Hide Forgot
Description of problem: When trying to play a wave file using aplay on FC4test3 I get the following warning/error. This isn't a bogus warning/error - the wave truely doesn't play at the correct sample rate. [dave@maggie tmp]$ file test.wav test.wav: RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, stereo 44100 Hz [dave@maggie tmp]$ aplay test.wav Playing WAVE 'test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo Warning: rate is not accurate (requested = 44100Hz, got = 48000Hz) please, try the plug plugin (-Dplug:default) arecord is also exhibiting the same problem so I'm guessing there's something wrong w/ the alsa config, but I haven't yet been able to figure it out. [dave@maggie tmp]$ arecord -f cd foo.wav Recording WAVE 'foo.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo Warning: rate is not accurate (requested = 44100Hz, got = 48000Hz) please, try the plug plugin (-Dplug:default) Aborted by signal Interrupt... And when I try what's suggested in the warning message it records at 8bit/8KHz: dave@maggie tmp]$ arecord -Dplug:default foo.wav Recording WAVE 'foo.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono Aborted by signal Interrupt... [dave@maggie tmp]$ aplay foo.wav Playing WAVE 'foo.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono aplay: set_params:857: Sample format non available Version-Release number of selected component (if applicable): alsa-utils-1.0.9rc2-1 How reproducible: Every time Steps to Reproduce: 1. use aplay to play wave file 2. 3. Actual results: played at wrong sample rate, warning/error message Expected results: played correctly Additional info: [dave@maggie ~]$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I440MX [Intel 440MX], device 0: Intel ICH [Intel 440MX] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: Modem [Intel 440MX Modem], device 0: Intel ICH - Modem [Intel 440MX Modem - Modem] Subdevices: 1/1 Subdevice #0: subdevice #0 [dave@maggie ~]$ aplay -L PCM list: hw { @args.0 CARD @args.1 DEV @args.2 SUBDEV @args.CARD { type string default { @func getenv vars { 0 ALSA_PCM_CARD 1 ALSA_CARD } default { @func refer name 'defaults.pcm.card' } } } @args.DEV { type integer default { @func igetenv vars { 0 ALSA_PCM_DEVICE } default { @func refer name 'defaults.pcm.device' } } } @args.SUBDEV { type integer default { @func refer name 'defaults.pcm.subdevice' } } type hw card $CARD device $DEV subdevice $SUBDEV } plughw { @args.0 CARD @args.1 DEV @args.2 SUBDEV @args.CARD { type string default { @func getenv vars { 0 ALSA_PCM_CARD 1 ALSA_CARD } default { @func refer name 'defaults.pcm.card' } } } @args.DEV { type integer default { @func igetenv vars { 0 ALSA_PCM_DEVICE } default { @func refer name 'defaults.pcm.device' } } } @args.SUBDEV { type integer default { @func refer name 'defaults.pcm.subdevice' } } type plug slave.pcm { type hw card $CARD device $DEV subdevice $SUBDEV } } plug { @args.0 SLAVE @args.SLAVE { type string } type plug slave.pcm $SLAVE } shm { @args.0 SOCKET @args.1 PCM @args.SOCKET { type string } @args.PCM { type string } type shm server $SOCKET pcm $PCM } tee { @args.0 SLAVE @args.1 FILE @args.2 FORMAT @args.SLAVE { type string } @args.FILE { type string } @args.FORMAT { type string default raw } type file slave.pcm $SLAVE file $FILE format $FORMAT } file { @args.0 FILE @args.1 FORMAT @args.FILE { type string } @args.FORMAT { type string default raw } type file slave.pcm null file $FILE format $FORMAT } null { type null } cards 'cards.pcm' front 'cards.pcm.front' rear 'cards.pcm.rear' center_lfe 'cards.pcm.center_lfe' side 'cards.pcm.side' surround40 'cards.pcm.surround40' surround41 'cards.pcm.surround41' surround50 'cards.pcm.surround50' surround51 'cards.pcm.surround51' surround71 'cards.pcm.surround71' iec958 'cards.pcm.iec958' spdif 'cards.pcm.iec958' modem 'cards.pcm.modem' dmix 'cards.pcm.dmix' dsnoop 'cards.pcm.dsnoop' default { type hw card 0 } [dave@maggie ~]$lsmod Module Size Used by nfs 219049 0 lockd 63209 1 nfs tun 11457 0 parport_pc 28933 0 lp 13001 0 parport 40585 2 parport_pc,lp autofs4 29253 1 rfcomm 42333 0 l2cap 30661 5 rfcomm bluetooth 56133 4 rfcomm,l2cap sunrpc 167813 3 nfs,lockd orinoco_cs 10825 1 orinoco 53965 1 orinoco_cs hermes 7233 2 orinoco_cs,orinoco pcmcia 28897 5 orinoco_cs dm_mod 58101 0 video 15941 0 button 6609 0 battery 9413 0 ac 4805 0 md5 4033 1 ipv6 267969 10 pcspkr 4253 0 yenta_socket 21449 3 rsrc_nonstatic 12737 1 yenta_socket pcmcia_core 50909 4 orinoco_cs,pcmcia,yenta_socket,rsrc_nonstatic uhci_hcd 34641 0 snd_intel8x0m 19589 0 i2c_piix4 8657 0 i2c_core 21569 1 i2c_piix4 snd_intel8x0 34689 2 snd_ac97_codec 75961 2 snd_intel8x0m,snd_intel8x0 snd_seq_dummy 3653 0 snd_seq_oss 37057 0 snd_seq_midi_event 9153 1 snd_seq_oss snd_seq 62289 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 8781 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 51185 0 snd_mixer_oss 17857 2 snd_pcm_oss snd_pcm 100169 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_timer 33605 2 snd_seq,snd_pcm snd 57157 12 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer soundcore 10913 2 snd snd_page_alloc 9669 3 snd_intel8x0m,snd_intel8x0,snd_pcm e100 47297 0 mii 5441 1 e100 ext3 132553 3 jbd 86233 1 ext3 [dave@maggie ~]$ lspci 00:00.0 Host bridge: Intel Corporation 82440MX Host Bridge (rev 01) 00:00.1 Multimedia audio controller: Intel Corporation 82440MX AC'97 Audio Controller 00:00.2 Modem: Intel Corporation 82440MX AC'97 Modem Controller 00:07.0 Bridge: Intel Corporation 82440MX ISA Bridge (rev 01) 00:07.1 IDE interface: Intel Corporation 82440MX EIDE Controller 00:07.2 USB Controller: Intel Corporation 82440MX USB Universal Host Controller 00:07.3 Bridge: Intel Corporation 82440MX Power Management Controller 00:12.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 09) 00:13.0 CardBus bridge: O2 Micro, Inc. OZ6933/711E1 CardBus/SmartCardBus Controller (rev 02) 00:13.1 CardBus bridge: O2 Micro, Inc. OZ6933/711E1 CardBus/SmartCardBus Controller (rev 02) 00:14.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M (rev 64) [dave@maggie ~]$ sudo lspci -vv 00:00.0 Host bridge: Intel Corporation 82440MX Host Bridge (rev 01) Subsystem: Fujitsu Limited.: Unknown device 107f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 00:00.1 Multimedia audio controller: Intel Corporation 82440MX AC'97 Audio Controller Subsystem: Fujitsu Limited.: Unknown device 10d0 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 9 Region 0: I/O ports at 1000 [size=256] Region 1: I/O ports at 1400 [size=64] 00:00.2 Modem: Intel Corporation 82440MX AC'97 Modem Controller (prog-if 00 [Generic]) Subsystem: Fujitsu Limited.: Unknown device 10d1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 9 Region 0: I/O ports at 2000 [size=256] Region 1: I/O ports at 1800 [size=128] 00:07.0 Bridge: Intel Corporation 82440MX ISA Bridge (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:07.1 IDE interface: Intel Corporation 82440MX EIDE Controller (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at 14a0 [size=16] 00:07.2 USB Controller: Intel Corporation 82440MX USB Universal Host Controller (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin D routed to IRQ 15 Region 4: I/O ports at 1480 [size=32] 00:07.3 Bridge: Intel Corporation 82440MX Power Management Controller Control: I/O+ Mem+ BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:12.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 09) Subsystem: Fujitsu Limited.: Unknown device 1070 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min, 14000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 9 Region 0: Memory at fc020000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 1440 [size=64] Region 2: Memory at fc000000 (32-bit, non-prefetchable) [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 00:13.0 CardBus bridge: O2 Micro, Inc. OZ6933/711E1 CardBus/SmartCardBus Controller (rev 02) Subsystem: Fujitsu Limited.: Unknown device 10e6 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin A routed to IRQ 9 Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=01, subordinate=04, sec-latency=176 Memory window 0: 10400000-107ff000 (prefetchable) Memory window 1: 10800000-10bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00:13.1 CardBus bridge: O2 Micro, Inc. OZ6933/711E1 CardBus/SmartCardBus Controller (rev 02) Subsystem: Fujitsu Limited.: Unknown device 10e6 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin B routed to IRQ 9 Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=05, subordinate=08, sec-latency=176 Memory window 0: 10c00000-10fff000 (prefetchable) Memory window 1: 11000000-113ff000 I/O window 0: 00004800-000048ff I/O window 1: 00004c00-00004cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00:14.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M (rev 64) (prog-if 00 [VGA]) Subsystem: Fujitsu Limited.: Unknown device 1103 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min), Cache Line Size 08 Interrupt: pin A routed to IRQ 9 Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at 2400 [size=256] Region 2: Memory at fc021000 (32-bit, non-prefetchable) [size=4K] Capabilities: [5c] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- [dave@maggie ~]$
correction, when I pass the suggested plugin (-Dplug:default) and the correct format (-f cd) it plays correctly: [dave@maggie tmp]$ aplay -Dplug:default -f cd test.wav Playing WAVE 'test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo Aborted by signal Interrupt... [dave@maggie tmp]$ Not sure why this is needing to be specified now ... didn't need to under FC3.
It will work properly if you remove /etc/asound.conf file. I have to fix system-config-soundcard, it writes only simple configuration now.
Martin - you're exactly right, removing the /etc/asound.conf did the trick here. Looks like the config generated by S-C-S was quite close to being correct. Just needed to replace "!default" with "intel8x0" globally. Thanks!
The problem is here: default { type hw card 0 } ALSA has his own configuration for Intel ICH, but S-C-S bypasses it with hw device.
So I guess this should turn into a S-C-S bug ...