fc19.noarch alsa-firmware-1.0.27-1.fc19.noarch iwl100-firmware-39.31.5.1-29.fc19.noarch iwl6000g2b-firmware-17.168.5.2-29.fc19.noarch ipw2100-firmware-1.3-15.fc19.noarch ql2200-firmware-2.02.08-7.fc19.noarch libertas-usb8388-firmware-20130724-29.git31f6b30.fc19.noarch ivtv-firmware-20080701-24.noarch atmel-firmware-1.3-11.fc19.noarch iwl4965-firmware-228.61.2.24-29.fc19.noarch iwl135-firmware-18.168.6.1-29.fc19.noarch iwl105-firmware-18.168.6.1-29.fc19.noarch iwl6050-firmware-41.28.5.1-29.fc19.noarch iwl6000g2a-firmware-17.168.5.3-29.fc19.noarch ql2100-firmware-1.19.38-7.fc19.noarch aic94xx-firmware-30-5.fc19.noarch iwl1000-firmware-39.31.5.1-29.fc19.noarch iwl2030-firmware-18.168.6.1-29.fc19.noarch zd1211-firmware-1.4-8.fc19.noarch iwl3945-firmware-15.32.2.9-29.fc19.noarch iwl6000-firmware-9.221.4.1-29.fc19.noarch ipw2200-firmware-3.1-8.fc19.noarch crystalhd-firmware-3.10.0-4.fc19.noarch iwl5150-firmware-8.24.2.2-29.fc19.noarch linux-firmware-20130724-29.git31f6b30.fc19.noarch alsa-tools-firmware-1.0.27-2.fc19.x86_64 iwl2000-firmware-18.168.6.1-29.fc19.noarch
Hi Chuck, a few questions: - Can you please give us the output of 'ethtool -i ath0'? (I assume that is the name of the interface - Can you also give us the output of 'lspci -v -n' - Can you give us the exact kernel versions (via the 'uname -a' command) in which the card worked and the versions in which the card does not work? Thanks, Michele
Michele, I am currently booted with kernel: 3.11.7-200.fc19.x86_64 and can verify it now only works at 2.4 Ghz. It cannot even find the 5 Ghz network. The oldest kernel I have here now (thanks to updates) is 3.11.6-200.fc19.x86_64 and it does not work for any of my current 3. It worked for me prior to these versions. I'm trying to recall which is the last working version. It most likely is the kernel which was 'current' as of Oct 25. My automatic update (all default settings) ran on the 2nd/3rd and that is where I discovered the problem. I am certain it works in at least one of the 3.10 and 3.9 kernels and wish I had it here to provide the exact version info. I know it works in the version of the kernel on my September distro DVD iso. I can boot that using an external drive if you wish also. If there is a way I can obtain the older kernel revs, I will install them and verify where it works and where it doesn't for you. 'ethtool -i ath0' now gives no results. Nor does wlan0 (a previous/old name). It does show up, with very minimal data, as 'wlp7s0' and yields: [chuck@Lizum /etc]# ethtool -i wlp7s0 driver: ath9k version: 3.11.7-200.fc19.x86_64 firmware-version: N/A bus-info: 0000:07:00.0 supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no [chuck@Lizum /etc]# Subsequently, 'lspci -v -n' yields: 00:00.0 0600: 8086:0154 (rev 09) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:01.0 0604: 8086:0151 (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=06, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: d0000000-d1ffffff Prefetchable memory behind bridge: 00000000b0000000-00000000cfffffff Capabilities: [88] Subsystem: 104d:9097 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Capabilities: [d94] #19 Kernel driver in use: pcieport 00:14.0 0c03: 8086:1e31 (rev 04) (prog-if 30 [XHCI]) Subsystem: 104d:9097 Flags: bus master, medium devsel, latency 0, IRQ 42 Memory at d2300000 (64-bit, non-prefetchable) [size=64K] Capabilities: [70] Power Management version 2 Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+ Kernel driver in use: xhci_hcd 00:16.0 0780: 8086:1e3a (rev 04) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at d2314000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Kernel driver in use: mei_me 00:1a.0 0c03: 8086:1e2d (rev 04) (prog-if 20 [EHCI]) Subsystem: 104d:9097 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at d2319000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci-pci 00:1b.0 0403: 8086:1e20 (rev 04) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at d2310000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: snd_hda_intel 00:1c.0 0604: 8086:1e10 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 Memory behind bridge: d2200000-d22fffff Prefetchable memory behind bridge: 00000000d2500000-00000000d25fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: 104d:9097 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport 00:1c.1 0604: 8086:1e12 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 Memory behind bridge: d2100000-d21fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: 104d:9097 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport 00:1c.2 0604: 8086:1e14 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=0e, subordinate=0e, sec-latency=0 I/O behind bridge: 00002000-00002fff Prefetchable memory behind bridge: 00000000d2000000-00000000d20fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: 104d:9097 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport 00:1d.0 0c03: 8086:1e26 (rev 04) (prog-if 20 [EHCI]) Subsystem: 104d:9097 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at d2318000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci-pci 00:1f.0 0601: 8086:1e59 (rev 04) Subsystem: 104d:9097 Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel driver in use: lpc_ich 00:1f.2 0106: 8086:1e03 (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: 104d:9097 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 41 I/O ports at 4048 [size=8] I/O ports at 4054 [size=4] I/O ports at 4040 [size=8] I/O ports at 4050 [size=4] I/O ports at 4020 [size=32] Memory at d2317000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA v1.0 Capabilities: [b0] PCI Advanced Features Kernel driver in use: ahci 00:1f.3 0c05: 8086:1e22 (rev 04) Subsystem: 104d:9097 Flags: medium devsel, IRQ 19 Memory at d2315000 (64-bit, non-prefetchable) [size=256] I/O ports at 4000 [size=32] 01:00.0 0300: 10de:0de8 (rev a1) (prog-if 00 [VGA controller]) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at d0000000 (32-bit, non-prefetchable) [size=16M] Memory at b0000000 (64-bit, prefetchable) [size=256M] Memory at c0000000 (64-bit, prefetchable) [size=32M] I/O ports at 3000 [size=128] Expansion ROM at c2000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau 01:00.1 0403: 10de:0bea (rev a1) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d1000000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel 07:00.0 0280: 168c:0032 (rev 01) Subsystem: 105b:e044 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at d2200000 (64-bit, non-prefetchable) [size=512K] Expansion ROM at d2500000 [disabled] [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/4 Maskable+ 64bit+ Capabilities: [70] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel driver in use: ath9k 08:00.0 0805: 1180:e822 (rev 09) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d2102000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Power Management version 3 Capabilities: [80] Express Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [800] Advanced Error Reporting Kernel driver in use: sdhci-pci 08:00.1 0880: 1180:e232 (rev 06) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0, IRQ 11 Memory at d2101000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Power Management version 3 Capabilities: [80] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting 08:00.3 0c00: 1180:e832 (rev 05) (prog-if 10 [OHCI]) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at d2100000 (32-bit, non-prefetchable) [size=2K] Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Power Management version 3 Capabilities: [80] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Kernel driver in use: firewire_ohci 0e:00.0 0200: 10ec:8168 (rev 07) Subsystem: 104d:9097 Flags: bus master, fast devsel, latency 0, IRQ 44 I/O ports at 2000 [size=256] Memory at d2004000 (64-bit, prefetchable) [size=4K] Memory at d2000000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Capabilities: [d0] Vital Product Data Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel driver in use: r8169 [chuck@Lizum chuck]#
Thanks Chuck, this gives us a bit more context. You can always find all the kernels built for Fedora on koji.fedoraproject.org: http://koji.fedoraproject.org/koji/packageinfo?packageID=8 As a quick try, you could give the very latest kernel a shot: http://koji.fedoraproject.org/koji/buildinfo?buildID=478832 Note that this is a very experimental kernel with a lot of debugging output which will make it slower. But for a quick test it's ok. You could try downloading kernel-3...x86_64 and add it to your list of kernels via 'rpm -ivh kernel-3..' If you can boot successfully in the above kernel you could check if the issue has already been fixed upstream. If it fixes it we know that upstream has already tackled the issue. If it does not we will need to raise it upstream. hth, Michele
Michele, I don't know why I didn't bother to check this before but I clearly didn't else I'd have reported it straight away. With the wifi connected, claiming: "Signal Strength Good, Link speed 54 Mb/s, Security WPA2, IP: .. " in Network Manager's GUI, the *measured* throughput on the 2.4 Ghz link attempting to copy a file yields some interesting fluctuations from 100KB/sec -> 990 KB/sec (~1-8 Mb/s) with it staying at the 1Mbit rate (very close to) most of the time. That appears something is misidentified isn't it? Interesting? Chuck
Well throughput on Wireless networks is always a mix of marketing and real-life fluctuations. It might very well be that something is misidentified (at NM level, driver level, etc) but we'd need an extremely simple and reproduceable testcase to prove it/investigate further. So with the latest 3.12.x kernels, what issues besides throughput measurements are still open with ath0?
With the latest 3.12.x kernels, specifically 3.12.5-200.fc19.x86_64, there are multiple, easily recreatable and testable issues. My supporting hardware: Netgear D6200 (802.11ac on both 2.4 and 5Ghz) -or- Apple Airport Extreme (2.4 and 5 Ghz with 300n) Synology NAS (4x 1GB wired ethernet supplying data to feed the wifi) I boot this computer on Windows 7 64-bit professional and pull a file from the NAS (copy). Open browser (shared directory on NAS) and browse for file, copy to desktop, done. No fuss. Boot this same computer on this kernel and a) can only find the 2.4G network b) can't even see the 5G network. Copying the same file from the NAS either runs at 1-4 KB/sec or simply fails to start. (nautilus copy) To summarize, is this issue still open? YES. I booted the August/September Installation DVD (i made from the ISO). It works!
Hi Chuck, ok. Can we try the following please: 1) echo "options ath9k nohwcrypt=1" > /etc/modprobe.d/ath9k.conf rmmod ath9k (or reboot) and modprobe ath9k Does the performance issue still persist? 2) If 1) changed nothing, does the following help the performance issue? iwconfig ath0 power off iw dev ath0 set power_save off Thanks, Michele
Hi Michelle, Ok, status report. Step 1: a. file /etc/modprobe.d/ath9k.conf did not exist. Created it. b. rmmod ath9k and modprobe ath9k done ok. Performance on empty wifi (everything else physically powered off), LOS 3 feet (1m) from router: 1.4MB/sec (nautilus) sustained, steady. That is a slight improvement since it wasn't down in the KB range but it's not been running long either. Step 2: a. iwconfig and iw could not find ath0. b. device ath0 listed as 'wlp7s0' c. issued power off command via iw with substituted name d. attempt to set power_save failed (no such device) e. device wlp7s0 still shows active in ifconfig (see below) [chuck@Lizum modprobe.d]# rmmod ath9k [chuck@Lizum modprobe.d]# modprobe ath9k [chuck@Lizum modprobe.d]# iwconfig ath0 power off Error for wireless request "Set Power Management" (8B2C) : SET failed on device ath0 ; No such device. [chuck@Lizum modprobe.d]# ifconfig lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 0 (Local Loopback) RX packets 378922 bytes 302376808 (288.3 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 378922 bytes 302376808 (288.3 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 p2p1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::32f9:edff:fe42:6a7b prefixlen 64 scopeid 0x20<link> ether 30:f9:ed:42:6a:7b txqueuelen 1000 (Ethernet) RX packets 7135784 bytes 2716861925 (2.5 GiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 14561223 bytes 18266719478 (17.0 GiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 wlp7s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.43 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fe80::a617:31ff:feec:91ed prefixlen 64 scopeid 0x20<link> ether a4:17:31:ec:91:ed txqueuelen 1000 (Ethernet) RX packets 61044 bytes 87232966 (83.1 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 20772 bytes 4366148 (4.1 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 [chuck@Lizum modprobe.d]# iwconfig wlp7s0 power off [chuck@Lizum modprobe.d]# iw dev wlp7so power_save off command failed: No such device (-19) Does this help you narrow it down? Chuck
Hi Chuck, well it's some form of progress ;) Ok so adding "nohwcrypt=1" at least brings the speed from KB/sec range to ~1.4MB/sec. I believe Step 2 failed due to the name of the device (0 vs o). If you do: iwconfig wlp7s0 power off iw dev wlp7s0 power_save off and then launch 'iwconfig' you should be able to verify that power management is off with the line: Power Management:off Can you retry step 2 and report what speeds you get? Also during the tests, do you get any messages in /var/log/messages? If yes, could you upload it here? As a side note there are some commits in 3.13 for ath9k which seem to affect this specific chipset: * 2d22c7d - (2013-11-11 14:47:45 -0500) ath9k: Use correct PCIE initvals for AR9485 <Sujith Manoharan> * 7c9a720 - (2013-09-26 15:13:31 -0400) ath9k: Update AR9485 1.1 initvals <Sujith Manoharan> Let's try step 2 and then if things are still no good, we can give the above commits a shot. Thanks and regards, Michele
Michele, I did see my typo *immediately* after I clicked it (and felt like an idiot) I confirm the atheros has power management turned off. iwconfig does confirm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:12 Invalid misc:30 Missed beacon:0 which is what we expect. Aside from the other normal messages the log, the only entries for wlp7s0, which look normal to me are (using 'cat messages | grep wlp7s0 > /tmp/wlp7s0.log'): ------------------------------ [chuck@Lizum log.49]$ cat /tmp/wlp7s0.log Dec 26 13:30:51 lizum NetworkManager[784]: <info> (wlp7s0): using nl80211 for WiFi device control Dec 26 13:30:51 lizum NetworkManager[784]: <info> (wlp7s0): driver supports Access Point (AP) mode Dec 26 13:30:51 lizum NetworkManager[784]: <info> (wlp7s0): new 802.11 WiFi device (driver: 'ath9k' ifindex: 3) Dec 26 13:30:51 lizum NetworkManager[784]: <info> (wlp7s0): exported as /org/freedesktop/NetworkManager/Devices/0 Dec 26 13:30:51 lizum NetworkManager[784]: <info> (wlp7s0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2] Dec 26 13:30:51 lizum NetworkManager[784]: <info> (wlp7s0): bringing up device. Dec 26 13:30:51 lizum NetworkManager[784]: <info> (wlp7s0): preparing device. Dec 26 13:30:51 lizum NetworkManager[784]: <info> (wlp7s0): deactivating device (reason 'managed') [2] Dec 26 13:30:51 lizum kernel: [ 17.595224] IPv6: ADDRCONF(NETDEV_UP): wlp7s0: link is not ready Dec 26 13:30:52 lizum NetworkManager[784]: <info> (wlp7s0) supports 4 scan SSIDs Dec 26 13:30:52 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: starting -> ready Dec 26 13:30:52 lizum NetworkManager[784]: <info> (wlp7s0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] Dec 26 13:30:52 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: ready -> disconnected Dec 26 13:30:52 lizum NetworkManager[784]: <info> (wlp7s0) supports 4 scan SSIDs Dec 26 13:30:53 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: disconnected -> inactive Dec 26 13:30:53 lizum NetworkManager[784]: <info> Activation (wlp7s0) starting connection 'HoheMunde' Dec 26 13:30:53 lizum NetworkManager[784]: <info> (wlp7s0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Dec 26 13:30:53 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 1 of 5 (Device Prepare) scheduled... Dec 26 13:30:53 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 1 of 5 (Device Prepare) started... Dec 26 13:30:53 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 2 of 5 (Device Configure) scheduled... Dec 26 13:30:53 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 1 of 5 (Device Prepare) complete. Dec 26 13:30:53 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 2 of 5 (Device Configure) starting... Dec 26 13:30:53 lizum NetworkManager[784]: <info> (wlp7s0): device state change: prepare -> config (reason 'none') [40 50 0] Dec 26 13:30:53 lizum NetworkManager[784]: <info> Activation (wlp7s0/wireless): connection 'HoheMunde' has security, and secrets exist. No new secrets needed. Dec 26 13:30:53 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 2 of 5 (Device Configure) complete. Dec 26 13:30:53 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: inactive -> scanning Dec 26 13:30:54 lizum kernel: [ 20.272907] wlp7s0: authenticate with 44:94:fc:e5:2b:50 Dec 26 13:30:54 lizum kernel: [ 20.291998] wlp7s0: send auth to 44:94:fc:e5:2b:50 (try 1/3) Dec 26 13:30:54 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: scanning -> authenticating Dec 26 13:30:54 lizum kernel: [ 20.294012] wlp7s0: authenticated Dec 26 13:30:54 lizum kernel: [ 20.294254] wlp7s0: associate with 44:94:fc:e5:2b:50 (try 1/3) Dec 26 13:30:54 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: authenticating -> associating Dec 26 13:30:54 lizum kernel: [ 20.302763] wlp7s0: RX AssocResp from 44:94:fc:e5:2b:50 (capab=0x11 status=0 aid=4) Dec 26 13:30:54 lizum kernel: [ 20.302795] wlp7s0: associated Dec 26 13:30:54 lizum kernel: [ 20.302804] IPv6: ADDRCONF(NETDEV_CHANGE): wlp7s0: link becomes ready Dec 26 13:30:55 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: associating -> associated Dec 26 13:30:55 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: associated -> 4-way handshake Dec 26 13:30:55 lizum NetworkManager[784]: <info> (wlp7s0): supplicant interface state: 4-way handshake -> completed Dec 26 13:30:55 lizum NetworkManager[784]: <info> Activation (wlp7s0/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'HoheMunde'. Dec 26 13:30:55 lizum avahi-daemon[625]: Registering new address record for fe80::a617:31ff:feec:91ed on wlp7s0.*. Dec 26 13:30:55 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 3 of 5 (IP Configure Start) scheduled. Dec 26 13:30:55 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 3 of 5 (IP Configure Start) started... Dec 26 13:30:55 lizum NetworkManager[784]: <info> (wlp7s0): device state change: config -> ip-config (reason 'none') [50 70 0] Dec 26 13:30:55 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Dec 26 13:30:55 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 3 of 5 (IP Configure Start) complete. Dec 26 13:30:55 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 5 of 5 (IPv4 Commit) started... Dec 26 13:30:55 lizum avahi-daemon[625]: Joining mDNS multicast group on interface wlp7s0.IPv4 with address 192.168.1.43. Dec 26 13:30:55 lizum avahi-daemon[625]: New relevant interface wlp7s0.IPv4 for mDNS. Dec 26 13:30:55 lizum avahi-daemon[625]: Registering new address record for 192.168.1.43 on wlp7s0.IPv4. Dec 26 13:31:16 lizum NetworkManager[784]: <info> (wlp7s0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Dec 26 13:31:16 lizum NetworkManager[784]: <info> Activation (wlp7s0) Stage 5 of 5 (IPv4 Commit) complete. Dec 26 13:31:16 lizum NetworkManager[784]: <info> (wlp7s0): device state change: secondaries -> activated (reason 'none') [90 100 0] Dec 26 13:31:16 lizum NetworkManager[784]: <info> Activation (wlp7s0) successful, device activated. [chuck@Lizum log.50]$ ------------------------------ Chuck
The speed information you requested, using vnstat is: [chuck@Lizum chuck]# vnstat -l -i wlp7s0 Monitoring wlp7s0... (press CTRL-C to stop) rx: 4.70 Mbit/s 401 p/s tx: 360 kbit/s 399 p/s^C wlp7s0 / traffic statistics rx | tx --------------------------------------+------------------ bytes 15.16 MiB | 632 KiB --------------------------------------+------------------ max 5.20 Mbit/s | 360 kbit/s average 3.88 Mbit/s | 158.00 kbit/s min 1.98 Mbit/s | 104 kbit/s --------------------------------------+------------------ packets 10634 | 6671 --------------------------------------+------------------ max 443 p/s | 399 p/s average 332 p/s | 208 p/s min 177 p/s | 156 p/s --------------------------------------+------------------ time 32 seconds [chuck@Lizum chuck]#
Hi Chuck, no worries, I was just making sure we were 100% on the same page ;) So to recap: - We still have the 2.4Ghz vs 5Ghz issue Can you post here the output of 'iwlist scan' please? - Adding nohwcrypt=1 to the module's parameters brought the throughput from a few KB/sec to ~1.5Mbit/s - Also setting the power save functionality to off brought it up to ~4Mbit/s Is the above roughly correct? There were some changes in the TCP stack for bufferbloat which interacted badly with certain drivers and made performance suffer. This could be an explanation for the fact you did not see this issue with previous Fedora versions. I'll need to dig up the whole story on this. Btw. I recommend you do the performance tests with an ftp client or with specialized tools (like iperf or netperf). In my experience nautilus is not as performant due to GIO and is not a good candidate for baselining network performance. regards, Michele
Michele, No problem. Just do as my coworkers do, throw something at me and bean me in the head :-) iwlist scan yields: --------------------------------------------- [chuck@Lizum log]# iwlist scan p2p1 Interface doesn't support scanning. wlp7s0 Scan completed : Cell 01 - Address: 44:94:FC:E5:2B:50 Channel:1 Frequency:2.412 GHz (Channel 1) Quality=68/70 Signal level=-42 dBm Encryption key:on ESSID:"HoheMunde" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000012df27b731 Extra: Last beacon: 7392ms ago IE: Unknown: 0009486F68654D756E6465 IE: Unknown: 010882848B962430486C IE: Unknown: 03010B IE: Unknown: 2A0103 IE: Unknown: 2F0103 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFE181BFFFF000001000000000000000000000000000000000000 IE: Unknown: 3D160B071700000000000000000000000000000000000000 IE: Unknown: 7F080000000000000040 IE: Unknown: DD7A0050F204104A0001101044000102103B00010310470010BDF14ABF0C74A98679597463A2473C51102100074E65746765617210230005443632303010240005443632303010420004313233341054000800060050F20400011011000964736C64657669636510080002200C103C0001031049000600372A000120 IE: Unknown: DD090010180203000C0000 IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 lo Interface doesn't support scanning. [chuck@Lizum log]# ----------------------------------------- That confirms it is only seeing the 2.4G SSID and not the 5G SSID (HoheMundeG5) ? Chuck
Michele, I turned everything in the house back on in case is important. Here is what it shows. Chuck [chuck@Lizum log]# iwlist scan p2p1 Interface doesn't support scanning. wlp7s0 Scan completed : Cell 01 - Address: 44:94:FC:E5:2B:50 Channel:1 Frequency:2.412 GHz (Channel 1) Quality=69/70 Signal level=-41 dBm Encryption key:on ESSID:"HoheMunde" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=000000000098afa9 Extra: Last beacon: 389707ms ago IE: Unknown: 0009486F68654D756E6465 IE: Unknown: 010882848B962430486C IE: Unknown: 030108 IE: Unknown: 2A0103 IE: Unknown: 2F0103 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFE181BFFFF000001000000000000000000000000000000000000 IE: Unknown: 3D1608071300000000000000000000000000000000000000 IE: Unknown: 7F080000000000000040 IE: Unknown: DD7A0050F204104A0001101044000102103B00010310470010BDF14ABF0C74A98679597463A2473C51102100074E65746765617210230005443632303010240005443632303010420004313233341054000800060050F20400011011000964736C64657669636510080002200C103C0001031049000600372A000120 IE: Unknown: DD090010180200000C0000 IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 Cell 02 - Address: 44:94:FC:E5:2B:50 Channel:1 Frequency:2.412 GHz (Channel 1) Quality=60/70 Signal level=-50 dBm Encryption key:on ESSID:"" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=0000000017d72185 Extra: Last beacon: 191ms ago IE: Unknown: 0009000000000000000000 IE: Unknown: 010882848B962430486C IE: Unknown: 030108 IE: Unknown: 050400010000 IE: Unknown: 2A0103 IE: Unknown: 2F0103 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFE181BFFFF000001000000000000000000000000000000000000 IE: Unknown: 3D1608071700000000000000000000000000000000000000 IE: Unknown: 7F080000000000000040 IE: Unknown: DD310050F204104A000110104400010210470010BDF14ABF0C74A98679597463A2473C51103C0001031049000600372A000120 IE: Unknown: DD090010180203000C0000 IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 Cell 03 - Address: 72:94:FC:E5:2B:51 Channel:1 Frequency:2.412 GHz (Channel 1) Quality=60/70 Signal level=-50 dBm Encryption key:on ESSID:"" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=0000000017d72a7b Extra: Last beacon: 189ms ago IE: Unknown: 00080000000000000000 IE: Unknown: 010882848B962430486C IE: Unknown: 030108 IE: Unknown: 050400010000 IE: Unknown: 2A0103 IE: Unknown: 2F0103 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFE181BFFFF000001000000000000000000000000000000000000 IE: Unknown: 3D1608071700000000000000000000000000000000000000 IE: Unknown: 7F080000000000000040 IE: Unknown: DD090010180200000C0000 IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 Cell 04 - Address: B8:3E:59:AF:81:99 Channel:1 Frequency:2.412 GHz (Channel 1) Quality=25/70 Signal level=-85 dBm Encryption key:on ESSID:"DIRECT-roku-350" Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=00000022f157d000 Extra: Last beacon: 256ms ago IE: Unknown: 000F4449524543542D726F6B752D333530 IE: Unknown: 01088C129824B048606C IE: Unknown: 030108 IE: Unknown: 050400030000 IE: Unknown: 0706513220010B1E IE: Unknown: 200100 IE: Unknown: 23021200 IE: Unknown: 2A0102 IE: Unknown: 2F0102 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: 2D1A7C181AFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1608001300000000000000000000000000000000000000 IE: Unknown: DD090010180201102C0000 IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 IE: Unknown: DD050050F20500 IE: Unknown: DD370050F204104A00011010440001021049000600372A0001201054000800060050F20400011011000F4449524543542D726F6B752D333530 IE: Unknown: DD12506F9A090202002709030600B83E59AF8198 [chuck@Lizum log]#
Hi Chuck, so the patch I had in mind has already made it in since 3.12.4: * f4a5ec1 - (2013-12-08 07:29:12 -0800) tcp: tsq: restore minimal amount of queueing <Eric Dumazet> You are testing via 3.12.5 so that does not apply here. I'd give 3.12.6 also a shot as there are some fixes that could be relevant: * 7f79e50 - (2013-12-20 07:48:58 -0800) ath9k: fix duration calculation for non-aggregated packets <Felix Fietkau> * 1c8eac0 - (2013-12-20 07:48:58 -0800) ath9k: Fix XLNA bias strength <Sujith Manoharan> * 4edfe34 - (2013-12-20 07:48:58 -0800) ath9k: Fix QuickDrop usage <Sujith Manoharan> * ec30326 - (2013-10-07 13:34:43 -0400) ath9k: fix tx queue scheduling after channel changes <Felix Fietkau> If that still brings no improvements, I'd give 3.13-rc a shot, just to see if things have been fixed there. I'm out of ideas after that :/ Michele
Michele, We have one very stubborn adapter on our hands. I downloaded the rpms from koji and installed them (kernel, kernel-modules-extra, and kernel-headers to make DKMS happy). I enabled the adapter, watched it connect to the 2.4 Ghz net. It still refused to find the 5 Ghz network. The reported speed for 2.4Ghz '300n' in NetworkManager was 120 Mbps. I ran with it and the wired adapter on for a few minutes to give it settling time (something it seems to need). When I disabled the wired adapter ALL lan traffic to local hosts via direct ip plus simple DNS host resolution through the router, failed. Even a simple 'df' (which has to nfs mounts listed) failed to display anything. I enabled the wired adapter, expecting it to return, but it didn't. Either the resolver had gone into very long timeouts already or something wasn't right. I removed 3.12.6 and rebooted. Normal operation restored. I will wait trying 3.13-rc until you've had time to ponder. Chuck
The AR9485 card that you have is 2.4 Ghz only - it is not a dual-band card and doesn't support 5 Ghz. Please remove the "nohwcrypt" option: http://wireless.kernel.org/en/users/Drivers/ath9k/bugs#Common_Misconceptions Can you attach the output of "sudo lspci -vv" ? Also, 3.12.6 is the latest stable release, can you try it ? (http://koji.fedoraproject.org/koji/packageinfo?packageID=8)
I am running 3.12.6 as it arrived yesterday in the updates. For confirmation, I have 3.12.6-200.fc19.x86_64 installed and running as the default kernel. I have completely disabled the wireless in 3.12.6 as it interferes with ALL dnslookup activity (p2p1 or wlp7s0) (dns lookup failures). 3.12.6 is less compatible with this adapter than 3.12.5 in that regard. Here is the lspci -vv you requested. [chuck@Lizum ~.4]$ sudo lspci -vv 00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=06, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: d0000000-d1ffffff Prefetchable memory behind bridge: 00000000b0000000-00000000cfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [88] Subsystem: Sony Corporation Device 9097 Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: feeff00c Data: 4171 Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <8us ClockPM- Surprise- LLActRep- BwNot+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [140 v1] Root Complex Link Desc: PortNumber=02 ComponentID=01 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed19000 Capabilities: [d94 v1] #19 Kernel driver in use: pcieport 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) (prog-if 30 [XHCI]) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 42 Region 0: Memory at d2300000 (64-bit, non-prefetchable) [size=64K] Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+ Address: 00000000fee0c00c Data: 41c1 Kernel driver in use: xhci_hcd 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 45 Region 0: Memory at d2314000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000feeff00c Data: 4142 Kernel driver in use: mei_me 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at d2319000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP+ Kernel driver in use: ehci-pci 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 43 Region 0: Memory at d2310000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000feeff00c Data: 41e1 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22 Status: NegoPending- InProgress- Capabilities: [130 v1] Root Complex Link Desc: PortNumber=0f ComponentID=00 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed1c000 Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 Memory behind bridge: d2200000-d22fffff Prefetchable memory behind bridge: 00000000d2500000-00000000d25fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #0, PowerLimit 10.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Sony Corporation Device 9097 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 Memory behind bridge: d2100000-d21fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #1, PowerLimit 10.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Sony Corporation Device 9097 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1c.2 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0e, subordinate=0e, sec-latency=0 I/O behind bridge: 00002000-00002fff Prefetchable memory behind bridge: 00000000d2000000-00000000d20fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #2, PowerLimit 10.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Sony Corporation Device 9097 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at d2318000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ehci-pci 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) Subsystem: Sony Corporation Device 9097 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel driver in use: lpc_ich 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Sony Corporation Device 9097 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 41 Region 0: I/O ports at 4048 [size=8] Region 1: I/O ports at 4054 [size=4] Region 2: I/O ports at 4040 [size=8] Region 3: I/O ports at 4050 [size=4] Region 4: I/O ports at 4020 [size=32] Region 5: Memory at d2317000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0c00c Data: 41b1 Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004 Capabilities: [b0] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) Subsystem: Sony Corporation Device 9097 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 19 Region 0: Memory at d2315000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 4000 [size=32] 01:00.0 VGA compatible controller: NVIDIA Corporation GF108M [GeForce GT 620M] (rev a1) (prog-if 00 [VGA controller]) Subsystem: Sony Corporation Device 9097 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at b0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at c0000000 (64-bit, prefetchable) [size=32M] Region 5: I/O ports at 3000 [size=128] Expansion ROM at c2000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <4us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [128 v1] Power Budgeting <?> Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau 01:00.1 Audio device: NVIDIA Corporation GF108 High Definition Audio Controller (rev a1) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <4us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM L1 Enabled; RCB 128 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Kernel driver in use: snd_hda_intel 07:00.0 Network controller: Qualcomm Atheros AR9485 Wireless Network Adapter (rev 01) Subsystem: Foxconn International, Inc. Device e044 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at d2200000 (64-bit, non-prefetchable) [size=512K] Expansion ROM at d2500000 [disabled] [size=64K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/4 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Kernel driver in use: ath9k 08:00.0 SD Host controller: Ricoh Co Ltd MMC/SD Host Controller (rev 09) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at d2102000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [78] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- Capabilities: [80] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [800 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Kernel driver in use: sdhci-pci 08:00.1 System peripheral: Ricoh Co Ltd Device e232 (rev 06) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 11 Region 0: Memory at d2101000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [78] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- Capabilities: [80] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- 08:00.3 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 PCIe IEEE 1394 Controller (rev 05) (prog-if 10 [OHCI]) Subsystem: Sony Corporation Device 9097 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin D routed to IRQ 16 Region 0: Memory at d2100000 (32-bit, non-prefetchable) [size=2K] Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [78] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME+ Capabilities: [80] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Kernel driver in use: firewire_ohci 0e:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07) Subsystem: Sony Corporation Device 9097 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 44 Region 0: I/O ports at 2000 [size=256] Region 2: Memory at d2004000 (64-bit, prefetchable) [size=4K] Region 4: Memory at d2000000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee2000c Data: 4122 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data No end tag found Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Kernel driver in use: r8169 [chuck@Lizum ~.5]$
*********** MASS BUG UPDATE ************** We apologize for the inconvenience. There is a large number of bugs to go through and several of them have gone stale. Due to this, we are doing a mass bug update across all of the Fedora 19 kernel bugs. Fedora 19 has now been rebased to 3.13.5-100.fc19. Please test this kernel update and let us know if you issue has been resolved or if it is still present with the newer kernel. If you experience different issues, please open a new bug report for those.
*********** MASS BUG UPDATE ************** This bug is being closed with INSUFFICIENT_DATA as there has not been a response in 4 weeks. If you are still experiencing this issue, please reopen and attach the relevant data from the latest kernel you are running and any data that might have been requested previously.