Description of problem:The installed sound card is the Creative Labs Sound Blaster 128 (CT4750) with the Creative Labs chip CT5880 DCQ. The onboard sound has been disabled and is so shown in PulseAudio Volume Control. The alsamixer shows "HD Audio Generic", although another card is listed as a choice; Ensoniq AudioPCI. But even after selecting that one, which has at least worked, and after saving the setup with "alsactl store", the card selection will not take and I am left with no sound. According to the ALSA Matrix of cards, I believe I should be using the emu10k1 module, but I'm not sure. (The table is skewed.) Version-Release number of selected component (if applicable): How reproducible: Steps to Reproduce: 1. 2. 3. Actual results: Expected results: Additional info: lsmod shows: Module Size Used by fuse 77970 3 lockd 93540 0 sunrpc 256499 1 lockd ip6t_REJECT 12939 2 nf_conntrack_ipv6 18782 7 nf_defrag_ipv6 18205 1 nf_conntrack_ipv6 ip6table_filter 12815 1 nf_conntrack_ipv4 14808 6 nf_defrag_ipv4 12673 1 nf_conntrack_ipv4 ip6_tables 26808 1 ip6table_filter xt_state 12578 13 nf_conntrack 84243 3 xt_state,nf_conntrack_ipv4,nf_conntrack_ipv6 binfmt_misc 17463 1 snd_ens1371 25378 2 gameport 15042 1 snd_ens1371 snd_rawmidi 29531 1 snd_ens1371 snd_ac97_codec 133373 1 snd_ens1371 ac97_bus 12718 1 snd_ac97_codec snd_hda_codec_hdmi 36748 1 snd_hda_intel 43715 2 snd_hda_codec 132514 2 snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 17650 1 snd_hda_codec snd_seq 64877 0 snd_seq_device 14136 2 snd_seq,snd_rawmidi serio_raw 13375 0 snd_pcm 102100 5 snd_ac97_codec,snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_ens1371 edac_core 56455 0 k8temp 12978 0 edac_mce_amd 22634 0 forcedeth 67508 0 snd_page_alloc 18268 2 snd_pcm,snd_hda_intel snd_timer 28690 2 snd_pcm,snd_seq snd 79379 19 snd_ac97_codec,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_ens1371,snd_seq_device soundcore 14491 1 snd i2c_nforce2 13173 0 asus_atk0110 18657 0 ata_generic 12910 0 pata_acpi 13038 0 sata_nv 31841 4 pata_amd 14129 0 radeon 941765 2 i2c_algo_bit 13257 1 radeon drm_kms_helper 46708 1 radeon ttm 79629 1 radeon drm 264680 4 ttm,drm_kms_helper,radeon i2c_core 38353 5 drm,drm_kms_helper,i2c_algo_bit,radeon,i2c_nforce2 I also notice that aplay will not work.
upload=true&script=true&cardinfo= !!################################ !!ALSA Information Script v 0.4.61 !!################################ !!Script ran on: Fri Mar 29 19:33:14 UTC 2013 !!Linux Distribution !!------------------ Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) NAME=Fedora ID=fedora PRETTY_NAME="Fedora 17 (Beefy Miracle)" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) !!DMI Information !!--------------- Manufacturer: System manufacturer Product Name: System Product Name Product Version: System Version Firmware Version: ASUS A8N-SLI SE ACPI BIOS Revision 0502 !!Kernel Information !!------------------ Kernel release: 3.8.3-103.fc17.x86_64 Operating System: GNU/Linux Architecture: x86_64 Processor: x86_64 SMP Enabled: Yes !!ALSA Version !!------------ Driver version: k3.8.3-103.fc17.x86_64 Library version: 1.0.26 Utilities version: 1.0.26 !!Loaded ALSA modules !!------------------- snd_hda_intel snd_ens1371 !!Sound Servers on this system !!---------------------------- Pulseaudio: Installed - Yes (/usr/bin/pulseaudio) Running - Yes aRts: Installed - Yes (/usr/bin/artsd) Running - No Jack: Installed - Yes (/usr/bin/jackd) Running - No !!Soundcards recognised by ALSA !!----------------------------- 0 [Generic ]: HDA-Intel - HD-Audio Generic HD-Audio Generic at 0xd1020000 irq 45 1 [AudioPCI ]: ENS1371 - Ensoniq AudioPCI Ensoniq AudioPCI ENS1371 at 0xb000, irq 16 !!PCI Soundcards installed in the system !!-------------------------------------- 01:00.1 Audio device: ATI Technologies Inc Redwood HDMI Audio [Radeon HD 5600 Series] 05:06.0 Multimedia audio controller: Ensoniq 5880B [AudioPCI] (rev 02) !!Advanced information - PCI Vendor/Device/Subsystem ID's !!------------------------------------------------------- 01:00.1 0403: 1002:aa60 Subsystem: 1682:aa60 -- 05:06.0 0401: 1274:5880 (rev 02) Subsystem: 1274:8001 !!Loaded sound module options !!--------------------------- !!Module: snd_hda_intel align_buffer_size : -1 bdl_pos_adj : 32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 beep_mode : N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y enable_msi : -1 id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null) index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 jackpoll_ms : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null) patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null) position_fix : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 power_save : 0 power_save_controller : Y probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 single_cmd : N snoop : Y !!Module: snd_ens1371 enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null) index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 joystick_port : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 lineio : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 spdif : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 !!HDA-Intel Codec information !!--------------------------- --startcollapse-- Codec: ATI R6xx HDMI Address: 0 AFG Function Id: 0x1 (unsol 0) Vendor Id: 0x1002aa01 Subsystem Id: 0x00aa0100 Revision Id: 0x100200 No Modem Function Group found Default PCM: rates [0x70]: 32000 44100 48000 bits [0x2]: 16 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A GPIO: io=0, o=0, i=0, unsolicited=0, wake=0 Node 0x02 [Audio Output] wcaps 0x201: Stereo Digital Converter: stream=1, channel=0 Digital: Enabled Digital category: 0x0 IEC Coding Type: 0x0 Node 0x03 [Pin Complex] wcaps 0x400381: Stereo Digital Control: name="HDMI/DP,pcm=3 Jack", index=0, device=0 Control: name="IEC958 Playback Con Mask", index=0, device=0 Control: name="IEC958 Playback Pro Mask", index=0, device=0 Control: name="IEC958 Playback Default", index=0, device=0 Control: name="IEC958 Playback Switch", index=0, device=0 Control: name="ELD", index=0, device=3 Pincap 0x00000094: OUT Detect HDMI Pin Default 0x18560010: [Jack] Digital Out at Int HDMI Conn = Digital, Color = Unknown DefAssociation = 0x1, Sequence = 0x0 Pin-ctls: 0x40: OUT Unsolicited: tag=01, enabled=1 Connection: 1 0x02 --endcollapse-- !!AC97 Codec information !!---------------------- --startcollapse-- 0-0/0: SigmaTel STAC9708,11 PCI Subsys Vendor: 0x1274 PCI Subsys Device: 0x8001 Flags: 0 Capabilities : -headphone out- DAC resolution : 18-bit ADC resolution : 18-bit 3D enhancement : SigmaTel 3D Enhancement Current setup Mic gain : +0dB [+0dB] POP path : pre 3D Sim. stereo : off 3D enhancement : off Loudness : off Mono output : MIX Mic select : Mic1 ADC/DAC loopback : off Extended ID : codec=0 rev=0 SDAC DSA=0 Extended status : SDAC 0:00 = 6940 0:02 = 0000 0:04 = 8303 0:06 = 801f 0:08 = 0000 0:0a = 0014 0:0c = 801f 0:0e = 801f 0:10 = 9f1f 0:12 = 0b0b 0:14 = 0303 0:16 = 9f1f 0:18 = 0808 0:1a = 0000 0:1c = 0808 0:1e = 0000 0:20 = 0000 0:22 = 0000 0:24 = 0000 0:26 = 000f 0:28 = 0080 0:2a = 0080 0:2c = 0000 0:2e = 0000 0:30 = 0000 0:32 = 0000 0:34 = 0000 0:36 = 0000 0:38 = 0000 0:3a = 0000 0:3c = 0000 0:3e = 0000 0:40 = 0000 0:42 = 0000 0:44 = 0000 0:46 = 0000 0:48 = 0000 0:4a = 0000 0:4c = 0000 0:4e = 0000 0:50 = 0000 0:52 = 0000 0:54 = 0000 0:56 = 0000 0:58 = 0000 0:5a = 0000 0:5c = 0000 0:5e = 0000 0:60 = 0000 0:62 = 0000 0:64 = 0000 0:66 = 0000 0:68 = 0000 0:6a = 0000 0:6c = 0080 0:6e = 0000 0:70 = 0000 0:72 = 8000 0:74 = 0000 0:76 = 0000 0:78 = 8380 0:7a = 0000 0:7c = 8384 0:7e = 7608 --endcollapse-- !!ALSA Device nodes !!----------------- crw-rw----+ 1 root audio 116, 4 Mar 29 10:04 /dev/snd/controlC0 crw-rw----+ 1 root audio 116, 9 Mar 29 10:04 /dev/snd/controlC1 crw-rw----+ 1 root audio 116, 3 Mar 29 10:04 /dev/snd/hwC0D0 crw-rw----+ 1 root audio 116, 5 Mar 29 10:04 /dev/snd/midiC1D0 crw-rw----+ 1 root audio 116, 2 Mar 29 14:35 /dev/snd/pcmC0D3p crw-rw----+ 1 root audio 116, 8 Mar 29 14:35 /dev/snd/pcmC1D0c crw-rw----+ 1 root audio 116, 7 Mar 29 15:15 /dev/snd/pcmC1D0p crw-rw----+ 1 root audio 116, 6 Mar 29 14:35 /dev/snd/pcmC1D1p crw-rw----+ 1 root audio 116, 1 Mar 29 10:04 /dev/snd/seq crw-rw----+ 1 root audio 116, 33 Mar 29 10:04 /dev/snd/timer /dev/snd/by-path: total 0 drwxr-xr-x 2 root root 80 Mar 29 10:04 . drwxr-xr-x 3 root root 260 Mar 29 10:04 .. lrwxrwxrwx 1 root root 12 Mar 29 10:04 pci-0000:01:00.1 -> ../controlC0 lrwxrwxrwx 1 root root 12 Mar 29 10:04 pci-0000:05:06.0 -> ../controlC1 !!ALSA configuration files !!------------------------ !!System wide config file (/etc/asound.conf) # # Place your global alsa-lib configuration here... # !!Aplay/Arecord output !!-------------------- APLAY **** List of PLAYBACK Hardware Devices **** card 0: Generic [HD-Audio Generic], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: AudioPCI [Ensoniq AudioPCI], device 0: ES1371/1 [ES1371 DAC2/ADC] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: AudioPCI [Ensoniq AudioPCI], device 1: ES1371/2 [ES1371 DAC1] Subdevices: 1/1 Subdevice #0: subdevice #0 ARECORD **** List of CAPTURE Hardware Devices **** card 1: AudioPCI [Ensoniq AudioPCI], device 0: ES1371/1 [ES1371 DAC2/ADC] Subdevices: 1/1 Subdevice #0: subdevice #0 !!Amixer output !!------------- !!-------Mixer controls for card 0 [Generic] Card hw:0 'Generic'/'HD-Audio Generic at 0xd1020000 irq 45' Mixer name : 'ATI R6xx HDMI' Components : 'HDA:1002aa01,00aa0100,00100200' Controls : 7 Simple ctrls : 1 Simple mixer control 'IEC958',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] !!-------Mixer controls for card 1 [AudioPCI] Card hw:1 'AudioPCI'/'Ensoniq AudioPCI ENS1371 at 0xb000, irq 16' Mixer name : 'SigmaTel STAC9708,11' Components : 'AC97a:83847608' Controls : 44 Simple ctrls : 27 Simple mixer control 'Master',0 Capabilities: pvolume pswitch pswitch-joined Playback channels: Front Left - Front Right Limits: Playback 0 - 31 Mono: Front Left: Playback 31 [100%] [0.00dB] [on] Front Right: Playback 31 [100%] [0.00dB] [on] Simple mixer control 'Master Mono',0 Capabilities: pvolume pvolume-joined pswitch pswitch-joined Playback channels: Mono Limits: Playback 0 - 31 Mono: Playback 0 [0%] [-46.50dB] [off] Simple mixer control '3D Control - Switch',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [off] Simple mixer control '3D Control Sigmatel - Depth',0 Capabilities: pvolume pvolume-joined Playback channels: Mono Limits: Playback 0 - 3 Mono: Playback 0 [0%] Simple mixer control '3D Control Sigmatel - Rear Depth',0 Capabilities: pvolume pvolume-joined Playback channels: Mono Limits: Playback 0 - 3 Mono: Playback 0 [0%] Simple mixer control 'PCM',0 Capabilities: pvolume pswitch pswitch-joined Playback channels: Front Left - Front Right Limits: Playback 0 - 31 Mono: Front Left: Playback 23 [74%] [0.00dB] [on] Front Right: Playback 23 [74%] [0.00dB] [on] Simple mixer control 'Surround',0 Capabilities: pvolume pswitch Playback channels: Front Left - Front Right Limits: Playback 0 - 31 Mono: Front Left: Playback 31 [100%] [0.00dB] [on] Front Right: Playback 31 [100%] [0.00dB] [on] Simple mixer control 'Surround Phase Inversion',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [off] Simple mixer control 'Line',0 Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive Capture exclusive group: 0 Playback channels: Front Left - Front Right Capture channels: Front Left - Front Right Limits: Playback 0 - 31 Front Left: Playback 0 [0%] [-34.50dB] [off] Capture [off] Front Right: Playback 0 [0%] [-34.50dB] [off] Capture [off] Simple mixer control 'CD',0 Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive Capture exclusive group: 0 Playback channels: Front Left - Front Right Capture channels: Front Left - Front Right Limits: Playback 0 - 31 Front Left: Playback 20 [65%] [-4.50dB] [on] Capture [off] Front Right: Playback 20 [65%] [-4.50dB] [on] Capture [off] Simple mixer control 'Mic',0 Capabilities: pvolume pvolume-joined pswitch pswitch-joined cswitch cswitch-exclusive Capture exclusive group: 0 Playback channels: Mono Capture channels: Front Left - Front Right Limits: Playback 0 - 31 Mono: Playback 0 [0%] [-34.50dB] [off] Front Left: Capture [on] Front Right: Capture [on] Simple mixer control 'Mic Boost (+20dB)',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [off] Simple mixer control 'Mic Select',0 Capabilities: enum Items: 'Mic1' 'Mic2' Item0: 'Mic1' Simple mixer control 'Video',0 Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive Capture exclusive group: 0 Playback channels: Front Left - Front Right Capture channels: Front Left - Front Right Limits: Playback 0 - 31 Front Left: Playback 28 [90%] [7.50dB] [on] Capture [off] Front Right: Playback 28 [90%] [7.50dB] [on] Capture [off] Simple mixer control 'Phone',0 Capabilities: pvolume pvolume-joined pswitch pswitch-joined cswitch cswitch-exclusive Capture exclusive group: 0 Playback channels: Mono Capture channels: Front Left - Front Right Limits: Playback 0 - 31 Mono: Playback 0 [0%] [-34.50dB] [off] Front Left: Capture [off] Front Right: Capture [off] Simple mixer control 'IEC958',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [off] Simple mixer control 'Beep',0 Capabilities: pvolume pvolume-joined pswitch pswitch-joined Playback channels: Mono Limits: Playback 0 - 15 Mono: Playback 5 [33%] [-30.00dB] [on] Simple mixer control 'Aux',0 Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive Capture exclusive group: 0 Playback channels: Front Left - Front Right Capture channels: Front Left - Front Right Limits: Playback 0 - 31 Front Left: Playback 0 [0%] [-34.50dB] [off] Capture [off] Front Right: Playback 0 [0%] [-34.50dB] [off] Capture [off] Simple mixer control 'Mono Output Select',0 Capabilities: enum Items: 'Mix' 'Mic' Item0: 'Mix' Simple mixer control 'Capture',0 Capabilities: cvolume cswitch cswitch-joined Capture channels: Front Left - Front Right Limits: Capture 0 - 15 Front Left: Capture 8 [53%] [12.00dB] [on] Front Right: Capture 8 [53%] [12.00dB] [on] Simple mixer control 'Mix',0 Capabilities: cswitch cswitch-exclusive Capture exclusive group: 0 Capture channels: Front Left - Front Right Front Left: Capture [off] Front Right: Capture [off] Simple mixer control 'Mix Mono',0 Capabilities: cswitch cswitch-exclusive Capture exclusive group: 0 Capture channels: Front Left - Front Right Front Left: Capture [off] Front Right: Capture [off] Simple mixer control 'AC97 2ch->4ch Copy',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] Simple mixer control 'External Amplifier',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] Simple mixer control 'Sigmatel 4-Speaker Stereo',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [off] Simple mixer control 'Sigmatel Output Bias',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [off] Simple mixer control 'Sigmatel Surround',0 Capabilities: pvolume pswitch pswitch-joined Playback channels: Front Left - Front Right Limits: Playback 0 - 31 Mono: Front Left: Playback 28 [90%] [-4.50dB] [off] Front Right: Playback 28 [90%] [-4.50dB] [off] !!Alsactl output !!-------------- --startcollapse-- state.Generic { control.1 { iface CARD name 'HDMI/DP,pcm=3 Jack' value false comment { access read type BOOLEAN count 1 } } control.2 { iface MIXER name 'IEC958 Playback Con Mask' value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000' comment { access read type IEC958 count 1 } } control.3 { iface MIXER name 'IEC958 Playback Pro Mask' value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000' comment { access read type IEC958 count 1 } } control.4 { iface MIXER name 'IEC958 Playback Default' value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000' comment { access 'read write' type IEC958 count 1 } } control.5 { iface MIXER name 'IEC958 Playback Switch' value true comment { access 'read write' type BOOLEAN count 1 } } control.6 { iface PCM device 3 name ELD value '' comment { access 'read volatile' type BYTES count 0 } } control.7 { iface PCM device 3 name 'Playback Channel Map' value.0 0 value.1 0 comment { access 'read write' type INTEGER count 2 range '0 - 36' } } } state.AudioPCI { control.1 { iface MIXER name 'Master Playback Switch' value true comment { access 'read write' type BOOLEAN count 1 } } control.2 { iface MIXER name 'Master Playback Volume' value.0 31 value.1 31 comment { access 'read write' type INTEGER count 2 range '0 - 31' dbmin -4650 dbmax 0 dbvalue.0 0 dbvalue.1 0 } } control.3 { iface MIXER name 'Surround Playback Switch' value.0 true value.1 true comment { access 'read write' type BOOLEAN count 2 } } control.4 { iface MIXER name 'Surround Playback Volume' value.0 31 value.1 31 comment { access 'read write' type INTEGER count 2 range '0 - 31' dbmin -4650 dbmax 0 dbvalue.0 0 dbvalue.1 0 } } control.5 { iface MIXER name 'Sigmatel Surround Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.6 { iface MIXER name 'Sigmatel Surround Playback Volume' value.0 28 value.1 28 comment { access 'read write' type INTEGER count 2 range '0 - 31' dbmin -4650 dbmax 0 dbvalue.0 -450 dbvalue.1 -450 } } control.7 { iface MIXER name 'Master Mono Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.8 { iface MIXER name 'Master Mono Playback Volume' value 0 comment { access 'read write' type INTEGER count 1 range '0 - 31' dbmin -4650 dbmax 0 dbvalue.0 -4650 } } control.9 { iface MIXER name 'Beep Playback Switch' value true comment { access 'read write' type BOOLEAN count 1 } } control.10 { iface MIXER name 'Beep Playback Volume' value 5 comment { access 'read write' type INTEGER count 1 range '0 - 15' dbmin -4500 dbmax 0 dbvalue.0 -3000 } } control.11 { iface MIXER name 'Phone Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.12 { iface MIXER name 'Phone Playback Volume' value 0 comment { access 'read write' type INTEGER count 1 range '0 - 31' dbmin -3450 dbmax 1200 dbvalue.0 -3450 } } control.13 { iface MIXER name 'Mic Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.14 { iface MIXER name 'Mic Playback Volume' value 0 comment { access 'read write' type INTEGER count 1 range '0 - 31' dbmin -3450 dbmax 1200 dbvalue.0 -3450 } } control.15 { iface MIXER name 'Mic Boost (+20dB)' value false comment { access 'read write' type BOOLEAN count 1 } } control.16 { iface MIXER name 'Line Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.17 { iface MIXER name 'Line Playback Volume' value.0 0 value.1 0 comment { access 'read write' type INTEGER count 2 range '0 - 31' dbmin -3450 dbmax 1200 dbvalue.0 -3450 dbvalue.1 -3450 } } control.18 { iface MIXER name 'CD Playback Switch' value true comment { access 'read write' type BOOLEAN count 1 } } control.19 { iface MIXER name 'CD Playback Volume' value.0 20 value.1 20 comment { access 'read write' type INTEGER count 2 range '0 - 31' dbmin -3450 dbmax 1200 dbvalue.0 -450 dbvalue.1 -450 } } control.20 { iface MIXER name 'Video Playback Switch' value true comment { access 'read write' type BOOLEAN count 1 } } control.21 { iface MIXER name 'Video Playback Volume' value.0 28 value.1 28 comment { access 'read write' type INTEGER count 2 range '0 - 31' dbmin -3450 dbmax 1200 dbvalue.0 750 dbvalue.1 750 } } control.22 { iface MIXER name 'Aux Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.23 { iface MIXER name 'Aux Playback Volume' value.0 0 value.1 0 comment { access 'read write' type INTEGER count 2 range '0 - 31' dbmin -3450 dbmax 1200 dbvalue.0 -3450 dbvalue.1 -3450 } } control.24 { iface MIXER name 'PCM Playback Switch' value true comment { access 'read write' type BOOLEAN count 1 } } control.25 { iface MIXER name 'PCM Playback Volume' value.0 23 value.1 23 comment { access 'read write' type INTEGER count 2 range '0 - 31' dbmin -3450 dbmax 1200 dbvalue.0 0 dbvalue.1 0 } } control.26 { iface MIXER name 'Capture Source' value.0 Mic value.1 Mic comment { access 'read write' type ENUMERATED count 2 item.0 Mic item.1 CD item.2 Video item.3 Aux item.4 Line item.5 Mix item.6 'Mix Mono' item.7 Phone } } control.27 { iface MIXER name 'Capture Switch' value true comment { access 'read write' type BOOLEAN count 1 } } control.28 { iface MIXER name 'Capture Volume' value.0 8 value.1 8 comment { access 'read write' type INTEGER count 2 range '0 - 15' dbmin 0 dbmax 2250 dbvalue.0 1200 dbvalue.1 1200 } } control.30 { iface MIXER name '3D Control - Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.31 { iface MIXER name 'Mono Output Select' value Mix comment { access 'read write' type ENUMERATED count 1 item.0 Mix item.1 Mic } } control.32 { iface MIXER name 'Mic Select' value Mic1 comment { access 'read write' type ENUMERATED count 1 item.0 Mic1 item.1 Mic2 } } control.33 { iface MIXER name '3D Control Sigmatel - Depth' value 0 comment { access 'read write' type INTEGER count 1 range '0 - 3' } } control.34 { iface MIXER name '3D Control Sigmatel - Rear Depth' value 0 comment { access 'read write' type INTEGER count 1 range '0 - 3' } } control.35 { iface MIXER name 'Sigmatel Output Bias Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.36 { iface MIXER name 'Sigmatel 4-Speaker Stereo Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.37 { iface MIXER name 'Surround Phase Inversion Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.38 { iface MIXER name 'External Amplifier' value true comment { access 'read write' type BOOLEAN count 1 } } control.39 { iface MIXER name 'IEC958 Playback Switch' value false comment { access 'read write' type BOOLEAN count 1 } } control.40 { iface PCM name 'IEC958 Playback Default' value '0082000200000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000' comment { access 'read write' type IEC958 count 1 } } control.41 { iface PCM name 'IEC958 Playback Mask' value ffffffff00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 comment { access read type IEC958 count 1 } } control.42 { iface PCM name 'IEC958 Playback PCM Stream' value '0082000200000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000' comment { access 'read write' type IEC958 count 1 } } control.43 { iface MIXER name 'AC97 2ch->4ch Copy Switch' value true comment { access 'read write' type BOOLEAN count 1 } } control.44 { iface PCM name 'Playback Channel Map' value.0 0 value.1 0 comment { access read type INTEGER count 2 range '0 - 36' } } control.45 { iface PCM device 1 name 'Playback Channel Map' value.0 0 value.1 0 comment { access read type INTEGER count 2 range '0 - 36' } } } --endcollapse-- !!All Loaded Modules !!------------------ Module fuse lockd sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter nf_conntrack_ipv4 nf_defrag_ipv4 ip6_tables xt_state nf_conntrack binfmt_misc snd_ens1371 gameport snd_rawmidi snd_ac97_codec ac97_bus snd_hda_codec_hdmi snd_hda_intel snd_hda_codec snd_hwdep snd_seq snd_seq_device serio_raw snd_pcm edac_core k8temp edac_mce_amd forcedeth snd_page_alloc snd_timer snd soundcore i2c_nforce2 asus_atk0110 ata_generic pata_acpi sata_nv pata_amd radeon i2c_algo_bit drm_kms_helper ttm drm i2c_core !!Sysfs Files !!----------- /sys/class/sound/hwC0D0/init_pin_configs: 0x03 0x18560010 /sys/class/sound/hwC0D0/driver_pin_configs: /sys/class/sound/hwC0D0/user_pin_configs: /sys/class/sound/hwC0D0/init_verbs: !!ALSA/HDA dmesg !!-------------- [ 1.213870] [drm] Connector 0: [ 1.213872] [drm] HDMI-A-1 [ 1.213873] [drm] HPD2 -- [ 3.542171] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 [ 3.542203] ALSA sound/pci/hda/hda_intel.c:2848 0000:01:00.1: Handle VGA-switcheroo audio client [ 3.542205] ALSA sound/pci/hda/hda_intel.c:3040 0000:01:00.1: Using LPIB position fix [ 3.542255] snd_hda_intel 0000:01:00.1: irq 45 for MSI/MSI-X [ 3.544349] ALSA sound/pci/hda/hda_intel.c:1716 0000:01:00.1: Enable sync_write for stable communication [ 3.550992] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:0e.0/0000:01:00.1/sound/card0/input5 [ 3.552906] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
The first card is the HDMI audio device. If you like to reorder your cards, put this configuration to a file named /etc/modprobe.d/alsa-reorder.conf (for example): options snd-ens1371 index=0 options snd-hda-intel index=1
No, my bug report was not about order, it lists the wrong card.
You have tree different audio hardware in your system: 1) Ensoniq PCI (the snd-ens1371 module/driver is correct) 2) Integrated analog (HDA compatible, probably) 3) HDMI HDA output (graphics card) In BIOS, you disabled only the analog HDA soundcard. Others are available. If PulseAudio does not save your preferred soundcard configuration, open a pulseaudio bug or reassing this bug to the pulseaudio package.
I actually have: motherboard built-in sound (diabled in BIOS): Realtek ALC850 6-channel CODEC that has 6-channel audio ports and a coaxial S/PDIF out port and supports Universal Audio Jack and Audio Sensing and Enumeration technologies. PCI card slot: Sound Blaster model # CT4750 with a Creative chip CT5880 There are no other hardware sound devices. Please explain your ideas about the mismatched naming. Thank you
HDMI HDA = sound card taking care about audio through the HDMI connection to your monitor. HDMI carries also audio data and the current implementation behaves like another soundcard in your system. So yes, your graphics card creates one extra soundcard.
So then, to put it simply, the HDMI channel (which is created by some unknown hardware) sends sound thru the video card's HDMI channel, should that be enabled and used. I could not get that to work, so I just use a stereo audio cable to the monitor's audio-in jack. In any case, I understand why that might be construed as another sound device. But then it should be labeled as such in device listings. It is not, and that is misleading. Further, the user wants to see a clear match to what they know they have in their system. Anything else is wrong, and only serves to confuse issues of every sort. Is there some reason that Fedora cannot get this right? Thanks.
Does anyone know why my primary sound card is not properly identified?
CT5880 is not emu10k1
Which is for the CT5880?
!!Advanced information - PCI Vendor/Device/Subsystem ID's !!------------------------------------------------------- 01:00.1 0403: 1002:aa60 Subsystem: 1682:aa60 -- 05:06.0 0401: 1274:5880 (rev 02) Subsystem: 1274:8001 static struct es1371_quirk es1371_ac97_reset_hack[] = { { .vid = PCI_VENDOR_ID_ENSONIQ, .did = PCI_DEVICE_ID_ENSONIQ_CT5880, .rev = CT5880REV_CT5880_C }, { .vid = PCI_VENDOR_ID_ENSONIQ, .did = PCI_DEVICE_ID_ENSONIQ_CT5880, .rev = CT5880REV_CT5880_D }, { .vid = PCI_VENDOR_ID_ENSONIQ, .did = PCI_DEVICE_ID_ENSONIQ_CT5880, .rev = CT5880REV_CT5880_E }, { .vid = PCI_VENDOR_ID_ENSONIQ, .did = PCI_DEVICE_ID_ENSONIQ_ES1371, .rev = ES1371REV_CT5880_A }, { .vid = PCI_VENDOR_ID_ENSONIQ, .did = PCI_DEVICE_ID_ENSONIQ_ES1371, .rev = ES1371REV_ES1373_8 }, { .vid = PCI_ANY_ID, .did = PCI_ANY_ID } }; you need to study pulseaudio udev-detect to find out how pulseaudio select default device after you disable onboard audio patcl list
did your graphic card have HDMI ?
Yes, the graphics card does, or so it says. However, there is no sound from that source thru HDMI, as I noted earlier. So that does not work correctly. I'm just a person who uses, tests and reports back on the software on my system. I do not study any software funcitonality, nor would I understand what, where or how. I believe you need to check with the software designers to understand that. Thanks.
you have to file abut in pulseaudio because ens1371 does not support Jack detection but HDMI and HDA support Jack detection pulseaudio swtich to available to HDMI
Sorry, but I don't understand. What do I have to file? What is this about Jack detection? Thanks.
https://bugs.freedesktop.org/enter_bug.cgi?product=PulseAudio
you have to provide pulseaudio verbose log pulseaudio -vvvv and pactl list
From pulseaudio -vvvv: I: [pulseaudio] main.c: setrlimit(RLIMIT_NICE, (31, 31)) failed: Operation not permitted I: [pulseaudio] main.c: setrlimit(RLIMIT_RTPRIO, (9, 9)) failed: Operation not permitted D: [pulseaudio] core-rtclock.c: Timer slack is set to 50 us. D: [pulseaudio] core-util.c: RealtimeKit worked. I: [pulseaudio] core-util.c: Successfully gained nice level -11. I: [pulseaudio] main.c: This is PulseAudio 2.1 D: [pulseaudio] main.c: Compilation host: x86_64-redhat-linux-gnu D: [pulseaudio] main.c: Compilation CFLAGS: -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -W -Wextra -Wno-long-long -Wvla -Wno-overlength-strings -Wunsafe-loop-optimizations -Wundef -Wformat=2 -Wlogical-op -Wsign-compare -Wformat-security -Wmissing-include-dirs -Wformat-nonliteral -Wpointer-arith -Winit-self -Wdeclaration-after-statement -Wfloat-equal -Wmissing-prototypes -Wredundant-decls -Wmissing-declarations -Wmissing-noreturn -Wshadow -Wendif-labels -Wcast-align -Wstrict-aliasing -Wwrite-strings -Wno-unused-parameter -ffast-math -fno-common -fdiagnostics-show-option D: [pulseaudio] main.c: Running on host: Linux x86_64 3.9.2-200.fc18.x86_64 #1 SMP Mon May 13 13:59:47 UTC 2013 D: [pulseaudio] main.c: Found 2 CPUs. I: [pulseaudio] main.c: Page size is 4096 bytes D: [pulseaudio] main.c: Compiled with Valgrind support: no D: [pulseaudio] main.c: Running in valgrind mode: no D: [pulseaudio] main.c: Running in VM: no D: [pulseaudio] main.c: Optimized build: yes D: [pulseaudio] main.c: FASTPATH defined, only fast path asserts disabled. I: [pulseaudio] main.c: Machine ID is ca9d061a6b646a89a6b4a6f70000007f. I: [pulseaudio] main.c: Using runtime directory /home/mpk/.pulse/ca9d061a6b646a89a6b4a6f70000007f-runtime. I: [pulseaudio] main.c: Using state directory /home/mpk/.pulse. I: [pulseaudio] main.c: Using modules directory /usr/lib64/pulse-2.1/modules. I: [pulseaudio] main.c: Running in system mode: no E: [pulseaudio] pid.c: Daemon already running. E: [pulseaudio] main.c: pa_pid_file_create() failed. From pactl list: Module #0 Name: module-device-restore Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Automatically restore the volume/mute state of devices" module.version = "2.1" Module #1 Name: module-stream-restore Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Automatically restore the volume/mute/device state of streams" module.version = "2.1" Module #2 Name: module-card-restore Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Automatically restore profile of cards" module.version = "2.1" Module #3 Name: module-augment-properties Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Augment the property sets of streams with additional static information" module.version = "2.1" Module #4 Name: module-alsa-card Argument: device_id="1" name="pci-0000_05_06.0" card_name="alsa_card.pci-0000_05_06.0" namereg_fail=false tsched=yes fixed_latency_range=no ignore_dB=no deferred_volume=yes card_properties="module-udev-detect.discovered=1" Usage counter: 0 Properties: module.author = "Lennart Poettering" module.description = "ALSA Card" module.version = "2.1" Module #5 Name: module-alsa-card Argument: device_id="0" name="pci-0000_01_00.1" card_name="alsa_card.pci-0000_01_00.1" namereg_fail=false tsched=yes fixed_latency_range=no ignore_dB=no deferred_volume=yes card_properties="module-udev-detect.discovered=1" Usage counter: 0 Properties: module.author = "Lennart Poettering" module.description = "ALSA Card" module.version = "2.1" Module #6 Name: module-udev-detect Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Detect available audio hardware and load matching drivers" module.version = "2.1" Module #7 Name: module-esound-protocol-unix Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "ESOUND protocol (UNIX sockets)" module.version = "2.1" Module #8 Name: module-native-protocol-unix Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Native protocol (UNIX sockets)" module.version = "2.1" Module #9 Name: module-gconf Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "GConf Adapter" module.version = "2.1" Module #10 Name: module-default-device-restore Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Automatically restore the default sink and source" module.version = "2.1" Module #11 Name: module-rescue-streams Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "When a sink/source is removed, try to move their streams to the default sink/source" module.version = "2.1" Module #12 Name: module-always-sink Argument: Usage counter: n/a Properties: module.author = "Colin Guthrie" module.description = "Always keeps at least one sink loaded even if it's a null one" module.version = "2.1" Module #13 Name: module-intended-roles Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Automatically set device of streams based of intended roles of devices" module.version = "2.1" Module #14 Name: module-suspend-on-idle Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "When a sink/source is idle for too long, suspend it" module.version = "2.1" Module #15 Name: module-systemd-login Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Create a client for each login session of this user" module.version = "2.1" Module #16 Name: module-position-event-sounds Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Position event sounds between L and R depending on the position on screen of the widget triggering them." module.version = "2.1" Module #17 Name: module-role-cork Argument: Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Mute & cork streams with certain roles while others exist" module.version = "2.1" Module #18 Name: module-filter-heuristics Argument: Usage counter: n/a Properties: module.author = "Colin Guthrie" module.description = "Detect when various filters are desirable" module.version = "2.1" Module #19 Name: module-filter-apply Argument: Usage counter: n/a Properties: module.author = "Colin Guthrie" module.description = "Load filter sinks automatically when needed" module.version = "2.1" Module #20 Name: module-dbus-protocol Argument: Usage counter: n/a Properties: module.author = "Tanu Kaskinen" module.description = "D-Bus interface" module.version = "2.1" Module #21 Name: module-switch-on-port-available Argument: Usage counter: n/a Properties: Module #22 Name: module-x11-publish Argument: display=:0.0 Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "X11 credential publisher" module.version = "2.1" Module #23 Name: module-x11-cork-request Argument: display=:0.0 Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "Synthesize X11 media key events when cork/uncork is requested" module.version = "2.1" Module #24 Name: module-x11-xsmp Argument: display=:0.0 session_manager=local/unix:@/tmp/.ICE-unix/1390,unix/unix:/tmp/.ICE-unix/1390 Usage counter: n/a Properties: module.author = "Lennart Poettering" module.description = "X11 session management" module.version = "2.1" Sink #0 State: SUSPENDED Name: alsa_output.pci-0000_05_06.0.analog-stereo Description: Sound Blaster 16PCI 4.1ch Analog Stereo Driver: module-alsa-card.c Sample Specification: s16le 2ch 44100Hz Channel Map: front-left,front-right Owner Module: 4 Mute: no Volume: 0: 100% 1: 100% 0: 0.00 dB 1: 0.00 dB balance 0.00 Base Volume: 63% -12.00 dB Monitor Source: alsa_output.pci-0000_05_06.0.analog-stereo.monitor Latency: 0 usec, configured 0 usec Flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY Properties: alsa.resolution_bits = "16" device.api = "alsa" device.class = "sound" alsa.class = "generic" alsa.subclass = "generic-mix" alsa.name = "ES1371 DAC2/ADC" alsa.id = "ES1371/1" alsa.subdevice = "0" alsa.subdevice_name = "subdevice #0" alsa.device = "0" alsa.card = "1" alsa.card_name = "Ensoniq AudioPCI" alsa.long_card_name = "Ensoniq AudioPCI ENS1371 at 0xb000, irq 16" alsa.driver_name = "snd_ens1371" device.bus_path = "pci-0000:05:06.0" sysfs.path = "/devices/pci0000:00/0000:00:09.0/0000:05:06.0/sound/card1" device.bus = "pci" device.vendor.id = "1274" device.vendor.name = "Ensoniq" device.product.id = "5880" device.product.name = "Sound Blaster 16PCI 4.1ch" device.string = "front:1" device.buffering.buffer_size = "65536" device.buffering.fragment_size = "65536" device.access_mode = "mmap+timer" device.profile.name = "analog-stereo" device.profile.description = "Analog Stereo" device.description = "Sound Blaster 16PCI 4.1ch Analog Stereo" alsa.mixer_name = "SigmaTel STAC9708,11" alsa.components = "AC97a:83847608" module-udev-detect.discovered = "1" device.icon_name = "audio-card-pci" Ports: analog-output;output-amplifier-on: Analog Output / Amplifier (priority: 9910) analog-output;output-amplifier-off: Analog Output / No Amplifier (priority: 9900) analog-output-mono;output-amplifier-on: Analog Mono Output / Amplifier (priority: 5010) analog-output-mono;output-amplifier-off: Analog Mono Output / No Amplifier (priority: 5000) analog-output-lfe-on-mono;output-amplifier-on: LFE on Separate Mono Output / Amplifier (priority: 4010) analog-output-lfe-on-mono;output-amplifier-off: LFE on Separate Mono Output / No Amplifier (priority: 4000) Active Port: analog-output;output-amplifier-on Formats: pcm Source #0 State: SUSPENDED Name: alsa_output.pci-0000_05_06.0.analog-stereo.monitor Description: Monitor of Sound Blaster 16PCI 4.1ch Analog Stereo Driver: module-alsa-card.c Sample Specification: s16le 2ch 44100Hz Channel Map: front-left,front-right Owner Module: 4 Mute: no Volume: 0: 100% 1: 100% 0: 0.00 dB 1: 0.00 dB balance 0.00 Base Volume: 100% 0.00 dB Monitor of Sink: alsa_output.pci-0000_05_06.0.analog-stereo Latency: 0 usec, configured 0 usec Flags: DECIBEL_VOLUME LATENCY Properties: device.description = "Monitor of Sound Blaster 16PCI 4.1ch Analog Stereo" device.class = "monitor" alsa.card = "1" alsa.card_name = "Ensoniq AudioPCI" alsa.long_card_name = "Ensoniq AudioPCI ENS1371 at 0xb000, irq 16" alsa.driver_name = "snd_ens1371" device.bus_path = "pci-0000:05:06.0" sysfs.path = "/devices/pci0000:00/0000:00:09.0/0000:05:06.0/sound/card1" device.bus = "pci" device.vendor.id = "1274" device.vendor.name = "Ensoniq" device.product.id = "5880" device.product.name = "Sound Blaster 16PCI 4.1ch" device.string = "1" module-udev-detect.discovered = "1" device.icon_name = "audio-card-pci" Formats: pcm Source #1 State: SUSPENDED Name: alsa_input.pci-0000_05_06.0.iec958-stereo Description: Sound Blaster 16PCI 4.1ch Digital Stereo (IEC958) Driver: module-alsa-card.c Sample Specification: s16le 2ch 44100Hz Channel Map: front-left,front-right Owner Module: 4 Mute: no Volume: 0: 100% 1: 100% 0: 0.00 dB 1: 0.00 dB balance 0.00 Base Volume: 100% 0.00 dB Monitor of Sink: n/a Latency: 0 usec, configured 0 usec Flags: HARDWARE DECIBEL_VOLUME LATENCY Properties: alsa.resolution_bits = "16" device.api = "alsa" device.class = "sound" alsa.class = "generic" alsa.subclass = "generic-mix" alsa.name = "ES1371 DAC2/ADC" alsa.id = "ES1371/1" alsa.subdevice = "0" alsa.subdevice_name = "subdevice #0" alsa.device = "0" alsa.card = "1" alsa.card_name = "Ensoniq AudioPCI" alsa.long_card_name = "Ensoniq AudioPCI ENS1371 at 0xb000, irq 16" alsa.driver_name = "snd_ens1371" device.bus_path = "pci-0000:05:06.0" sysfs.path = "/devices/pci0000:00/0000:00:09.0/0000:05:06.0/sound/card1" device.bus = "pci" device.vendor.id = "1274" device.vendor.name = "Ensoniq" device.product.id = "5880" device.product.name = "Sound Blaster 16PCI 4.1ch" device.string = "iec958:1" device.buffering.buffer_size = "65536" device.buffering.fragment_size = "65536" device.access_mode = "mmap+timer" device.profile.name = "iec958-stereo" device.profile.description = "Digital Stereo (IEC958)" device.description = "Sound Blaster 16PCI 4.1ch Digital Stereo (IEC958)" alsa.mixer_name = "SigmaTel STAC9708,11" alsa.components = "AC97a:83847608" module-udev-detect.discovered = "1" device.icon_name = "audio-card-pci" Ports: iec958-stereo-input: iec958-stereo-input (priority: 0) Active Port: iec958-stereo-input Formats: pcm Client #0 Driver: module-systemd-login.c Owner Module: 15 Properties: application.name = "Login Session 2" systemd-login.session = "2" Client #4 Driver: module-x11-xsmp.c Owner Module: 24 Properties: application.name = "XSMP Session on xfce4-session as 29f2401d4-618e-47de-b97d-d20c7d687df8" xsmp.vendor = "xfce4-session" xsmp.client.id = "29f2401d4-618e-47de-b97d-d20c7d687df8" Client #6 Driver: protocol-native.c Owner Module: 8 Properties: application.name = "ALSA plug-in [pnmixer]" native-protocol.peer = "UNIX socket client" native-protocol.version = "26" application.process.id = "1543" application.process.user = "mpk" application.process.host = "localhost.localdomain" application.process.binary = "pnmixer" window.x11.display = ":0.0" application.language = "en_US.UTF-8" application.process.machine_id = "ca9d061a6b646a89a6b4a6f70000007f" Client #7 Driver: protocol-native.c Owner Module: 8 Properties: application.name = "pactl" native-protocol.peer = "UNIX socket client" native-protocol.version = "26" application.process.id = "13970" application.process.user = "mpk" application.process.host = "localhost.localdomain" application.process.binary = "pactl" application.language = "en_US.UTF-8" window.x11.display = ":0.0" application.process.machine_id = "ca9d061a6b646a89a6b4a6f70000007f" Card #0 Name: alsa_card.pci-0000_05_06.0 Driver: module-alsa-card.c Owner Module: 4 Properties: alsa.card = "1" alsa.card_name = "Ensoniq AudioPCI" alsa.long_card_name = "Ensoniq AudioPCI ENS1371 at 0xb000, irq 16" alsa.driver_name = "snd_ens1371" device.bus_path = "pci-0000:05:06.0" sysfs.path = "/devices/pci0000:00/0000:00:09.0/0000:05:06.0/sound/card1" device.bus = "pci" device.vendor.id = "1274" device.vendor.name = "Ensoniq" device.product.id = "5880" device.product.name = "Sound Blaster 16PCI 4.1ch" device.string = "1" device.description = "Sound Blaster 16PCI 4.1ch" module-udev-detect.discovered = "1" device.icon_name = "audio-card-pci" Profiles: output:analog-mono: Analog Mono Output (sinks: 1, sources: 0, priority. 100) output:analog-mono+input:analog-mono: Analog Mono Duplex (sinks: 1, sources: 1, priority. 101) output:analog-mono+input:analog-stereo: Analog Mono Output + Analog Stereo Input (sinks: 1, sources: 1, priority. 160) output:analog-mono+input:iec958-stereo: Analog Mono Output + Digital Stereo (IEC958) Input (sinks: 1, sources: 1, priority. 155) output:analog-stereo: Analog Stereo Output (sinks: 1, sources: 0, priority. 6000) output:analog-stereo+input:analog-mono: Analog Stereo Output + Analog Mono Input (sinks: 1, sources: 1, priority. 6001) output:analog-stereo+input:analog-stereo: Analog Stereo Duplex (sinks: 1, sources: 1, priority. 6060) output:analog-stereo+input:iec958-stereo: Analog Stereo Output + Digital Stereo (IEC958) Input (sinks: 1, sources: 1, priority. 6055) output:analog-surround-40: Analog Surround 4.0 Output (sinks: 1, sources: 0, priority. 700) output:analog-surround-40+input:analog-mono: Analog Surround 4.0 Output + Analog Mono Input (sinks: 1, sources: 1, priority. 701) output:analog-surround-40+input:analog-stereo: Analog Surround 4.0 Output + Analog Stereo Input (sinks: 1, sources: 1, priority. 760) output:analog-surround-40+input:iec958-stereo: Analog Surround 4.0 Output + Digital Stereo (IEC958) Input (sinks: 1, sources: 1, priority. 755) output:iec958-stereo: Digital Stereo (IEC958) Output (sinks: 1, sources: 0, priority. 5500) output:iec958-stereo+input:analog-mono: Digital Stereo (IEC958) Output + Analog Mono Input (sinks: 1, sources: 1, priority. 5501) output:iec958-stereo+input:analog-stereo: Digital Stereo (IEC958) Output + Analog Stereo Input (sinks: 1, sources: 1, priority. 5560) input:analog-mono: Analog Mono Input (sinks: 0, sources: 1, priority. 1) input:analog-stereo: Analog Stereo Input (sinks: 0, sources: 1, priority. 60) input:iec958-stereo: Digital Stereo (IEC958) Input (sinks: 0, sources: 1, priority. 55) off: Off (sinks: 0, sources: 0, priority. 0) Active Profile: output:analog-stereo+input:iec958-stereo Ports: analog-output;output-amplifier-on: Analog Output / Amplifier (priority: 9910) Part of profile(s): output:analog-mono, output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-mono+input:iec958-stereo, output:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-stereo+input:iec958-stereo, output:analog-surround-40, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:analog-surround-40+input:iec958-stereo analog-output;output-amplifier-off: Analog Output / No Amplifier (priority: 9900) Part of profile(s): output:analog-mono, output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-mono+input:iec958-stereo, output:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-stereo+input:iec958-stereo, output:analog-surround-40, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:analog-surround-40+input:iec958-stereo analog-output-mono;output-amplifier-on: Analog Mono Output / Amplifier (priority: 5010) Part of profile(s): output:analog-mono, output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-mono+input:iec958-stereo, output:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-stereo+input:iec958-stereo analog-output-mono;output-amplifier-off: Analog Mono Output / No Amplifier (priority: 5000) Part of profile(s): output:analog-mono, output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-mono+input:iec958-stereo, output:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-stereo+input:iec958-stereo analog-output-lfe-on-mono;output-amplifier-on: LFE on Separate Mono Output / Amplifier (priority: 4010) Part of profile(s): output:analog-mono, output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-mono+input:iec958-stereo, output:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-stereo+input:iec958-stereo, output:analog-surround-40, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:analog-surround-40+input:iec958-stereo analog-output-lfe-on-mono;output-amplifier-off: LFE on Separate Mono Output / No Amplifier (priority: 4000) Part of profile(s): output:analog-mono, output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-mono+input:iec958-stereo, output:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-stereo+input:iec958-stereo, output:analog-surround-40, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:analog-surround-40+input:iec958-stereo analog-input-microphone;input-microphone-1: Microphone / Microphone 1 (priority: 8720) Part of profile(s): output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:iec958-stereo+input:analog-mono, output:iec958-stereo+input:analog-stereo, input:analog-mono, input:analog-stereo analog-input-microphone;input-microphone-2: Microphone / Microphone 2 (priority: 8719) Part of profile(s): output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:iec958-stereo+input:analog-mono, output:iec958-stereo+input:analog-stereo, input:analog-mono, input:analog-stereo analog-input-linein: Line In (priority: 8100) Part of profile(s): output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:iec958-stereo+input:analog-mono, output:iec958-stereo+input:analog-stereo, input:analog-mono, input:analog-stereo analog-input: Analog Input (priority: 8000) Part of profile(s): output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:iec958-stereo+input:analog-mono, output:iec958-stereo+input:analog-stereo, input:analog-mono, input:analog-stereo analog-input-video: Video (priority: 7000) Part of profile(s): output:analog-mono+input:analog-mono, output:analog-mono+input:analog-stereo, output:analog-stereo+input:analog-mono, output:analog-stereo+input:analog-stereo, output:analog-surround-40+input:analog-mono, output:analog-surround-40+input:analog-stereo, output:iec958-stereo+input:analog-mono, output:iec958-stereo+input:analog-stereo, input:analog-mono, input:analog-stereo iec958-stereo-input: iec958-stereo-input (priority: 0) Part of profile(s): output:analog-mono+input:iec958-stereo, output:analog-stereo+input:iec958-stereo, output:analog-surround-40+input:iec958-stereo, input:iec958-stereo iec958-stereo-output: Digital Output (S/PDIF) (priority: 0) Part of profile(s): output:iec958-stereo, output:iec958-stereo+input:analog-mono, output:iec958-stereo+input:analog-stereo Card #1 Name: alsa_card.pci-0000_01_00.1 Driver: module-alsa-card.c Owner Module: 5 Properties: alsa.card = "0" alsa.card_name = "HD-Audio Generic" alsa.long_card_name = "HD-Audio Generic at 0xd1020000 irq 45" alsa.driver_name = "snd_hda_intel" device.bus_path = "pci-0000:01:00.1" sysfs.path = "/devices/pci0000:00/0000:00:0e.0/0000:01:00.1/sound/card0" device.bus = "pci" device.vendor.id = "1002" device.vendor.name = "Advanced Micro Devices [AMD] nee ATI" device.product.id = "aa60" device.product.name = "Redwood HDMI Audio [Radeon HD 5000 Series]" device.string = "0" device.description = "Redwood HDMI Audio [Radeon HD 5000 Series]" module-udev-detect.discovered = "1" device.icon_name = "audio-card-pci" Profiles: output:hdmi-stereo: Digital Stereo (HDMI) Output (sinks: 1, sources: 0, priority. 5400) off: Off (sinks: 0, sources: 0, priority. 0) Active Profile: off Ports: hdmi-output-0: HDMI / DisplayPort (priority: 5900, not available) Part of profile(s): output:hdmi-stereo
pulseaudio use Jack detection and your HDMI not present ande your onboard ich AC97 controller (alc850 AC97 coded) and end1371 does not support Jack detection you have to shutdown pulseaudio and restart pulseaudio to get the verbose log state.Generic { control.1 { iface CARD name 'HDMI/DP,pcm=3 Jack' value false comment { access read type BOOLEAN count 1 } }
How can I get that?
https://fedoraproject.org/wiki/How_to_debug_PulseAudio_problems you have to disable autospwan to get the log and enable autospwan after you get the log
Created attachment 915727 [details] Comment (This comment was longer than 65,535 characters and has been moved to an attachment by Red Hat Bugzilla).
paman shows "Sound Blaster 16PCI 4.1ch Analog Stereo" should be Creative Labs CT4750 PCI 128 Sound Blaster Audio Card
the description is composed by pulseaudio with card name and profile in http://cgit.freedesktop.org/pulseaudio/pulseaudio/tree/src/modules/alsa/alsa-util.c
05:06.0 0401: 1274:5880 (rev 02) Subsystem: 1274:8001 http://pci-ids.ucw.cz/read/PC/1274/5880/12748001
I couldn't find the name in the file. Did you mean it was composed "by" the file you linked? Your other link showed that it was obviously selecting the wrong one, which has been my whole point from the beginning.
This message is a reminder that Fedora 17 is nearing its end of life. Approximately 4 (four) weeks from now Fedora will stop maintaining and issuing updates for Fedora 17. It is Fedora's policy to close all bug reports from releases that are no longer maintained. At that time this bug will be closed as WONTFIX if it remains open with a Fedora 'version' of '17'. Package Maintainer: If you wish for this bug to remain open because you plan to fix it in a currently maintained version, simply change the 'version' to a later Fedora version prior to Fedora 17's end of life. Bug Reporter: Thank you for reporting this issue and we are sorry that we may not be able to fix it before Fedora 17 is end of life. If you would still like to see this bug fixed and are able to reproduce it against a later version of Fedora, you are encouraged change the 'version' to a later Fedora version prior to Fedora 17's end of life. Although we aim to fix as many bugs as possible during every release's lifetime, sometimes those efforts are overtaken by events. Often a more recent Fedora release includes newer upstream software that fixes bugs or makes them obsolete.
Created attachment 768928 [details] from Hardware Lister Shows the wrong card and manufacturer.
http://pci-ids.ucw.cz/read/PC/1274/5880 you have to discuss/update the description of http://pci-ids.ucw.cz/read/PC/1274/5880/12748001 and wait until package hwdata use the updated pci.ids
Thank you. I have posted a comment there in the discussion regarding that product.
Fedora 17 changed to end-of-life (EOL) status on 2013-07-30. Fedora 17 is no longer maintained, which means that it will not receive any further security or bug fix updates. As a result we are closing this bug. If you can reproduce this bug against a currently maintained version of Fedora please feel free to reopen this bug against that version. Thank you for reporting this bug and we are sorry it could not be fixed.